• Journal of IKEEE
• /
• v.3 no.2 s.5
• /
• pp.186-195
• /
• 1999

In this paper, the RF-modules composed of front-end, frequency synthesizer, modulator/demodulator and power control multi channel WLL personal system for W-CDMA using 10 [MHz] RF channel bandwidth has been implemented and considered. The measured transmission power is 250 [mW] which is very close to the required value. The measured flatness of power at the final output stage is ${\pm}1.5[dB]$ over the required bandwidth of the receiver. In addition, it is found that the chip rate transmitting spread signal is set to 8.192 [MHz], the required rate. The frequencies of RF_LO signal and LO signal of the modulator and the demodulator measured by a frequency synthesizer are satisfied with design requirements. The operating range of the receiving strength signal indicator and AGC units shows 60 [dB] respectively. Also the measured phasor diagram and eye pattern for deciding the RF modules compatible with baseband digital signal processing part are shown good results.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.10 no.4
• /
• pp.60-73
• /
• 1973

The reactor noise analysis was performed by the cross correlation method using two detectors to determine the dynamic stability and the system parameter of TRIGA Mark-II reactor under critical and subcritical conditions. The a values turned out to be 46.67 and 70.04 respectively at zero power and full power under critical condition, while 79.47 and 97.59 respectively at the safety rod dropping and the regulating rod dropping under subcritical condition. Prompt neutron life time of TRIGA Mark-II reactor measured 107 and 160 $\mu$sec, and shut down margin was -10.03$\times$10-4 at the safety rod dropping and -29-43$\times$10-4 at the regulating rod dropping CDC 3100/MSOS digital computer, HITACHI 505 Analog computer, and preamplifier, bandpass filter, FM modulator or demodulator designed for this specific purpose, were employed for the present investigation.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.53 no.9
• /
• pp.67-74
• /
• 2016

This paper presents a novel multiple orthogonal subcarrier modulation based UHF band RFID communication system. In tag-to-reader communication, the demonstration system can deliver 1.6 Mbps through four subcarriers. To improve data rate while suppressing increase in circuit complexity, tag employs square-waves as the subcarriers and uses individual load modulators for each subcarrier. By using multiple orthogonal subcarrier based modulation, proposed communication system can be operated under existing UHF band RFID regulation. In reader, an OFDM demodulator is used. Since the tag backscatters the reader's CW carrier, carrier frequency offset compensation is not necessary in reader demodulator. Experimental results show that the demonstration system achieves a bit error rate of 10-5 at an Eb/N0 of 10.8 dB.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.43 no.1 s.343
• /
• pp.25-32
• /
• 2006

We propose a new M-ary state-transition FSK modulator technique for enhancing demodulator's symbol timing recovery which can be applied to acoustic MODEM. In the previous technique, the demodulator's symbol timing performance can degrade when the sequences of same symbols are transmitted. This proposed method, because the transmission symbol changes in every single symbol period, increases the synchronization performance dramatically and has a simple MODEM and frame structure. On the one hand, we improve modulation-derived synchronization(MDS) which is M-ary FSK's symbol timing recovery scheme, then analyze it. Finally the proposed method is analyzed from the viewpoint of frequency efficiency, which proves this method is appropriate for acoustic MODEM.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.26 no.12B
• /
• pp.1677-1685
• /
• 2001

In this paper, we propose a call admission control scheme that can be performed within guaranteeing of required QoS(Quality of Services) in DS-CDMA(Direct Sequence-Code Division Multiple Access) reverse link. It has been performed rely on a physical channel numberonly and based on quality of received signal from MODEM(modulator/demodulator) part in established study. In other methods, the standard for services would have been set from statistical analysis of users\` location and using received power level in BTS(Base Transceiver Station). These ways bring about not only system loads but time delay or great differences from real environment. To solve these problems, we propose a call drop rate estimation algorithm for the purpose of call admission control based on measured value at LNA(Low Noise Amplifier) ports of BTS(Base Transceiver Station) in real time. This method proposed in this paper estimates a quality of offered service in real time, reduce system loads and shorten time delay which is needed to determine the standard for call admission control. But it requires a additional 17W complexity which can measure received signal power in BTS and estimate call drop rate.

