• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.15 no.10
• /
• pp.838-843
• /
• 2002

Chemical mechanical polishing(CMP) process has been widely used to planarize dielectric layers, which can be applied to the integrated circuits for deep sub-micron technology. The reverse moat etch process has been used for the shallow trench isolation(STI)-chemical mechanical polishing(CMP) process with conventional low selectivity slurries. Thus, the process became more complex, and the defects were seriously increased. In this paper, we studied the direct STI-CMP process without reverse moat etch step using high selectivity slurry(HSS). As our experimental results show, it was possible to achieve a global planarization without the complicated reverse moat process, the STI-CMP process could be dramatically simplified, and the defect level was reduced. Therefore the throughput, yield, and stability in the ULSI semiconductor device fabrication could be greatly improved.

• Proceedings of the Korean Vacuum Society Conference
• /
• 1999.07a
• /
• pp.81-81
• /
• 1999

고에너지 이온 주입에 의해 형성되는 결함의 거동을 DLTS(deep level transient spectroscopy)를 통해 조사하였다. 이온 주입에 이용된 기판들은 서로 다른 산소 농도를 가지고 있었으며, B 이온의 주입 농도는 각각 5X10E13 ~ 4X10E14으로 주입 에너지는 1.5MeV였다. 이온 주입에 의해 형성된 buried layer 내의 boron의 농도는 SIMS(secondary ion mass spectroscopy)를 이용하여 측정하였으며, 열처리에 따른 이차 결함의 생성은 TEM(transmission electron microscopy) 및 BMD(bulk micro defect)를 조사함으로써 알 수 있었다. 이온 주입에 의해 형성된 일차 결함의 제거 및 silicon 내부에서의 금속 gettering을 위하여 furnace 및 RTA (rapid thermal annealing)를 이용한 열처리를 행하였다. 이온주입 초기 상태 및 산소의 농도 또는 이온주입의 농도에 따른 결함을 살펴보기 위하여 DLTS를 이용하였으며, 또한 열처리에 따른 이러한 초기 결함들의 거동을 조사하여 TEM 및 BMD 결과와 비교, 분석하였다.

• Journal of Periodontal and Implant Science
• /
• v.38 no.sup2
• /
• pp.405-412
• /
• 2008

Purpose: Pathologic tooth migration (PTM) commonly occurs in the anterior region and is associated with periodontal disease. The treatment of PTM of anterior teeth can be complex and time consuming, and a multidisciplinary approach is often required. Materials and Methods: The patient was a 38-year-old woman with a chief complaint of saving and realigning her elongated maxillary left central incisor. This paper describes the successful combined periodontal regenerative (guided tissue regeneration) and prosthetic treatment and a 2-year follow-up of maxillary central incisor with pathologic tooth migration, deep intrabony defect, and poor prognosis. Results: The right maxillary central incisor was restored by laminate veneer and the left by all-ceramic crown. The patient had no pain and discomfort and was satisfied with the outcomes of her treatment for 2 years. She has maintained her recall program at the Department of Periodontology at 3 months interval. Conclusion: The key step in the successful treatment of PTM in anterior region is to obtain a high level of cooperation from the patient. Maintenance of the treatment result of PTM is dependent on the continuous preservation of periodontal health.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2007.08a
• /
• pp.513-516
• /
• 2007

We introduce a new copolymer alignment film made by bridge-building structure. It is a better film to decrease the image-sticking level in LCD displays. It is noted that the image-sticking was decreased by preventing ion mixing between inter-layers through high hardness. We have investigated the electrical characteristics such as pretilt angle, Residual DC, VHR by changing cure temperature and process delay time conditions of the new alignment film. In this paper, we have investigated the solution for the deep-rooted image defect and incidentally got a contrast ratio improvement by high anchoring force and hardness elevation through the new copolymer alignment film.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.17 no.7
• /
• pp.764-769
• /
• 2004

In order to reduce operating voltage of the GaN based blue-violet laser diodes, the effect of highly Mg doped GaN layer, which was grown below ohmic contact metals, on contact resistivity as well as operating voltage has been investigated. The addition of the highly Mg doped GaN layer greatly reduced contact resistivity of Pd/Pt/Au ohmic contacts from $5.2 \times {10}^-2 \Omegaㆍ$\textrm{cm}^2$ to 7.5 \times {10}^-4 \Omegaㆍ$\textrm{cm}^2$$. In addition, it also decreased device voltage at 20 mA by more than 3 V. Temperature- dependent sheet resistivity of the highly Mg doped GaN layer suggested that the reduction of the contact resistivity could be attributed to predominant current flow at the interface between the Pd/Pt/Au contacts and p-GaN through a deep level defect band, rather than the valence band.

