• Journal of Korean Society for Atmospheric Environment
• /
• 제13권3호
• /
• pp.193-205
• /
• 1997

Experiments on granular filtration of polydispersed aerosols were conducted to determine the changes in pressure drop necessary to maintain a given gas flow rate as filter becomes clogged with deposited particles. Among the various variables which affect the increase in the pressure drop during the filtration, the most important one was found to be the size of the deposited aerosol particles. It was shown that for a given extent of the total deposition, the extent of increase in pressure drop increases with the decrease of the deposited aerosol size. For the general case where the deposited particles have different sizes, a procedure was proposed for correlating and predicting experimental results on pressure drop. This procedure was found applicable to bidispersed aerosols and polydispersed aerosols.

• Journal of the Korean Chemical Society
• /
• 제14권3호
• /
• pp.229-235
• /
• 1970

Electrodeposition of lead peroxide on the graphite core was studied. The results are following; 1) At more noble potential than 1.6V vs. S.C.E. and lower temperature than $40^{\circ}C$, $PbO_2$ deposited current efficiency is increased but deposited layer falls off easily from graphite core. 2) Oxygen overvoltage of $PbO_2$ deposited layer on the graphite core is largely with increasing $PbO_2$ depositing anodic potential and with lowlying electrolytic temperature. 3) To obtain the $PbO_2$ deposited layer without falling off from the graphite core, it is necessary to change the electrolytic conditions, anodic potential and electrolytic temperature, in four stages successively.

• The Korean Journal of Ceramics
• /
• 제3권1호
• /
• pp.29-33
• /
• 1997

Four diamond films were deposited by the microwave plasma assisted chemical vapor deposition method varying CH4 concentration from 2.5 to 10% in the feeding gases. Thermal conductivity was measured on these free standing films by the steady state method from 80 K to 400K. They showed higher thermal conductivity as the film deposited with lower methane concentration. One exception, 7.79% methane concentration deposited film, was observed to be the highest thermal conductivity. Phonon scattering processes were considered to analyze the thermal conductivity with the full Callaway model. The grain size and the concentration of the extended and the point defects were used as the fitting parameters. Microstructure of diamond films was investigated with the scanning electron microscopy and Raman spectroscopy.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 한국전기전자재료학회 2008년도 하계학술대회 논문집 Vol.9
• /
• pp.405-406
• /
• 2008

The amorphous indium zinc oxide (IZO) thin films were deposited on polyethersulfone (PES) and glass substrates by facing targets sputtering. IZO thin films deposited as functions of gas flow ratio on PES and glass substrates, respectively. The electrical, optical and structural properties of IZO thin films were evaluated by a Hall Effect Measurement, an X-Ray Diffractormeter, UV/VIS spectrometer in visible range and a scanning electron microscopy, respectively. As-deposited IZO thin films exhibited resistivity of $5.4\times10^{-4}$ and $4.5\times10^{-4}$ [$\Omega$-cm] on PES and glass substrates, respectively. The optical transmittance showed over 85% in the visible region on PES and glass substrates.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• 제55권10호
• /
• pp.475-480
• /
• 2006

Vanadium oxide thin films (VOx) have been deposited by RF magnetron sputtering from $V_2O_5$ target under different oxygen partial pressure ratios(0%, 10%) and substrate temperatures$(27^{\circ}C,\;400^{\circ}C)$. Crystallographic structure and morphology of the films are studied by XRD and SEM. Humidity-sensing properties of resistive sensors having interdigitated electrode structure are characterized through electrical conduction measurements. The films deposited at room temperature are amorphous whereas the ones deposited above foot are polycrystalline. The sensors show good response to humidity over 20%RH to 80%RH. Vanadium oxide thin films deposited with $0%O_2$ partial pressure at $400^{\circ}C$ exhibit greater sensitivity to humidity change than others.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• 제53권7호
• /
• pp.387-394
• /
• 2004

Diamond films were deposited on the cemented tungsten carbide WC-Co cutting insert substrates by using both microwave plasma chemical vapor deposition(MWPCVD) and radio frequency plasma chemical vapor deposition (RFPCVD) from $CH_4$$-H_2$$-O_2$ gas mixture. Scanning electron microscopy and X-ray diffraction techniques were used to investigate the microstructure and phase analysis of the materials and Raman spectrometry was used to characterize the quality of the diamond coating. Diamond films deposited using MWPCVD from $CH_4$$-H_2$$-O_2$ gas mixture show a dense, uniform, well faceted and polycrystalline morphology. The compressive stress in the diamond film was estimated to be (1.0∼3.6)$\pm$0.9 GPa. Diamond films which were deposited on the WC-Co cutting insert substrates by RFPCVD from $CH_4$$-H_2$$-O_2$ gas mixture show relatively good adhesion, very uniform, dense and polycrystalline morphology.

