• 설비공학논문집
• /
• 제22권6호
• /
• pp.369-374
• /
• 2010

A refrigerant-subcooling refrigeration system consisted of a typical single vapor-compression refrigeration cycle, a subcooler, and an ice storage tank. The degree of subcooling at the exit of the condenser can be increased by the heat exchange between the subcooler and the ice storage tank. The cold heat in the ice storage tank was stored by using the refrigeration cycle during night time and then used to absorb the heat from the subcooler during daytime. The performance of the refrigerant-subcooling refrigeration system was measured by varying the degree of subcooling. In addition, the performance characteristics of the present system were compared with those of a conventional refrigeration system. The mass flow rate of the present system was higher than that of the conventional system due to the increase in the degree of subcooling. Generally, the refrigerant-subcooling system showed superior performance to the conventional refrigeration system.

• 설비공학논문집
• /
• 제22권12호
• /
• pp.845-851
• /
• 2010

This study was experimentally performed to find the effects of refrigerant subcooling in the refrigeration system and to propose how to get the efficient use of energy. A refrigerant-subcooling refrigeration system consisted of a typical single vapor-compression refrigeration cycle, a subcooler, and an ice storage tank. The degree of subcooling at the exit of the condenser can be increased by the heat transfer between the subcooler and the ice storage tank. The cold heat in the ice storage tank was stored by using the refrigeration cycle during night time and then used to absorb the heat from the subcooler during daytime. The cooling capacity and COP of this system were higher than those of the conventional system due to the increase in the degree of subcooling. Typically, the refrigerant-subcooling system showed superior performance to the conventional refrigeration system and would also contribute to load leveling.

• 수산해양교육연구
• /
• 제25권2호
• /
• pp.301-306
• /
• 2013

In this paper, cycle performance analysis of two-stage compression and two-stage expansion refrigeration system using alternative freon refrigerants is presented to offer the basic design data for the operating parameters of the system. Alternative freon refrigerant for freon refrigerant R22 were used as working fluids in this study. The operating parameters considered in this study included evaporation temperature, condensation temperature, subcooling degree, superheating degree, and mass flow rate ratio of inter-cooler. The main results were summarized as follows : The COP of two-stage compression and two-stage expansion refrigeration system increases with the increasing subcooling degree and mass flow rate ratio of inter-cooler, but decreases with the increasing evaporating temperature, condensing temperature and superheating degree. Therefore, subcooling degree, mass flow rate ratio of inter-cooler of two-stage compression and two-stage expansion refrigeration system using alternative freon refrigerants have an effect on COP of this system.

• 에너지공학
• /
• 제8권4호
• /
• pp.576-582
• /
• 1999

과냉각수 이용 아이스슬러리 제빙시스템은 기존 제빙방식에 배히 많은 장점이 있지만, 열교환기 내 빙결정의 성장으로 인한 관내동결이 발생하기 쉽다. 이러한 관내동결조건을 알아보기 위한 기본실험으로 정지상태 증류수와 수도수의 과냉각도를 알아보고 시험관재질이 과냉각도에 미치는 영향 등에 대해 검토하였다. 또한 , 첨가한 메타알데이드 농도가 임계 과냉각 해소범위가 좁게 나타났으며, 과냉각 해소에대한 시험관별 표준편차는 파이렉스 경우 1.8 스테인레스강 2.0을 보였다. 최소 과냉각도는 파이렉스 6.2$^{\circ}C$ , 스테인레스 5.5$^{\circ}C$ 로서 파이렉스가 약 0.7$^{\circ}C$크게 나타났다. 메타알데히드는 실험횟수가 증가하여도 그 성질을 유지하면서 빙 활성화물질로써 작용하는 것으로 나타났다.

• Journal of Advanced Marine Engineering and Technology
• /
• 제36권5호
• /
• pp.580-585
• /
• 2012

R744용 해양온도차 발전 시스템의 작동변수에 대한 기초 설계자료를 제공하고자 증발열량, 응축열량, 전체일량, 효율에 대한 사이클 성능을 분석하였다. 본 연구에서 고려된 작동변수는 R744 해양온도차 발전 사이클의 과열도, 과냉각도, 응축온도, 증발온도 등이다. 주요 결과를 요약하면 다음과 같다. R744의 증발열량은 과열도와 과냉각도가 증가할수록 증가하는 반면, 응축온도가 증가할수록 감소한다. 전체일량은 R744의 과열도와 과냉각도와 함께 증가하나 증발온도는 증가할수록 감소한다. 그리고 효율은 과열도와 과냉각도가 증가할수록 증가하는 반면, 응축온도는 감소한다. 그러므로 R744용 해양온도차 발전 시스템의 증발열량, 응축열량, 전체일량, 효율은 과열도, 과냉각도, 응축온도, 증발온도, 펌프와 터빈 효율에 영향을 받는 것을 알 수 있었다. 따라서 R744용 해양온도차 발전 시스템의 설계시에는 이러한 영향을 면밀하게 파악하여야 한다.

