• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.3 no.3
• /
• pp.639-650
• /
• 1999

In this paper, a chattering alleviation VSS controller for the sinusoidal type BLDC motor is designed. Dead Zone function is proposed to change the chattering occurring in the transient state from high frequency to low frequency and time-varying gains are applied for the control input to eliminate the steady state excessive chattering in the conventional ISM. The proposed Dead Zone function represents the sliding layer composed of two switching surfaces and if a state vector exists in this layer, the chattering don't occur. Simulation and experimental results confirm the useful effects of the above algorithm.

• Journal of Veterinary Clinics
• /
• v.39 no.3
• /
• pp.114-120
• /
• 2022

The purpose of this study is to examine the status of quality control using multipurpose phantom of ultrasound equipment used in hospital of veterinary college in South Korea by using ATS-539 multipurpose phantom so as to examine quantitative and objective new image evaluation method. Specialists discussed and analyzed multipurpose phantom images acquired by using convex transducer of 10 ultrasound imaging devices, currently used in 9 veterinary colleges, at 4.0-6.0 MHz. Total 8 items that can be measured with ATS-539 multipurpose phantom including dead zone, vertical and horizontal measurement, axial/lateral resolution, sensitivity, focal zone, functional resolution and gray scale/dynamic range were evaluated. For qualitative evaluation, valid decisions were made based on dead zone, axial/lateral resolution, and gray scale/dynamic range which are resolution index, and coefficient of variation (COV) and blind referenceless image spatial quality evaluator (BRISQUE) were found to increase objectivity. As a result of experiment, all the targeted ultrasonic devices were found appropriate from qualitative evaluation items of dead zone, axial/lateral resolution, and gray scale/dynamic range. In other evaluation items, they were found to be appropriate from focal zone and vertical measurement of quantitative evaluation while inappropriate from horizontal measurement, sensitivity, and functional resolution. COV value was 0.12 ± 0.04, and BRISQUE value was 47.77 ± 2.77, both analysis results show that the noise level of all ultrasonic devices was located within tolerance range. Upon image examination using ATS-539 multipurpose phantom, they were 100% appropriate with inspection standards of dead zone, axial/lateral resolution, and gray scale/dynamic range, and besides, focal zone and functional resolution can be used as evaluation items. In the field of veterinary medicine, 8 standard items using ATS-539 multipurpose phantom and image evaluation items using COV and BRISQUE can be used as standards for quality control of ultrasonography machine.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.10 no.4
• /
• pp.40-47
• /
• 2001

In this pater, the QLQG/LTR control method is applied for the position control of the nonlinear timing belt driving sys-tem. Parameters fo the plant are identified by genetic algorithm and nonlinear elements, such as Coulomb friction and dead-zone, and quasi-linearized by RIDE method. Comparing with the LQG/LTR contro. the QLQG/LTR has similar structures of the LQG/LTR, but this method can consider nonlinear effects in designing the controller. Thus, the QLQG/LTR control system is robust to hard nonlinearities such as Coulomb friction, dead-zone, etc. Forma given hard non-linear system through experiments, it is shown that the tracking performance of the QLQG/LTR control system can be very improved that the LQF/LTR control system.

• Journal of Electrical Engineering and Technology
• /
• v.9 no.4
• /
• pp.1324-1331
• /
• 2014

This paper proposes a compensation PWM technique for the extension of output voltage ranges in three-phase VSI applications using three shunt resistors. The proposed technique aims to solve the dead zone, which occurs in high modulation indexes. In the dead zone, two phase currents cannot be sampled correctly, so that the three-phase VSI cannot be operated up to the maximum output voltage. The dead zone is analyzed in detail, and the compensation PWM algorithm is developed. The proposed algorithm is verified by numerical analysis and experimental results.

• Journal of Electrical Engineering and Technology
• /
• v.13 no.5
• /
• pp.1996-2003
• /
• 2018

In this paper, the design and characteristic analysis of a novel single-phase hybrid switched reluctance motor (HSRM) for the purpose of replacing the universal motor in commercial blenders are presented. The proposed motor is easy to manufacture due to its simple yet robust structure with minimized power switches and no torque dead-zone. Moreover, the proposed HSRM is able to deliver a high starting torque as a requirement for blending hard food or even ice. The stator has permanent magnets (PMs) mounted on its inner surface and the rotor has a wide pole arc and salient poles that contribute to its high starting torque profile and the elimination of the torque dead-zone. Finite element method (FEM) is used to analyze the characteristic of the proposed motor. Finally, the prototype is manufactured and its performance is verified through experiments.

