• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2001년도 춘계 학술대회논문집
• /
• pp.176-180
• /
• 2001

For windshield defrosting, flow analysis of inner room(vehicle) and heat conduction on the windshield surface are undertaken. Simulation for defrosting enthalpy method is usedand verification of heat and fluid flow analysis for room is done in cavity flow. The defrosting process is three dimensional phenomena and phase is changing. The result of defrosting analysis are well presenting the phase change and these results offer basic design data for defrosting phenomena.

• 설비공학논문집
• /
• 제17권3호
• /
• pp.201-208
• /
• 2005

This study presents the experimental study on improvement of frost/defrost performance in an heat pump system with newly developed fin and multiple compressors. As multiple compressors system, the variable and single speed compressor combinations has been introduced and compared with single speed 1-compressor system in a view point of improvement of frost/defrost performance. Also, newly developed corrugate shaped fin has been compared with conventional louver shaped fin. The frost/defrost performance is defined and some parameters are compared to discuss the effect of each combination. From this experimental study, it is known that if the variable and single speed compressor combination system equipped with corrugate shaped fin, the system performance has greatly improved not only for heating capacity, but also for frost performance.

• 설비공학논문집
• /
• 제26권9호
• /
• pp.434-440
• /
• 2014

Experiments were performed to verify if performance and characteristic curves obtained from the temperature differential defrosting method, where surface temperature is measured to judge defrosting condition, can be reproduced by the photoelectric technology where defrosting condition is judged by photoelectric sensors. The output voltage of a phototransistor and heating capacity, power consumption, and surface temperature of the outdoor heat exchanger are compared. The results showed that the photoelectric sensors can be used as a defrost control device. On-off control timings in temperature differential defrosting method are in good agreement with those predicted by the high and low threshold output voltages of the photoelectric sensor.

• 설비공학논문집
• /
• 제15권3호
• /
• pp.196-202
• /
• 2003

Two dimensional modeling was carried out to find the safety distance between the defrost heater and the plastic inner wall of domestic refrigerator Estimation was processed for the three cases; the estimation of plastic wall temperature (1) without any protection, (2) with an aluminum foil attached on a wall, and (3) with an aluminum shield installed between heater and wall. The former two cases are found to be dangerous during defrosting process, because the temperatures of inner wall reach above 80'C , which is the upper temperature limit of the wall material. The case with an aluminum shield is considered to be safe by maintaining the temperature of the wall in the range of 6$0^{\circ}C$ during defrosting process.

• 한국자동차공학회논문집
• /
• 제11권2호
• /
• pp.157-163
• /
• 2003

This work was undertaken for the numerical analysis of defrosting phenomena of automobile windshield. To analyze the defrost, the flow and temperature field of cabin interior, heat transfer through the windshield glass, and phase change of the frost should be analyzed simultaneously. The flow field was obtained by solving the 3-D unsteady Navier-Stokes equation and the temperature field was computed by energy equation. The phase-change process of Stefan problem was solved by enthalpy method. For code validation, the temperature field of the driven cavity was calculated. The result of calculation shows a good agreement with the other numerical results. Then, the present code was applied to the defrosting analysis of a real automobile and, also, a good agreement with experiment was obtained.

• 한국산학기술학회논문지
• /
• 제15권6호
• /
• pp.3389-3395
• /
• 2014

제상제어 수단으로 사용하고 있는 일정 시간 제어방식, 온도차 제어방식 등은 종종 제상 오작동과 에너지 낭비를 가져오므로 좀 더 정확하게 제상을 제어할 수 있는 방법이 요구되고 있다. 수광부와 발광부로 구성된 광센서를 실외 열교환기 전방에 설치하여 서리의 유무에 따른 출력전압의 변화를 관찰함으로서 정확하게 제상제어를 할 수 있다. 본 연구에서는 기존의 일정시간 제상 방법을 사용하는 경우 나타나는 시스템 성능 및 특성 곡선을 광센서를 사용하여 재현가능한지 판단하기 위해 KS C 9306에 따른 난방 제상능력 시험조건(건구온도 $2^{\circ}C$/습구온도 $1^{\circ}C$)에서 실험을 수행하였다. 실험을 통해 측정한 난방능력, 소비전력, 열교환기 표면온도와 광센서 수광부 출력전압을 비교, 분석한 결과 제상 제어수단으로 광센서의 사용가능성을 확인하였다. 일정시간 제상방법을 통해 구한 제상 제어 단속 주기는 광센서를 통해 측정한 출력 전압의 단속 주기와 잘 일치하였다.

