• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.14 no.9
• /
• pp.944-949
• /
• 2003

In this paper, the double balance mixer(DBM) for Ku-band LNB using InGaP/GaAs HBT process is suggested for the characteristics of low DC power consumption, low noise figure, low intermodulation distortion and wide dynamic range. The 5 dB conversion gain, 14 dB NF, bandwidth 17.9 GHz and 50.34 dBc IMD are obtained under RF input power of -23 dBm, with bias condition as 3 V and 16 mA. The linearity of InGaP/GaAs HBT, the broad band input matching scheme and the optimization of bias point result in the low IMD, the broad bandwidth and the low power consumption characteristics.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.16 no.9
• /
• pp.862-876
• /
• 1991

In this theses, the procedure for finding the equivalent immittance of an n-line coupled structures is presented in terms of the normal mode parameters of the n-line coupled system. The above generalized equations can be applied to the various Coupled structures including directional couplers, DC blocks, bandpass/band elimination filters, and various other uniformly coupled filters. The design equations are based on a simplified TEM(Quasi TEM) mode. The obtained results and the definition of the scattering parameters for a general coupled line four port with arbitrary terminations are used to present the procedure to determine the optimum physical dimensions matching the given load impedances connected to input, output port. Multiple coupled rnicrostrip two-port with three lines circuit designed shows little discrepancy between the conventional method and this one. Four port with five lines were fabricated on teflon substrate($e$r=2.55) with its thickness h=l.588mm designed at the center frequency, 4 GHz. Their measured results are fairly close to the ones by computation.

• Applied Microscopy
• /
• v.34 no.1
• /
• pp.51-59
• /
• 2004

The high acceleration voltage system used in scanning electron microscope were designed and manufactured to test its stability. The Cockcroft-Walton circuits are used both in the cathode voltage up to -30 kV and in the Wehnelt cylinder of -2 kV. The operating voltage of 6 V was applied to the heating of the filament. The wave forms which are formed in the second leg of the high voltage transformer were observed in the oscilloscope with 2 V of DC input. When the high voltages were in the range between 5 kV and 12 kV, the highest value of the stabilities of the generated voltages was obtained as 0.002%.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.40 no.2
• /
• pp.355-362
• /
• 2015

In this study, we have fabricated 9.385[GHz] circulator that is composed of WR112 waveguide and Ferrite for X-band radar. For designing Ferrite, B/R mode(Below Resonance mode) was used and calculated the condition of 120 degree rotation of the electric field in Ferrite and calculated internal DC magnetic field and external DC magnetic field. Also, dielectric materials of the same shape with Ferrite was filled between two Ferrite for improving the performance of the circulator, including impedance matching, bandwidth, quality factor, insertion loss. To obtain optimum shape of the Ferrite and dielectric material, we used CST MWS. Simulation result of the circulator is that 1.02 : 1 VSWR, -40dB isolation, 0.2dB insertion loss and measurement result is that 1.03 : 1, -38dB, 1.2dB at 9.385[GHz]. We can get good agreement at isolation and VSWR, but insertion loss was 1 dB great than simulation result.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.17 no.11 s.114
• /
• pp.1105-1111
• /
• 2006

In this paper, using low-temperature co-fired ceramic(LTCC) based system-in-package(SiP) technology, a very compact power amplifier LTCC module was designed, fabricated, and then characterized for 60 GHz wireless transmitter applications. In order to reduce the interconnection loss between a LTCC board and power amplifier monolithic microwave integrated circuits(MMIC), bond-wire transitions were optimized and high-isolated module structure was proposed to integrate the power amplifier MMIC into LTCC board. In the case of wire-bonding transition, a matching circuit was designed on the LTCC substrate and interconnection space between wires was optimized in terms of their angle. In addition, the wire-bonding structure of coplanar waveguide type was used to reduce radiation of EM-fields due to interconnection discontinuity. For high-isolated module structure, DC bias lines were fully embedded into the LTCC substrate and shielded with vias. Using 5-layer LTCC dielectrics, the power amplifier LTCC module was fabricated and its size is $4.6{\times}4.9{\times}0.5mm^3$. The fabricated module shows the gain of 10 dB and the output power of 11 dBm at P1dB compression point from 60 to 65 GHz.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.27 no.10
• /
• pp.941-944
• /
• 2016