• Journal of the Semiconductor & Display Technology
• /
• v.22 no.4
• /
• pp.32-37
• /
• 2023

For the potential applications in large-area OLED lightings, hydrogen fuel cells, and secondary batteries, we have performed an intermittent coating of high-viscosity polydimethylsiloxane using roll-to-roll slot die coater. During intermittent coating, dead zones inevitably appear where the thickness of PDMS patch films becomes non-uniform, especially at the leading/trailing edge. To reduce it, we have coated the PDMS patches by varying the process parameters such as the installation angle of the slot die head, coating speed, and patch interval. It is observed that the PDMS solution flows down and thus the thickness profile is non-uniform for horizonal intermittent coating, whereas the PDMS solution remaining on the head lip causes an increase in the PDMS thickness at the leading/trailing edges for vertical intermittent coating when the coating velocity is low. As the coating speed increases, however, the dead zone is shown to be reduced. It is addressed that the overall dead zone (the dead zone at the leading edge + the dead zone at the trailing edge) is smaller with horizontal intermittent coating than with vertical intermittent coating.

• Proceedings of the IEEK Conference
• /
• 2008.06a
• /
• pp.715-716
• /
• 2008

A dead zone prediction system for vehicles are implemented in this paper. To improve performance reliability and stability, we import two method to get a information between car and car, and car and road. One is traffic lane detection method, another is vecle recognition. In this paper, we explain the methods and whole structure about this system except for details.

• Journal of the Institute of Electronics Engineers of Korea TE
• /
• v.39 no.3
• /
• pp.1-7
• /
• 2002

This paper presents a new PLL clock generator that can improve a jitter noise characteristics and acquisition process by designing a multi-PFD(Phase Frequency Detector) and an adaptive charge pump circuit. The conventional PLL has not only a jitter noise caused from such a demerit of the wide dead zone and duty cycle, but also a long delay interval that makes a high speed operation unable. An advanced multi-structured PFD circuit using the TSPC(True Single Phase Clocking) circuit is proposed, in which it shows an excellent functionalities in terms of the jitter noises by designing its circuit with the exact dead zone and duty cycle. Our new designed adaptive charge pump in the loop filter of a PLL can improve an acquisition characteristic by adaptively increasing of current. The Hspice simulation is done to evaluate the performance of the proposed circuit. Simulation result shows that our PLL has under 0.01ns in the dead zone, no influence from the duty cycle of input signals and under 50ns in the acquisition time. This circuit will be able to be used in develops of high-performance microprocessors and digital systems.  

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.36 no.3
• /
• pp.202-209
• /
• 2000

In order to estimate demersal fishes using acoustic echo sounders and echo integrators, we consider several problems that are accurate bottom detection, optimum bottom offset and dead zone. The dead zone where no fish detection are summed distance resolution by the half pulse length of transmitted pulse and beam angle above the seabed. This paper has considered the dead-zone correction method to be technically correct for survey of demersal fishes. A comparison between near-bottom SV profiles acquired in Funka Bay, Hokkaido, of Japan, the East China Sea and the Yellow Sea, of Korea, with before and after the bottom correction, shows that the SV obtained with after the bottom correction is 2∼3dB higher than before the bottom correction in Funka Bay, and 17dB higher in East China Sea, too.

• Journal of the HCI Society of Korea
• /
• v.12 no.1
• /
• pp.25-32
• /
• 2017

The purpose of this study is to evaluate the effectiveness of one-handed interaction modes for supporting the dead zone that users must be difficulty in performing the touch manipulation with only one hand. For the purpose, this study analyzed two existing one-handed modes in iPhone and Android smartphones, and proposed and implemented two additional one-handed modes. In order to investigate effectiveness of the one-handed modes, we performed the experiment that compared normal touch mode with the four one-handed modes. Experimental results showed that all one-handed modes required more time than normal touch mode because of the time requiring in both mode change and recognition. However, the participants had difficulty in manipulating continuous touches at dead zone area with only normal touch. Moreover, the subjective satisfaction was high in one-handed modes thanks to touch convenience and smooth transition effects in mode change. In special, the one-handed mode at iPhone was the most effective out of the tested modes.