• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.28 no.8
• /
• pp.54-61
• /
• 2014

This paper proposes a boost/flux-weakening controller (BFWC) for wide speed operation range having engine and interior permanent magnet synchronous generator (IPMSG) for special equipment vehicle. The proposed BFWC exploits direct torque/flux control (DTFC) scheme based on space vector modulation method to control the constant DC voltage output within the entire speed operation range of engine. And, to improve the response characteristics of maximum torque per ampere (MTPA) operation and flux-weakening operation, the MTPA and flux-weakening feed-forward controllers are applied. To estimate feasibility and usefulness of the proposed controller, the simulation and experimental results are compared.

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2008.05a
• /
• pp.70-73
• /
• 2008

Grounding impedance depends on the frequency of current flowing into a grounding system. Especially, the lightning gives a broad frequency spectrum from low frequency up to 1 MHz. So the grounding impedance related to high frequency current like lightning should be measured with high frequency source. In this paper, we described the grounding impedances of deeply-driven ground rods of 10 ${\sim}$ 48 m long with respect to the frequency of injected currents and the feed point. For the experiments, we used the wideband power amplifier which can produce sinusoidal voltages with the frequency ranges of DC ${\sim}$ 250 MHz. As a result, the longer the ground rod is, the lower the ground resistance is. However the grounding impedance of deeply-driven ground rod in the range of higher frequency is significantly increased. As a consequence, it is important to evaluate the high frequency performance of grounding systems for lightning protection.

• Journal of Power Electronics
• /
• v.12 no.2
• /
• pp.276-284
• /
• 2012

AC/AC power conversion is widely used to feed AC loads with a variable voltage and/or a variable frequency from a constant voltage constant frequency power grid or to connect critical loads to an unreliable power supply while delivering a very balanced and accurate sinusoidal voltage system of constant amplitude and frequency. The load specifications will clearly impose the requirements for the inverter stage of the power converter, while wider ranges of choices are available for the rectifier. This paper investigates the utilization of a buck-type current source rectifier as the active front-end stage of an AC/AC converter for applications that require an adjustable DC-link voltage as well as elimination of the low-frequency common mode voltage. The proposed solution is to utilize a combination of two or more zero current vectors in the Space Vector Modulation (SVM) technique for Current Sources Rectifiers (CSR).

• Journal of electromagnetic engineering and science
• /
• v.2 no.2
• /
• pp.93-99
• /
• 2002

The Cartesian loop chip which is one of key devices in narrow-band Walky-Talky transmitter using RZ-SSB modulation method was designed and implemented with 0.35 Um CMOS technology. The reduced size and low cost of transmitter were available by the use of direct-conversion and Cartesian loop chip, which improved the power efficiency and linearity of transmitting path. In addition, low power operation was possible through CMOS technology. The performance test results of transmitter showed -23 dBc improvement of IMD level and -30 dEc below suppression of SSB characteristic in the operation of Cartesian loop chip (closed-loop). At that time, the transmitting power was about 37 dBm (5 W). The main parameters to improve the transmitting characteristic and to compensate the distortion in feed back loop such as DC-offset, loop gain and phase value are interfaced with notebook PC to be controlled with S/W.

• Proceedings of the IEEK Conference
• /
• 2006.06a
• /
• pp.627-628
• /
• 2006

A low-voltage switched-capacitor $2^{nd}$-order $\Sigma\Delta$ modulator using full feed-forward is introduced. It has two advantages: the unity signal transfer function and reduced signal swings inside the $\Sigma\Delta$ loop. These features greatly relax the DC gain and output swing requirements for Op-Amp in the low-voltage $\Sigma\Delta$ modulator. Implemented by a 0.18-${\mu}m$ CMOS technology, the $\Sigma\Delta$ modulator satisfies performance requirements for WCDMA and CDMA2000 standards.

• Proceedings of the KIPE Conference
• /
• 2012.07a
• /
• pp.232-233
• /
• 2012

This paper presents an effective control scheme for an electric vehicle battery charger where a symmetrical bridgeless power factor-corrected converter and a buck converter are cascaded. Both converters have been popular in industries because of their high efficiency, low cost, and compact size, hence combining these converters makes the overall battery charging system strongly efficient. Moreover, this charger topology can operate at universal input voltage and attain a desired battery current and voltage without ripple. In order to achieve a unity input power factor and zero input current harmonic distortion, the proposed control scheme adopts duty ratio feed-forward control technique in both current and voltage control loop. Additionally, in the current loop, its reference is created by a phase-locked loop (PLL) block, leading to a pure sinusoidal input current although the input voltage waveform is being distorted. The feasibility and practical value of the proposed approach are verified by simulation and experiment with an 110V/60Hz ac line input and 1.5kW-72V dc output of the battery charging system.