• Nuclear Engineering and Technology
• /
• 제36권5호
• /
• pp.460-474
• /
• 2004

Effects of liquid subcooling on pool boiling heat transfer in an annulus with an open bottom have been investigated experimentally. A tube of 19.1mm diameter and the water at atmospheric pressure have been used for the fest. Up to $50^{\circ}C$ of liquid subcooling has been tested and experimental data of the annulus have been compared with the data of a single unrestricted tube. Temperatures on the heated tube surface fluctuate only slightly regardless of the heat flux in the annulus, whereas high variation is observed on the surface of the single tube. An increase in the degree of subcooling decreases heat transfer coefficients greatly both for the single tube and the annulus. Heat transfer coefficients increase suddenly at ${\Delta}T_{sub}\;{\le}\;10^{\circ}C$ and much greater change in heat transfer coefficients is observed at the annulus. To obtain effects of subcooling on heat transfer quantitatively, two new empirical equations have been suggested, and the correlations predict the empirical data within ${\pm}30\%$ error bound excluding some data at lower heat transfer coefficients.

• 대한기계학회논문집B
• /
• 제24권4호
• /
• pp.485-494
• /
• 2000

The purpose of this paper is to investigate a critical heat flux(CHF) during forced convective subcooled and saturated boiling in free water jet system impinged on a rectangular heated surface. The surface is supplied with subcooled or saturated water through a rectangular jet. Experimental parameters studied are a width of heated surface, a height of supplementary water and a degree of subcooling. Incipient boiling point is observed in the temperature of 6${\~}8^{\circ}C$ of superheat of test specimen. CHF depends on jet velocity for various boiling-involved coolant system. CHF also is proportional to the nozzle exit velocity to the power of n, where n is 0.55 and 0.8 for subcooled and saturated boiling, respectively. CHF is enhanced with a higher jet velocity, higher degree of subcooling and smaller width of a heated surface.

• International Journal of Air-Conditioning and Refrigeration
• /
• 제7권
• /
• pp.79-90
• /
• 1999

This investigation presents the experimental results of forced convection boiling heat transfer around a circular, electrically heated horizontal cylinder to subcooled water in cross flow. In these experiments, the following primary variables were included: heat flux, flow velocity, pressure and degree of subcooling at inlet. Local surface temperatures were measured at nine peripheral positions. Local surface temperature distributions are classified into four categories depending on the supplied heat flux. The effects of the boiling curve depending on the fluid velocity, degree of subcooling at inlet and pressure are presented.

• 대한기계학회논문집
• /
• 제17권8호
• /
• pp.2079-2087
• /
• 1993

The effects of subcooling and natural convection are studied numerically on the melting process of an initially subcooled phase-change medium filled inside a horizontal circular cylinder. It is postulated that melting continues with the tube wall kept at a constant temperature and with the unmelted solid core fixed. Primary emphasis is placed on the evolution of interface morphology, the local/overall heat transfer rate at the tube wall and at the interface, and the structure of natural convection. The numerical results are mainly presented in terms of the Rayleigh and subcooling numbers. As the degree of subcooling intensifies, the melting rate and the movement of the interface are impeded but the interfaces are of similar shape with the passage of time. The heat transfer characteristics are found to be mostly governed by the formation pattern of natural convection in the liquid phase. Good agreement with available experimental data is found.

• 한국태양에너지학회 논문집
• /
• 제34권6호
• /
• pp.85-92
• /
• 2014

This study carried out experimental on the cooling characteristics of clathrate compound including TMA(Tri-Methyl-Amine ; $(CH_3)_3N$) as a low temperature latent heat storage material. And additive was used for subcooling improvement of TMA-water clathrate compound. The conclusion of above study is as following ; TMA 25wt%-water clathrate compound is shown stable phase change and low subcooling degree. The subcooling was improved in the case ethanol($CH_3CH_2OH$) 0.5wt% is added to TMA 25wt%-water clathrate compound.