• Journal of the Korean Vacuum Society
• /
• v.18 no.2
• /
• pp.127-132
• /
• 2009

We have investigated the intrinsic defects remaining in epitaxial GaSb layers grown on SI-GaAs substrates compared to those in bulk GaSb crystal substrate, which is a basic material of Sb-based strained-layer superlattice infrared photodetectors. From the functional dependence of the band-to-band transition energy of the photomuminescence (PL) spectra observing up to near room-temperature (250 K), the temperature parameters of [$E_o$, $\alpha$, $\beta$] of undoped GaSb crystal are determined by using the Varshni empirical equation describing the temperature variation of the bandgap energy. Additionally to the antisite-Ga ([$Ga_{Sb}$]) with an ionization energy of 29 meV that is well known to a major intrinsic defect in GaSb, epitaxial GaSb layers show a pair of deep states at the emission energy of 732/711 meV that may be related with a complex of two antisite-Ga and antisite-Sb ([$Ga_{Sb}-Sb_{Ga}$]). Based on the analysis of the temperature and the excitation-power dependences of PL, it suggests that excess-Sb substitutes Ga-site by self-diffusion and two anti sites of [$Ga_{Sb}$] and [$Sb_{Ga}$] could form as a complex of [$Ga_{Sb}-Sb_{Ga}$] in GaSb epilayers grown under Sb-rich condition.

• Korean Journal of Materials Research
• /
• v.13 no.6
• /
• pp.347-351
• /
• 2003

II-Ⅵ ZnO compound semiconductor thin films were grown on $\alpha$-Al$_2$O$_3$(0001) single crystal substrate by radical beam assisted molecular beam epitaxy and the optical properties were investigated. Zn(6N) was evaporated using Knudsen cell and O radical was assisted at the partial pressure of 1$\times$10$^{4}$ Torr and radical beam source of 250-450 W RF power. In $\theta$-2$\theta$ x-ray diffraction analysis, ZnO thin film with 500 nm thickness showed only ZnO(0002)and ZnO(0004) peaks is believed to be well grown along c-axis orientation. Photoluminescence (PL) measurement using He-Cd ($\lambda$=325 nm) laser is obtained in the temperature range of 9 K-300 K. At 9 K and 300 K, only near band edge (NBE) is observed and the FWHM's of PL peak of the ZnO deposited at 450 RF power are 45 meV and 145 meV respectively. From no observation of any weak deep level peak even at room temperature PL, the ZnO grains are regarded to contain very low defect density and impurity to cause the deep-level defects. The peak position of free exciton showed slightly red-shift as temperature was increased, and from this result the binding energy of free exciton can be experimentally determined as much as $58\pm$0.5 meV, which is very closed to that of ZnO bulk. By van der Pauw 4-point probe measurement, the grown ZnO is proved to be n-type with the electron concentration($n_{e}$ ) $1.69$\times$10^{18}$$cm^3$, mobility($\mu$) $-12.3\textrm{cm}^2$/Vㆍs, and resistivity($\rho$) 0.30 $\Omega$$\cdot$cm.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.28 no.5
• /
• pp.291-294
• /
• 2015

Recently, ZnO based oxide TFTs used in the flexible and transparent display devices are widely studied. To apply to OLED display switching devices, electrical performance and stability are important issues. In this study, to improve these electrical properties, we fabricated TFTs having Al doped Zinc Oxide (AZO) layer inserted between the gate insulator and ZnO layer. The AZO and ZnO layers are deposited by Atomic layer deposition (ALD) method. I-V transfer characteristics and stability of the suggested devices are investigated under the positive gate bias condition while the channel defects are also analyzed by the photoluminescence spectrum. The TFTs with AZO layer show lower threshold voltage ($V_{th}$) and superior sub-threshold slop. In the case of $V_{th}$ shift after positive gate bias stress, the stability is also better than that of ZnO channel TFTs. This improvement is thought to be caused by the reduced defect density in AZO/ZnO stack devices, which can be confirmed by the photoluminescence spectrum analysis results where the defect related deep level emission of AZO is lower than that of ZnO layer.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.393-393
• /
• 2016