• Journal of the Korean Society of Food Culture
• /
• v.17 no.4
• /
• pp.377-386
• /
• 2002

The purpose of this study was to investigate the effects of dietary Indongcho(L. japonica Thunb) powder on blood glucose, serum lipid levels and antioxidative enzymes in normal and streptozotocin(STZ)-induced diabetic rats. Four groups of rats(3-week-old inbred Sprague-Dawley male rats) were normal rats fed control diet(NC), diabetic rats fed control diet(DC), normal rats fed Indongcho powder diet(NI), and diabetic rats fed Indongcho powder diet(DI). Diabetes was induced by single injection of streptozotocin(60mg/kg B.W., i.p.). The animals were fed ad libium each of the experimental diet for 5 weeks. Food and water intakes were determined everyday. Blood glucose and serum total cholesterol levels were determined every week. After 5 weeks the animals were sacrificed and activities of antioxidant enzymes and lipid peroxidation products were determined in their liver and kidney homogenates. We also determined serum concentrations of total lipid(TL), total cholesterol(TC), triglycerides(TG) and HDL-cholesterol(HDL-C). Blood sugar and water intake were higher in diabetic group(DC and DI group) than normal group(NC and NI group) and were not significantly decreased by dietary Indongcho intake. Body weight gain and FER(feed efficiency ratio) were reduced by STZ treatment. But, Final body weight was recovered by Indongcho-contained diet. LHR(LDL-cholesterol/HDL-cholesterol) of the DI g re up was significantly lower than the other experimental groups(NC, NI and DC groups). The hepatic glucose 6-phosphatase(G6Pase) activity of the groups fed Indongcho diet(NI and DI group) was lower than the groups fed control diet(NC and DC group) and the G6Pase activity of NI group was recovered to the normal levels(p<0.05). However, The glutathione peroxidase(GPx) and glutathione reductase(GR) activities in liver and G6Pase activity in kidney were not statistically different between the control and diabetic control groups. Renal GST activity of the DI group was recovered by Indongcho intake. In conclusion, these results confirm oxidative stress in the liver and kidney of rats with STZ diabetes and antioxidative effect of Indongcho.

• Korean Journal of Veterinary Research
• /
• v.36 no.3
• /
• pp.541-550
• /
• 1996

Tetracycline antibiotics have been widely used not only therapeutics but feed additives. There are many methods for the isolation and determination of tetracycline antibiotics in animal muscle tissue. But those methods take much time and labor, so it is difficult to analyse many samples simultaneously. A rapid isolation method and liquid chromatographic determination of tetracycline antibiotics in animal muscle tissue (bovine, porcine, chicken) is presented. Blank control and tetracyclines fortified samples (0.5g) were blended with $C_{18}$ containing 0.05g each of oxalic acid and disodium ethylenediaminetetraacetate. After homogenize, homogenate was transferred to glass column made from 10ml glass syringe and compressed to 4~4.5ml volume. A column made from the $C_{18}$/meat matrix was washed with hexane (8ml) and dichloromethane (8ml, if needed), following which the tetracyclines were eluted,vith methanol or 0.01M methanolic oxalic acid (8ml). The eluates containing tetracyclines analytes were free from interfering compounds when analysed by HPLC with UV detection (photodiode array at 360nm). Standard curve for each tetracycline showed a linear response at the range of $0.05{\sim}1.0{\mu}g/ml$ and tetracycline antibiotics were eluted within 4ml of eluted volume. All tetracycline antibiotics except tetracycline were stable during the concentration process at $40^{\circ}C$ and time required for concentration was 3~4 hours. Fortified samples containing oxalic aicd and EDTA represented more good recoveries than those of not-contained sample. Recoveries were 91.8~110.1% (oxytetracycline; OTC), 57.7~79.5% (tetracycline; TC), 78.1~88.6% (chlortetracyclines; CTC) and 88.4~100.6% (doxycycline; DC) in pork tissue, 101.1~126.8% (OTC), 66.4~75.4% (TC), 79.2~88.1% (CTC) and 69.3~86.7% (DC) in beef tissue, and 90.8~95.6% (OTC), 66.2~84.4% (TC), 75.7~77.2% (CTC) and 55.6~80.7% (DC) in chicken muscle tissue. The detection limits validated in muscle tissue by this method were $0.05{\mu}g/g$ for OTC and TC, and $0.1{\mu}g/g$ for CTC and DC.