This paper proposes 24 GHz power amplifier for automotive collision avoidance and surveillance short range radar using Samsung 65-nm CMOS process. The proposed circuit has a 2-stage differential power amplifier which includes common source structure and transformer for single to differential conversion, impedance matching, and power combining. The measurement results show 15.5 dB maximum voltage gain and 3.6 GHz 3 dB bandwidth. The measured maximum output power is 13.1 dBm, input $P1_{dB}$ is -4.72 dBm, output $P1_{dB}$ is 9.78 dBm, and maximum power efficiency is 17.7 %. The power amplifier consumes 74 mW DC power from 1.2 V supply voltage.

• Proceedings of the KIEE Conference
• /
• 1995.07c
• /
• pp.1365-1367
• /
• 1995

The PLS 2-GeV linac employs 11 units of high-power pulsed klystrons(80MW) as the main RF sources. The matching modulators of 200 MW(400kV, 500 A) can provide a flat-top pulse width of 4.4 ${\mu}s$ with a maximum pulse repetition rate of 120 Hz at the full power level. For a good stability of electron beams, the pulse-to-pulse flat-top voltage variation of a modulator requires less than 0.5%. In order to achieve this goal, we stabilized high voltage charging power supplies within 1% by a phase controlled SCR voltage regulator. In addition, we employed ac/dc feedback together with a resistive De-Q'ing system to achieve far less than 0.5% variation of the PFN charging voltage. This paper presents the main feature of the klystron-modulator system and the characteristics of the pulsed high-power RF system performance during the beam injection operation for the Pohang Light Source commissioning.

• Proceedings of the IEEK Conference
• /
• 2005.11a
• /
• pp.261-264
• /
• 2005

This paper presents the design of a down-conversion mixer with built-in active balun integrated in a $0.25\;{\mu}m$ pHEMT process. The active balun consists of series-connected common-gate FET and common-source FET. The designed balun achieved broadband characteristics by optimizing gate-width and bias condition for the reduction in parasitic effect. From DC to more than 6GHz, the active balun shows the phase error of less than 3 degree and the gain error of less than 0.4 dB. A single-balanced down-conversion mixer with built-in broadband active balun has been designed with optimum width, load resistor and bias for conversion gain and without any matching component for broadband operating. The designed mixer whose size of including on-chip bias circuit is $1\;mm{\times}1\;mm$ shows the conversion gain of better than 7 dB from 2 GHz to 6 GHz and $P_{1dB}$ of -10 dBm at 5.8 GHz

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.29 no.5
• /
• pp.393-396
• /
• 2018

Herein, a 94-GHz low-noise amplifier (LNA) using the 65-nm CMOS process is presented. The LNA is composed of a four-stage differential common-source amplifier and impedance matching is accomplished with transformers. The fabricated LNA chip shows a peak gain of 25 dB at 94 GHz and has a 3-dB bandwidth at 5.5 GHz. The chip consumes 46 mW of DC power from a 1.2-V supply, and the total chip area, including the pads, is $0.3mm^2$.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.20 no.1
• /
• pp.131-141
• /
• 2016

SRM is designed to meet operating standards such as low cost, simple magnetic structure, a desired operating speed range, high efficiency, high performance, and good matching for DC power. The magnetic flux of SRM is independent of its direction to develop a torque and it allows the flexible characteristics of the magnetic structure for SRM. In this paper, SRM can widely classify two types, Radial-Flux SRM and Axial-Flux SRM, according to the flux direction. Radial-Flux SRM includes Conventional, Segmented stator and rotor, and Double stator SRM, etc. and Axial-Flux SRM includes C-core stator and the Axial-airgap SRM. This paper is subjected the basic characteristics to select the best of the magnetic structure of SRM in the appropriate application by the classification of SRM.