Cu(In,Ga)Se2 (CIGS) 박막 태양전지는 높은 효율과 낮은 제조비용, 높은 신뢰성으로 인해 박막 태양전지 중 가장 각광받고 있다. 특히 유리기판 대신 가볍고 유연한 철강소재나 플라스틱 소재를 이용하여 발전분야 외에 건물일체형, 수송용, 휴대용등 다양한 분야에 적용이 가능하다. 이러한 유연 기판을 이용한 CIGS 태양전지의 개발을 위해서는 기판의 특성에 따른 다양한 공정개발이 선행되어야 한다. Stainless steel과 같은 철강기판의 경우 Fe, Ni, Cr등의 불순물이 확산되어 흡수층의 특성을 저하시켜 효율을 감소시킨다. 따라서 이러한 철강 기판의 경우 불순물의 확산을 방지하는 확산방지막이 필수적이다. 이러한 유연기판의 특성을 고려하여 본 연구에서는 기존의 두껍고 추가 장비가 요구되는 SiOx나 Al2O3 대신 200nm 이하의 ZnO 박막을 이용하여 확산방지막을 제조하였다. 유연기판으로 STS 430 stainless steel을 이용하였다. 먼저 stainless steel 기판을 이용하여 기판에 의한 흡수층의 특성을 분석하였으며 ZnO 확산 방지막의 유무 및 두께에 따른 흡수층 및 소자의 특성을 분석하였다. 이때 확산 방지막은 기존 TCO 공정에서 사용되는 i-ZnO를 사용하였으며 RF sputter를 이용하여 50~200nm로 두께를 달리하며 특성 비교를 실시하였다. 효율은 확산방지막을 적용하지 않았을 때 약 5.9%에서 확산 방지막 적용시 약 10.7%로 증가하였다. 그 후 기판으로부터 확산되는 불순물의 유입에 의한 결함을 분석하기 위해 DLTS를 이용하여 소자 특성을 분석하였다. 온도는 80~300K으로 가변하며 측정을 실시하였으며 그 후 계산을 통해 activation energy와 capture cross section 값을 구하였다. DLTS 분석 결과 Ni이 CIGS 흡수층으로 확산되어 NiCu anti-site를 형성하여 태양전지의 효율을 감소시키는 것을 확인하였다. 모든 흡수층은 Co-Evaporation 방법을 이용하여 제조하였으며 제조된 흡수층은 SEM, XRF, XRD, GD-OES, PL, Raman등을 이용하여 분석하였으며 그 외 일반적인 방법을 이용하여 Mo, CdS, TCO, Al grid를 제조하였다. AR 코팅은 제외 하였으며 제조된 소자는 솔라 시뮬레이터를 이용하여 효율 특성 분석을 실시하였으며 Q.E. 분석을 실시하였다.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2010.06a
• /
• pp.338-338
• /
• 2010

지난 20여년 동안 반도체 레이저 다이오드는 주로 CD (DVD) 픽업용 (파장: 640 nm 이하) 및 통신용 (파장 1550 nm) 광원 분야에서 집중적으로 개발되어 왔다. 그러나 기술의 개발과 더불어 파장조절이 비교적 자유로워지고 광출력이 증대 되면서 기존의 레이저 고유의 영역까지 그 응용분야기 확대되고 있고, 이에 따라 고출력 반도체 레이저 다이오드의 시장 규모도 꾸준히 증가되고 있는 상황이다. 고출력 반도체 레이저 다이오드는 발진 파장 및 광출력에 따라 다양한 분야에 응용되고 있으며, 특히 발진파장이 808 nm 인 고출력 레이저 다이오드의 경우 재료가공, 펌핑용 광원 (DPSSL, 광섬유 레이저), 의료, 피부미용 (점 제거), 레이저 다이오드 디스플레이 등 가장 다양한 응용분야를 가진 광원 중의 하나라고 할 수 있다. MBE(Molecular Beam Epitaxy)로 성장된 InAlAs 에피층 (epi-layer)을 사용하여 고출력을 갚는 레이저 다이오드를 제작함에 있어서, 에피층은 결함 (defect)이 없는 우수한 단결정이 요구되지만, 실제 결정 성장 과정에서는 성장온도와 Al 조성비 등의 성장 조건의 변화에 따라 전기적 광학적 특성 및 신뢰성에 큰 영향을 받는 것으로 보고되고 있다. 이에 본 연구에서는 DLTS (Deep Level Transient Spectroscopy) 방법을 이용하여 InAlAs 양자점 에피층의 깊은 준위 거동을 조사하였다. DLTS 측정 결과, 0.3eV 부근의 point defect과 0.57 ~ 0.70 eV 영역의 trap이 조사되었으며, 이는 갈륨 (Ga) vacancy와 산소 원자의 복합체에 기인한 결함으로 분석된다.