• The Journal of the Korea Contents Association
• /
• v.6 no.1
• /
• pp.8-13
• /
• 2006

In this thesis, an automatic door lock system using a dual tone multiple frequency(DTMF) signal generated as pushing the key button of mobile phone is proposed and implemented. This system consists of a transmitter module and a receiver module for processing the DTMF signal of mobile phone. The DTMF signal of mobile phone connected with ear-phone jack enter into the input terminal of DTMF receiver and those are encoded by a code-converter with 4-bits binary format in the DTMF receiver. The encoded output signals are transmitted to the amplitude shift keying(ASK) modulator of transmitter module and the modulated ASK signals which are converted into radio frequency(RF) signals propagate in a free space. The RF signals passed through a free space are demodulated by the ASK demodulator of receiver module and the demodulated ASK signals are sent to a micro-controller unit(MCU). The output signals processed by the MCU are compared with the secreted identification number which is prerecorded in a microprocessor and are transferred to a power relay. If the result is the same, the automatic door lock system opens a door. In the opposite case, it maintains closing the door. The implemented automatic door lock system operates well in mobile environments.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.47 no.2
• /
• pp.100-105
• /
• 2010

In this paper, a FM radio receiver integrated circuit has been developed based on $0.5{\mu}m$ CMOS process for Zero-Crossing FM demodulator over the 88MHz to 108MHz band. The receiver is designed with the low-IF architecture, and includes Low Noise Amplifier(LNA), Down-Conversion Mixer, Phase Locked Loop(PLL), IF LPF, and a comparator. The measured results of the LNA and Mixer show that the conversion gain of 23.2 dB, the input PldB of -14 dBm, and the noise figure of 15 dB. The measured analog block of the LPF and comparator show the voltage gain of over 89 dB, and the IF LPF can configure the passband from 600KHz to 1.3MHz with 100KHz step through the internal control register banks. The designed FM radio receiver operates at 4.5V with the total current consumption of 15.3mA, so the total power consumption is about 68.85mW. The commercial FM radio has been successfully received.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.32 no.5
• /
• pp.50-57
• /
• 2004

For the application of structural health monitoring such as AE detection, a stabilized FBG sensor system with wide dynamic range was proposed. A tunable Fabry-Perot filter with narrow free spectral range(FSR) was used to simplify the multiplexing demodulator for FBG vibration sensors. Stabilization controlling system was also developed for the maintenance of maximum sensitivity of the sensors. In order to verify the performance of the proposed FBG vibration sensor system, we measured sensitivity, and the system showed the average sensitivity of 256 $n{\in}_{mas}/{\sqrt{Hz}}$. Finally, multi-points vibration tests using in-line FBG sensors were conducted to validate the multiplexing performance of the FBG system.

• Journal of Advanced Navigation Technology
• /
• v.17 no.6
• /
• pp.705-711
• /
• 2013

In this paper, we present a low-complexity non-coherent demodulation algorithm and hardware architecture for LR-WPAN systems which can support the variable data rate for various applications. The need for LR-WPAN systems that can support the variable data rate is increasing due to the emergence of various sensor applications. Since the existing symbol based double correlation (SBDC) algorithm requires the increase of complexity to support the variable data rate, we propose the sample based double correlation (SPDC) algorithm which can be implemented without the increase of complexity. The proposed non-coherent demodulator was designed by verilog HDL and implemented with FPGA prototype board.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2009.10a
• /
• pp.153-156
• /
• 2009

The interferometric fiber optic gyroscopes (FOGs) are well known as sensors of rotation, which are based on Sagnac effect, and have been under development for a number of years to meet a wide range of performance requirements. This paper describes the development of open-loop FOG and digital signal processing techniques implemented on FPGA. Our primary goal was to obtain intermediate accuracy (pointing grade) with a good bias stability ($0.22^{\circ}/hr$) and scale factor stability, extremely low angle random walk ($0.07^{\circ}/\sqrt{hr}$) and significant cost savings by using a single mode fiber. A secondary goal is to design all digital FOG signal processing algorithms with which the SNR at the digital demodulator output is enhanced substantially due to processing gain. The CIC type of decimation block only requires adders and shift registers, low cost processors which has low computing power still can used in this all digital FOG processor.