• Journal of the korean academy of Pediatric Dentistry
• /
• v.32 no.4
• /
• pp.657-661
• /
• 2005

Various chemotherapeutic agents have been recommended for pulpotomy of primary teeth, and there are formocresol, ferric sulfate, and calcium hydroxide. Of those, formocresol has fixation effect of pulp tissue and high clinical success rate, so it is most commonly used agent. But formocresol has strong cytotoxic effects, thus many articles reported displacement and loss of permanent successor, amelogenesis imperfecta, mutation by general absorption, possibility of cancer induction. Recently, it has been reported that leakage by imperfect temporary sealing when FC-soaked cotton was inserted into the root canal caused necrosis of surrounding tissues. and that necrosis of alveolar bone related to the use of excessive formocresol. In this case, 2nd primary molar of upper left jaw was treated using formocresol in local clinic, but extracted because of lasting pain. Furthermore, symptoms didn't disappear so patient was refered to us. The patient was 8-year-old male, had foul odor from oral cavity and circular alveolar bone necrosis around the permanent successor' crown. Thus sequestrectomy was operated and observed through 19 months after operation, we found normal root development of permanent successor but no complete regeneration of alveolar bone defect and attached gingiva. Lesion of periodontal tissues by formocresol is irreversible, so we have to confirm the indication in using formocresol and pay attention to complete temporary sealing.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.28 no.1
• /
• pp.40-45
• /
• 2015

Electrode systems: a protrusion on conductor (POC), a protrusion on enclosure (POE), a crack in epoxy plate and a free particle (FP) were fabricated to simulate insulation defects in a gas insulated switchgear (GIS). $SF_6$ gas was filled in the electrode systems by 3 bar and/or 5 bar, respectively. Partial discharge (PD) pulses were detected through a $50{\Omega}$ non-inductive resistor. A calibration test was carried out according to IEC 60270, and the sensitivity was 0.25 pC/mV. PD pulses were distributed in the phase of $50^{\circ}{\sim}135^{\circ}$ and over 95% of them existed in the phase of $55^{\circ}{\sim}120^{\circ}$ for the POC. PD pulses were distributed in the phase of $230^{\circ}{\sim}310^{\circ}$ and over 90% of them existed in phase of $220^{\circ}{\sim}300^{\circ}$ for the POE. PD pulses occurred in the phase of $40^{\circ}{\sim}60^{\circ}$ and $220^{\circ}{\sim}300^{\circ}$ for the crack, and pulse counts were 25% higher in negative polarity than in positive polarity. PD pulses were distributed in every phase unlike to other three electrode systems and the peak magnitude was measured at $118^{\circ}$ and $260^{\circ}$ for the FP. As described above, PD pulses were observed in positive polarity for the POC, in negative one for the POE, in both one for the crack and the FP. In conclusion, it is expected that the identification rate of defect type can be improved by considering the polarity ratio of PD pulses on the PRPDA method.

• Korean Journal of Crystallography
• /
• v.4 no.2
• /
• pp.74-85
• /
• 1993

Single crystals of LiNbO3 have found extensive application in electro-optic and nonlinear optic devices. However, laser-induced refartive index inhomogeneities, which have been labeled opical damage impose limits on device optical damage in LiNbO3 is imporved if more than 4.5 rml% MgO is added to the melt The laser damage thrueshold increased as much as 100 times better then that of undoped crystals. The MgO doped cystal has thus been urterlsiv81y studied since then. In the study, Mgo:LiNbOs(MLA) single crystals dopsd with 0, 2.5, 5.0, 7.5, 10.0 mol% MgO have been grown by the czocrualski technique. The metls were prepared in the platinum crluible and 15∼20mm diameter crystals were grown with a length of 20∼30mm in a resitance heater. The growth rate was 2.5mm/hr, the rotation speed 15rpn. Before sawing MLN single crystals were annealed for 24 hours under atmosphere at a temperature of 1080℃. After sawing, we have found an annual ring cross section of MNA crystals only in the direction of perpendicilar to the c-axis. Nonuniform dispusion of MgO was pointed out that the cuties of the state of oxide were strongly affected by oxygen partial pressure in.