• International Journal of Air-Conditioning and Refrigeration
• /
• 제13권3호
• /
• pp.152-157
• /
• 2005

This paper reviews the literature on the performance of fin-and-tube heat exchangers under frosting and defrosting conditions. The effects of frosting and defrosting on the following parameters were discussed: frost growth, overall heat transfer coefficient, surface roughness, and surface characteristics on the heat exchanger. Comparisons of the experimental results and empirical correlations that were obtained from open literature were presented. In addition, a review of the defrosting methods was conducted.

• 한국산학기술학회논문지
• /
• 제14권2호
• /
• pp.573-577
• /
• 2013

히트펌프는 에너지 효율이 높고, 지열, 폐열, 공기열 등 다양한 열원 사용이 가능하기 때문에 보급이 빠르게 확대되고 있다. 공기를 열원으로 이용하는 공랭식 히트펌프의 경우는 실외기 표면에 형성되는 서리를 제거하기 위해 제상운전이 요구된다. 일반적으로 사용하는 역사이클(reverse cycle) 제상운전 방법은 연속난방이 불가능하며 이로 인해 성능계수가 감소하는 원인이 된다. 본 연구에서는 실외기 코일용 휜-관 열교환기를 3열로 구성하고 난방과 제상이동시에 가능하도록 일정시간 간격으로 열교환기의 한 개의 열을 응축기로, 나머지 열은 증발기로 교번 운전을 수행하여 KS C 9306에 규정된 제상-난방 시험조건(건구온도 $2^{\circ}C$, 습구온도 $1^{\circ}C$)에서 최소 180분 이상 연속난방이 가능함을 실증하였으며 역사이클 제상방법을 사용하는 일반적인 히트펌프 대비 COP가 약 20% 향상됨을 알 수 있었다.

• 대한기계학회논문집 C: 기술과 교육
• /
• 제3권1호
• /
• pp.1-13
• /
• 2015

실외 열교환기의 착상 및 제상조건 하에서 VRF 멀티형 히트펌프의 동적 거동의 해석을 위한 시뮬레이션 기법이 제안되었다. 이를 위해 열전달-물질전달 완벽 상사 가정에 기반한 간단한 착상모델과 제상 모델이 제안되었다. 제안된 착제상 모델은 용량가변 압축기 모델과, 미소면적에 대한 열 및 모멘텀 평형에 근거한 열교환기 모델을 채택한 동적 사이클 해석모델에 적용되었다. 따라서, 제안된 모델은 공간에 대해 비균질 착상을 자연스럽게 예측할 수 있다. 개발된 동적 사이클 해석 모델은 실험결과와 비교하여 능력 및 효율을 10% 이내에서 잘 예측함을 확인하였다. 최종적으로, 개발된 모델은 표준적인 건물의 난방시즌 운전 해석에 적용되었으며, 착상 및 제상으로 인하여 동절기의 계절 성능계수를 7% 가량 하락 시킴을 보일 수 있었다.

• 동력기계공학회지
• /
• 제14권4호
• /
• pp.5-10
• /
• 2010

This study was investigated the effect on operating characteristics of apparatus according to frosting and defrosting to develop of new defrosting equipment. The results showed as following. Frost was almost removed using the defrosting equipment with roll brush type that defrosting is possible under operating condition. Also, the temperature of compressor inlet, evaporator inlet and outlet showed higher value because of heat transfer resistance of cooling pipe frost comparing with defrosting condition. And the compressor work showed 10% lower and COP was presented 24% higher values than defrosting condition. Therefore, defrosting for cooling coil of refrigeration and low temperature storage was effected on operation and performance characteristics of equipment. This highly effects on real refrigeration apparatus which is operated in year-around.