• Journal of The Korean Society of Grassland and Forage Science
• /
• v.17 no.2
• /
• pp.187-198
• /
• 1997

This experiment was conducted to evaluate effects of wilting and additives on fermetation characteristics, quality and aerobic stability of silage of rye(Seca1e cereale L.) harvested at the early heading stage. Harvested rye was wilted or mixed with beet pulp and then treated with formic acid or lactic acid bacteria(LAB) inoculant. Treatments were consisted of direct cut(DC), wilted(WT), beet pulp added(BP), direct cut and formate applied(DF), wilted and formate applied(WF), beet pulp and formate applied(BF), direct cut and LAB inoculated(DL), beet pulp added and LAB inoculated(BL), and wilted and LAB inoculated(WL) silages. Afler 70 days of ensiling period, the silages were opened and exposed to air for 7 days, and the silages of opening day(0 day) were compared with the silages exposed to air for 7 days(7 day). 1. LAB inoculated rye silages(DL, WL, BL) lowered pH values effectively eom the third day of ensiling and showed most stable pattern of pH changes during the initial fermentation process. Direct cut and formate applied(DF), beet pulp and formate applied(BF) and beet pulp added(BP) silages were also effective in lowering pH from the seventh day thai direct cut treatment(DC). 2. pH was low below 3.7 in all treatments of 0 day. After 7-day period of aerobic exposure, DL and WL showed considerable increases in pH from 3.5 and 3.4 to 8.3 and 6.4, respectively. 3. Direct cut rye silages(DF, DC, DL) and beet pulp and formate treatment(BF) produced effluent of 121.2, 85.9, 80.3 and 34.2 mlkg, respectively and these were greater than others(P<0.01). Beet pulp retained 1.61 I/kg of effluent at the application rate of 50 kg/t in comparing BP with DC, and formate application increased the amount of effluent in comparing DF and BF with DC and BP, respectively(P<0.01). 4. Beet pulp and LAB treatment(B1) was highest in content of lactate as 3.1% and formate treated silages(DF, WF, BF) showed lower content of lactate and total acid than others. LAB inoculated(D1, WL, BL) and wilted (WT) silages were graded to be good quality as a second group by the Flieg's score. Formate applied silages (DF, WF, BF) were graded as a foum group lower than DC by one. 5. Residual content of WSC of rye silage was higher in BP, BF, DL and BL than direct cut treatment(M3) (P< 0.01). Formate application had a tendency to increase the content of residual content of WSC. 6. For the ratio of NH3-N to Total N, wilted and LAB inoculated(W1) and direct cut and LAB inoculated(D1) silages were lowest on 0 day as 8.9 and 9.3% respectively. But after 7-day period of aerobic exposure, WL and DL showed largest increase of the ratio of $NH_3-N$ to Total N from 0 day(P<0.01). 7. On 0 day wilted(WT), beet pulp and formate treatment(BF), and beet pulp and LAB treatment(B1) were lower than direct cut treatment(DC) for NDF and ADF concentrations consistently. Formate applied silages (DF, WF, BF) made little change in ADF and NDF concentrations during 7 day period of aerobic exposure. DL and WL showed a large increase in ADF and NDF concentrations under aerobic condition(P<0.01). 8. IVDMD values of wilted(WT), beet pulp added(BP), wilted and LAB inoculated(W1) and beet pulp added and LAB inoculated(B1) silages were higher than direct-cut treatmentPC) as 84.7, 84.7, 84.4 and 83.0%, respectively on 0 day. But during 7-day period of aerobic exposure, a great decreae in IVDMD of WL was showed(P<0.01). The experimental results indicate that wilted silage(WT) could be recommended as the most effective treatment for reducing efluent and increasing quality and feed value of rye silage without deteriorating aerobic stability more than direct cut treatment(DC). Additionally, under unfavorable weather condition beet pulp added and LAB inoculated treatment(T3L) might be the possible alternative for successful ensiling of forage rye.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.27 no.9C
• /
• pp.871-878
• /
• 2002

The cartesian loop chip which is one of key devices in narrow-band Walky-Talky transmitter using RZ-SSB modulation method was designed and implemented with 0.35 ㎛ CMOS technology. The reduced size and low cost of transmitter were available by the use of direct-conversion and cartesian loop chip, which improved the power efficiency and linearity of transmitter. In addition, low power operation was possible through CMOS technology. The performance test results of transmitter showed -23㏈c improvement of IMD and -30㏈c below suppression of SSB characteristic in the operation of cartesian loop chip (closed-loop). At that time, the transmitting power was about 37㏈m (5W). The main parameters to improve the transmitting characteristic and to compensate the distortion in feed back loop such as DC-offset, loop gain and phase value are interfaced with notebook PC to be controlled with S/W.