• Journal of the Korea Concrete Institute
• /
• v.25 no.2
• /
• pp.209-215
• /
• 2013

This study is aimed to identify the method to use the CaO-$Al_2O_3$ system of rapidly cooled steel making slag (RCSS) as the environment-friendly inorganic accelerating agent by analyzing its physical and chemical properties. The fraction of rapidly cooled steel making slag is distinguished from its fibrous, and the contents of CaO and $Fe_2O_3$ are inversely proportional across different fractions. In addition, as the content of CaO decreased and the content of $Fe_2O_3$ increased, the loss ignition tended to become negative (-) and the density increased. The pore distribution by mercury intrusion porosimetry is very low as compared to the slowly cooled steel-making slag, which indicates that the internal defect and the microspore rate are remarkably lowered by the rapid cooling. To analyze the major minerals the rapidly cooled steel-making slag, XRD, f-CaO quantification and SEM-EDAX analysis have been performed. The results shows that f-CaO does not exist, and the components are mainly consisted of $C_{12}A_7$ and reactive ${\beta}-C_2S$.

• Maxillofacial Plastic and Reconstructive Surgery
• /
• v.27 no.2
• /
• pp.103-109
• /
• 2005

In spite of the ongoing advances, standard therapies for oral cancer still has some limitations in efficacy and in ability to prolong survival rate of advanced disease and result in significant functional defect and severe cosmetic deformity. Currently gene therapy using tumor suppressor gene is considered as a potent candidate for new therapeutic approaches that can improve efficacy and reduce complications. The purpose of this research is to identify the role of adenoviral vector to transfer HCCS-1 tumor suppressor gene in oral cancer cells and to find out whether there is a possibility for it to serve in the field of gene therapy. The human SCC-25 cell line was used for transfection. To determine the efficiency of the adenovirus as a gene delivery vector cell line was transduced with LacZ gene and analysed with X-gal staining. Northern blot was performed to confirm the tranfection with HSCC-1 gene and cell viability was assessed by cell cytotoxicity assay. We had successfully construct the recombinant HSCC-1 adenovirus(Ad5CMV-HCCS-1). DNA extracted from Ad5CMV-HCCS-1 revealed HCCS-1 gene is incorporated. The transduction efficiencies were over than 50% of SCC-25 cells with a MOI of 2 and over 95% with a MOI of 50. Northern blot analysis showed that a single 0.6kb mRNA transcript was expressed in Ad5CMV-HCCS-1 transduced SCC-25 cells. There was no or very low transcription HCCS-1 mRNA in wild and Ad5CMV-LacZ transduced SCC-25 cells. Cells transduced with Ad5CMV-HCCS-1 showed significant growth inhibition. By day 6, Ad5CMV-HCCS-1 treated cell count was decreased to 30% of mock-infected cells, while that of Ad5CMV-LacZ treated cells was 90% of mock-infected cells (p<0.05). Finally, these result suggest that the Ad5CMV-HCCS-1 has potential as a gene therapy tool for oral cancer.

• Journal of IKEEE
• /
• v.24 no.1
• /
• pp.25-32
• /
• 2020

In this paper, we propose an image generator for OLED panel test that can compensate for color coordinates and luminance by using panel defect inspection and optical measurement while displaying images on OLED panel. The proposed image generator consists of two processes: the image generation process and the process of compensating color coordinates and luminance using optical measurement. In the image generating process, the panel is set to receive the panel information to drive the panel, and the image is output by adjusting the output setting of the image generator according to the panel information. The output form of the image is configured by digital RGB method. The pattern generation algorithm inside the image generator outputs color and gray image data by transmitting color data to a 24-bit data line based on a synchronization signal according to the resolution of the panel. The process of compensating color coordinates and luminance using optical measurement outputs an image to an OLED panel in an image generator, and compensates for a portion where color coordinates and luminance data measured by an optical module differ from reference data. To evaluate the accuracy of the image generator for the OLED panel test proposed in this paper, Xilinx's Spartan 6 series XC6SLX25-FG484 FPGA was used and the design tool was ISE 14.5. The output of the image generation process was confirmed that the target setting value and the simulation result value for the digital RGB output using the oscilloscope matched. Compensating the color coordinates and luminance using optical measurements showed accuracy within the error rate suggested by the panel manufacturer.

• Journal of the Korean Institute of Landscape Architecture
• /
• v.39 no.2
• /
• pp.91-102
• /
• 2011

This study was carried out to analyze the problems on several steps of the establishment of the Nature Ecological Forest in Yeouido Park, Seoul, and also to suggest improved approaches on each step. For execution drawing, planting models and plans seemed to be uncertain, and the quantity and size of planting trees seemed to be impractical. For construction, the woody plants planted on the site were different in species and size from the planting plan. Ecological planting was somewhat limited because of the inappropriate soil properties. For management, replacement of the dead trees was not executed properly, and no management scheme was prepared after the replacement period. We suggested improved approaches for the establishment of ecological forests in urban areas as follows: for execution drawing, overstory, understory and herbaceous ground cover layers should be composed based on standard plant community structures. Trees that are available from tree markets should be specified in the planting plan. For construction, trees for planting need to be tagged to identify species and size. When tree species and size are changed, they should be checked to ensure that they are proper to the plant community model. Soil information should be collected to check that they fit the target plant community model. For management, the proper amount of trees needs to be specified in the planting plan by applying regular discount rates, especially for trees supplied from the government sector. The replacement period should be extended from two years to five years. The change of plant communities should be monitored during first five years after establishment.