• Proceedings of the IEEK Conference
• /
• 대한전자공학회 2007년도 하계종합학술대회 논문집
• /
• pp.441-442
• /
• 2007

We deposited nickel oxide(NiO) thin films on silicon(Si) substrates at Room temperature and $500^{\circ}C$ using a nickel target by reactive DC and RF sputtering. In addition, we anneal to NiO thin films deposited at room temperature. Using spectroscopic eillipsometry, we obtained optical characteristics of every films. We discussed relations of the optical and structural properties of NiO thin films with the oxygen flow rate, substrate temperature and annealing temperatures. Refraction was decreased and defect was increased when NiO thin films was annealed. We also analyzed the electrical characteristics of NiO films which deposited DC and RF sputtering method.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 한국재료학회 2009년도 춘계학술발표대회
• /
• pp.52.1-52.1
• /
• 2009

Cupric oxide (CuO) is a p-type semiconductor with band gap of ~1.7 eV and reported to be suitable for catalysis, lithium-copper oxide electrochemical cells, and gas sensors applications. The nanoparticles, plates and nanowires of CuO were found sensing to NO2, H2S and CO. In this work, we report about the comparison about hydrogen sensing of nano thin film and nanowires structured CuO deposited on single-walled carbon nanotubes (SWNTs). The thin film and nanowires are synthesized by deposition of Cu on different substrate followed by oxidation process. Nano thin films of CuO are deposited on thermally oxidized silicon substrate, whereas nanowires are synthesized by using a porous thin film of SWNTs as substrate. The hydrogen sensing properties of synthesized materials are investigated. The results showed that nanowires cupric oxide deposited on SWNTs showed higher sensitivity to hydrogen than those of nano thin film CuO did.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 한국전기전자재료학회 2000년도 하계학술대회 논문집
• /
• pp.427-431
• /
• 2000

ITO (indium tin oxide) thin films on PET (polyethylene terephthalate) and glass substrates have been deposited by a dc magnetron sputtering without heat treatments such as substrate heater and post heat treatment. Each sputtering parameter during the sputtering deposition is an important factor for the high quality of ITO thin films deposited on polymeric substrate. Particularly, the material, electrical and optical properties of as-deposited ITO oxide films are dominated by sputtering power, oxygen partial pressure and films thickness. As the experimental results, the XRD patters of ITO films are influenced by sputtering power and pressure. As the power and pressure are increased, (411) peak is grown suddenly. the electrical resistivity is also increased, as the sputteing power and pressure are increased. Transmittance of ITO thin films in visible light ranges is lowered with increasing the sputtering power and film thickness. Reflectance of ITO films in infia-red region is decreased, as the power and pressure is increased.

• Journal of the Korean Ceramic Society
• /
• 제21권2호
• /
• pp.156-164
• /
• 1984

The characteristic of pyrolytic carbon deposited in a fluidized bed as measured by density apparent crystallite size and viewed metallographically under polarized light can be easily controlled by adjusting the deposition parameters such as deposition temperature and propane flow rate or silicon content. The density of isotopic pyrolytic carbons deposited from propane between 120$0^{\circ}C$ and 140$0^{\circ}C$ increases with increasing propane flow rate and decreasing deposition temperature from 1, 73g/cc to 2.08g/cc. The apparent crystallite size Lc parameter appears to depend only on deposition temperature being entirely independent of the propane flow rate. The carbon matrix density of the silicon-alloyed carbonds deposited from propane and methyltrichlorosil-ane from 2.05g/cc for a silicon content around 9wt% to 2.67g/cc for a silicon content of 36.7wt% The Lc parameter of the deposition temperature being entirely independent of the silicon content.