• Journal of Engineering Education Research
• /
• v.6 no.1
• /
• pp.56-64
• /
• 2003

In this paper, we designed and implemented a client/server distributed environment and developed a web-based virtual laboratory system for electronic circuits. Since our virtual laboratory system is implemented to describe the on-campus laboratory, the learners can obtain similar experimental data through it. The proposed virtual laboratory system is composed of four important components : Principle Classroom, Virtual Experiment Classroom, Evaluation Classroom and Overall Management System. Through our virtual laboratory, the learners will be capable of learning the concepts and theories related to electronic circuit experiments and how to operate the experimental equipments such as multimeters, function generators, digital oscilloscopes and DC power supplies. Also, every experimental activity occurred in our virtual laboratory is recorded on database and printed out on the preliminary report form. All of these can be achieved by the aid of the Management System. The database connectivity on the web is made by PHP and the virtual labol'atory environment is set up slightly differently for each learner. Finally, we have obtained several affirmative effects such as reducing the total experimental hours and the damage rate for experimental equipments and increasing learning efficiencies as well as faculty productivity.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.9 no.2
• /
• pp.360-369
• /
• 2008

The solar cells should be operated at the maximum power point because its output characteristics were greatly fluctuated on the variation of insolation, temperature and load. It is necessary to install an inverter among electric power converts by means of the output power of solar cell is DC. The inverter is operated supply a sinusoidal current and voltage to the load and the interactive utility line. In this paper, the proposes a photovoltaic system is designed with a step up chopper and single phase PWM voltage source inverter. Synchronous signal and control signal was processed by one-chip microprocessor for stable modulation. The step up chopper is operated in continuous mode by adjusting the duty ratio so that the photovoltaic system tracks the maximum power point of solar cell without any influence on the variation of insolation and temperature for solar cell has typical dropping character. The single phase PWM voltage source inverter is consists of complex type of electric power converter to compensate for the defect, that is, solar cell cannot be develop continuously by connecting with the source of electric power for ordinary using. It can be cause the efect of saving electric power, from 10 to 20%. The single phase PWM voltage source inverter operates in situation, that its output voltage is in same phase with the utility voltage. The inverter are supplies an ac power with high factor and low level of harmonics to the load and the utility power system.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.38 no.3
• /
• pp.211-219
• /
• 2001

This paper describes a read-only CMOS transponder IC for RFID applications. A full-wave rectifier implemented using NMOS transistors supplies the transponder with a dc supply voltage using the magnetic field generated from a reader. A 64-bit ROM has been designed for a data memory. Front-end impedance modulation and Manchester coding are used for transmitting the data from the transponder memory to the reader. A new damping circuit which has almost constant damping rate under the variations of the distance between the transponder and the reader has been employed for impedance modulation. The designed circuit has been fabricated using a 0.65${\mu}{\textrm}{m}$2-poly, 2-metal CMOS process. Die area is 0.9mm$\times$0.4mm. Measurement results show that it has a constant damping rate of around 20~25% and a data transmission rate of 3.9kbps at a 125KHz RF carrier. The power required for reading operation is about 100㎼. The measured reading distance is around 7cm.

• Progress in Superconductivity and Cryogenics
• /
• v.23 no.4
• /
• pp.19-24
• /
• 2021

The low normal zone propagation velocity (NZPV) of high-temperature superconducting (HTS) tape leads to a quench protection problem in HTS magnet applications. To overcome this limitation, various studies were conducted on HTS coils without turn-to-turn insulation (NI coils) that can achieve self-protection. On the other hand, NI coils have some disadvantages such as slow charging and discharging time. Previously, the HTS coils with turn-to-turn insulation (INS coils) were operated in power supply (PS) driven mode, which requires physical contact with the external PS at room-temperature, not in persistent current mode. When a quench occurs in INS coils, the low NZPV delays quench detection and protection, thereby damaging the coils. However, the rotary HTS flux pump supplies the DC voltage to the superconducting circuit with INS coils in a non-contact manner, which causes the INS coils to operate in a persistent current mode, while enabling quench protection. In this paper, a new protection characteristic of HTS coils is investigated with INS coils charging through the rotary HTS flux pump. To experimentally verify the quench protection characteristic of the INS coil, we investigated the current magnitude of the superconducting circuit through a quench, which was intentionally generated by thermal disturbances in the INS coil under charging or steady state. Our results confirmed the protection characteristic of INS coils using a rotary HTS flux pump.

• Journal of Advanced Navigation Technology
• /
• v.28 no.3
• /
• pp.348-355
• /
• 2024

A current source capable of stably supplying current as a measurement medium is required in order to measure and test important facilities that require large-scale measurement current, such as a control element drive mechanism control system(CEDMCS), in case of dismantling a nuclear power plant. However, it can provides only voltage power as a source, not current, although direct voltage controlled constant current source is essential to test major equipment. That kind of source is not available to supply stable constant current regardless of load variation. It is just voltage supplier. Developing current source is not easy other than voltage source. Very large-scale current source up to ampere class more than such ten times of normal current is inevitable to test above mentioned equipment. So, we developed large-scale current source which is controlled by input DC voltage and supplies constant stable current to object equipment according to this requirement. We measured and tested nuclear power plant equipment using given real site data for a long time and afforded long period load test, and then proved its validity and verification. The developed invetion will be used future installed important equipment measuring and testing.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.34 no.1
• /
• pp.27-34
• /
• 2010

In a test duct with closed configuration, particle removal performance of an edge-plate type electrostatic precipitator (ESP) was evaluated at a high flow rate in $CO_2$ rich environments by changing gap distances between collection plates, concentrations of $CO_2$, particle sizes, types of electrodes, and types of power supplies. At the same experimental conditions, collection efficiency of particles with the mean particle size, 300 nm, decreased as the gap distance and $CO_2$ concentration increased because of low electrostatic force and low discharged current. In addition, as the particle size increased, the efficiency increased because of high charging rate of the large particles. With the electrode type which has higher surface area of a discharging plate and with the power supply which applied 25 kHz-pulsed DC voltages, the removal efficiency was high even in rich $CO_2$ condition due to high electrostatic force at the same power consumption.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.21 no.12
• /
• pp.1380-1393
• /
• 2010

This paper presents a design, fabrication and the test results of planar active electronically scanned array(AESA) radar prototype for airborne fighter applications using transmit/receive(T/R) module hybrid technology. LIG Nex1 developed a AESA radar prototype to obtain key technologies for airborne fighter's radar. The AESA radar prototype consists of a radiating array, T/R modules, a RF manifold, distributed power supplies, beam controllers, compact receivers with ADC(Analog-to-Digital Converter), a liquid-cooling unit, and an appropriate structure. The AESA antenna has a 590 mm-diameter, active-element area capable of containing 536 T/R modules. Each module is located to provide a triangle grid with $14.7\;mm{\times}19.5\;mm$ spacing among T/R modules. The array dissipates 1,554 watts, with a DC input of 2,310 watts when operated at the maximum transmit duty factor. The AESA radar prototype was tested on near-field chamber and the results become equal in expected beam pattern, providing the accurate and flexible control of antenna beam steering and beam shaping.