• Spatial Information Research
• /
• v.12 no.2
• /
• pp.181-191
• /
• 2004

Nowadays, GPS-photogrammetry can be applied to the basemap production, a land register and NGIS. And from now on, as the increase of GPS receiver rate, the study on the interpolation methods considering the exact movement of an aircraft at photoflight and the study on the supplement of GPS defect by INS are required continuously. GPS-Photogrammetry, which are based on the direct measurement of the projection centers and attitude at the moment of camera exposure time through loading the GPS receiver in aircraft. This photogrammetric methods can of for us to acquire the exterior orientation parameters with only minimum ground control points, even the ground control process could be completely skipped. Consequently, we can drastically reduce the time and cost far the mapping process. In this thesis, two test flights were conducted in area to evaluate the performance of accuracy and efficiency through the analysis of results between the two photogrammetric methods, that is, traditional photograrammetry, GPS-Photogrammetry. Test results shows that a large variety of advantages of GPS-Photogrammetry against traditional photogrammetry is to be verified. Especially, the number of ground control points for the exterior orientation could be saved more than 70～80%, and the cost far map production 30～50%, respectively. In addition, it was convinced that the large reduction of control points has not any effect on the block accuracy.

• Journal of Life Science
• /
• v.26 no.8
• /
• pp.921-927
• /
• 2016

Postprandial hyperglycemia is an early defect of type 2 diabetes and one of primary anti-diabetic targets. The alpha-glucosidase inhibitors regulate postprandial hyperglycemia by impeding the rate of carbohydrate (such as starch) digestion in the small intestine. This study was designed to investigate the inhibitory actions of mulberry fruit extract (MFE) on α-glucosidase and α-amylase activities, and its alleviating effect on postprandial hyperglycemia activities in vitro and in vivo. Male four-week old ICR mice and streptozotocin (STZ)-induced diabetic mice were treated with mulberry fruit extract. MFE showed strong inhibitory effects against α-glucosidase and α-amylase activities, with half-maximal inhibitory concentration (IC₅₀) values of 0.16 and 0.14 mg/ml, respectively, and was more effective than acarbose, which was used as a positive control. The increase in postprandial blood glucose levels was more significantly attenuated in the MFE-administered group mice than in the control group mice of both STZ-induced diabetic and normal mice. Moreover, the area under the glucose response curve significantly decreased following MFE administration in diabetic mice. These results indicate that MFE may be a potent inhibitor of α-glucosidase and α-amylase, and helpful in suppressing postprandial hyperglycemia in diabetic mice. The mulberry fruit extracts may be considered as a potential candidate for the management of diabetes.

• Journal of Chest Surgery
• /
• v.32 no.3
• /
• pp.287-293
• /
• 1999

Background: Medical treatment of multiple drug resistant(MDR) pulmonary tuberculosis has been quite unsuccessful. We analyzed our experience to identify the benefits and complications of the pulmonary resection in MDR pulmonary tuberculosis. Material and Method: A retrospective review was performed in 27 patients who unerwent pulmonary resection for MDR pulmonary tuberculosis between January 1994 and March 1998. Mean age was 40 years and the average history of diagnosis prior to surgery was 3.1 years. All had resistance to an average of 4.4 drugs, and received second line drugs selected according to the drug sensitivity test. Most patients (93%) had cavitary lesions as the main focus. Bilateral lesions were identified in 19 patients (70%), however, the main focus was recognized in one side of the lung. Eleven patients (41%) were converted to negative sputum smear and/or culture before surgery. Result: Pneumonectomy was performed in 9 patients, lobectomy in 16 and segmentectomy in 2. There was no operative mortality. Morbidity had occurred in 7 patients (26%), prolonged air leak in 3 patients, reoperation due to bleeding in 2, bronchopleural fistula in 1, and reversible neurologic defect in 1. Median follow up period was 15 months (3-45 months). Sputum negative conversion was initially achieved in 22 patients (82%), and with continuous postopertive chemotherapy negative conversion was achieved in other 4 patients (14%). Only one pneumonectized patient (4%) failed due to considerable contralateral cavity. Conclusion: For patients with localized MDR pulmonary tuberculosis and with adequate pulmonary reserve function, surgical pulmonary resection combined with appropriate pre and postoperative anti-tuberculosis chemotherapy can achieve high success rate with acceptable morbidity.