• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.07a
• /
• pp.427-431
• /
• 2000

ITO (indium tin oxide) thin films on PET (polyethylene terephthalate) and glass substrates have been deposited by a dc magnetron sputtering without heat treatments such as substrate heater and post heat treatment. Each sputtering parameter during the sputtering deposition is an important factor for the high quality of ITO thin films deposited on polymeric substrate. Particularly, the material, electrical and optical properties of as-deposited ITO oxide films are dominated by sputtering power, oxygen partial pressure and films thickness. As the experimental results, the XRD patters of ITO films are influenced by sputtering power and pressure. As the power and pressure are increased, (411) peak is grown suddenly. the electrical resistivity is also increased, as the sputteing power and pressure are increased. Transmittance of ITO thin films in visible light ranges is lowered with increasing the sputtering power and film thickness. Reflectance of ITO films in infia-red region is decreased, as the power and pressure is increased.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.05c
• /
• pp.83-87
• /
• 2003

Thin films of amorphous carbon (a-C) generally combine high wear resistance with low friction coefficients and a-C films have widespread applications as protective coatings and passivation of electrical circuit and insulating layer. In this work we deposited the amorphous carbon (a-C) films on silicon substrate with a high rate DC magnetron sputtering system. It is obtained parameters on the deposition rate and physical properties of a-C films using a wide range of Ar gas pressure and DC power. The physical properties of the films were analyzed by Nanoindenter and AFM (Atomic Force Microscopy), The electrical properties were investigated by electrical conductivity measurement.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.21 no.7
• /
• pp.660-664
• /
• 2008

Titanium nitride (TiN) thin films are widely used for hard coatings due to their superior hardness, chemical stability, low friction and good adhesion properties. In this study, we investigated the effect of DC power on the characteristics of TiN thin films deposited on Si and glass substrates by DC magnetron sputtering using TiN target. We made TiN films of 300 nm thickness with various DC powers. The structural properties of films are investigated by x-ray diffractions (XRD) and tribological properties are measured by nano-indentation, nano-scratch tester. The rms roughness was measured by atomic forced microscopy (AFM). In the result, TiN films had the smooth surface and exhibited (111) directions with the increase of DC Power. Also, especially in case of 175 W DC power, TiN film exhibited the maximum hardness about 8 GPa, and the critical load near 25.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.06a
• /
• pp.269-269
• /
• 2007

최근 평판디스플레이 산업이 성장함에 따라 품질향상을 위한 연구가 활발히 진행중이며 또한, 부품 소재 개발에 박차를 가하고 있다. 대형 평판디스플레이 중 낮은 전력소모와 광시야각이 우수한 TFT-LCD가 각광받고 있다. TFT-LCD 소자의 투명전극으로 사용되기 위해서는 면저항 10~1k Ohm/sq., 광투과율 85% 이상의 특성이 요구되며 ITO(Indium Tin Oxide의 약자) 타겟을 스퍼터링한 박막이 일반적으로 사용되고 있다. 본 연구에서는 $In_2O_3$ 나노 분말 제조 공법으로 제작된 ITO 타겟을 사용하여 양산성 및 대형화에 적합한 DC 마그네트론 스퍼터 방식으로 투명전극을 제조하였다. 일반적으로 사용되는 고정식 DC 마그네트론 스퍼터 방식은 타겟표면에 재증착(back deposition)되는 저급산화물로 인해 이물 또는 노즐(Nodule) 이 형성되고 이로 인해 비이상적이고 불안정한 방전 플라즈마가 박막의 특성을 저하시킨다. 이러한 문제점을 해결하기 위해 이동식 DC 마그네트론 스퍼터 방식을 채택하였으며 대형 타겟을 이용한 대형화 기판 제작과 안정적인 sputter yield로 인해 uniformity가 우수한 ITO 박막을 제조하였다. ITO 박막의 저면저항 고투과율 특성을 구현하기 위해 공정변수인 산소분압, 전류밀도(DC power) 그리고 증착온도에 따른 ITO 박막의 미세조직과 결정성을 관찰하였으며 전기적 특성을 분석하였다.

• Journal of the Korean institute of surface engineering
• /
• v.47 no.6
• /
• pp.311-315
• /
• 2014

Indium tin oxide (ITO) thin films (30 nm) were deposited on PET substrate by reactive DC magnetron sputtering using In/Sn(2, 5 wt.%) metal alloy target without intentionally substrate heating during the deposition under different DC powers of 70 ~ 110 W. The electrical properties were estimated by Hall-effect measurements system. The resistivity of ITO thin film deposited using In/Sn (5 wt.%) metal alloy target at low DC power increased with increasing annealing time. However, they increased with increasing annealing time at high DC power. In the case of ITO (Sn 2 wt%), we can't find clear change in resistivity with increasing annealing time. However, carrier density and mobility showed difference behavior due to change of oxygen vacancy.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2003.03a
• /
• pp.67-67
• /
• 2003

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2000.11a
• /
• pp.62-62
• /
• 2000

• Korean Journal of Materials Research
• /
• v.9 no.7
• /
• pp.688-694
• /
• 1999

Ti-6Al-4V-N films have been grown onto glass substrates by dc reactive magnetron sputtering from a Ti-6Al-4V-N alloy target at different nitrogen partial pressure, input powers and sputtering times. The influence of various sputtering conditions on structural properties of Ti-6Al-4V-N films was investigated by measuring their X-ray diffraction. The quaternary Ti-6Al-4V-N film is crystallizing in a face centered cubic TiN structure, the lattice parameter is smaller than the TiN parameter as titanium atoms of the TiN lattice are replaced by aluminum and vanadium atoms. The films show the (111) preferred orientation and the (111) peak intensity decreases as the nitrogen partial pressure is increased, but the intensity increases as the sputtering time is increased. The deposition rate and the grain size are alto related with the variation of various sputtering conditions.

• Journal of the Korean institute of surface engineering
• /
• v.35 no.6
• /
• pp.415-421
• /
• 2002

Ti-Si-N coating layers were codeposited on silicon wafer substrates by a DC reactive magnetron sputtering technique using separate titanium and silicon targets in $N_2$/Ar gas mixtures. The oxidation behavior of Ti-Si-N coating layers containing 4.0 at.%, 10.0 at.%, and 27.3 at.% Si was investigated at temperatures ranging from 600 to $960^{\circ}C$. The coating layers containing 4.0 at.% Si became fast oxidized from $600^{\circ}C$ while the coating layers containing 10.0 at.% Si had oxidation resistance up to $800^{\circ}C$. It was concluded that an increase in Si content to a level of 10.0 at.% led to the formation of finer TiN grains and a uniformly distributed amorphous Si3N4 phase along grain boundaries, which acted as efficient diffusion barriers against oxidation. However, the coating layers containing 27.3 at.% Si showed relatively low oxidation resistance compared with those containing 10.0 at.% Si. This phenomenon would be explained by the existence of free Si which was not nitrified in the coating layers containing 27.3 at.% Si.

• Korean Journal of Materials Research
• /
• v.20 no.1
• /
• pp.47-50
• /
• 2010

Various thicknesses of Al-doped ZnO (AZO) films were deposited on glass substrate using pulsed dc magnetron sputtering with a cylindrical target designed for large-area high-speed deposition. The structural, electrical, and optical properties of the films of various thicknesses were characterized. All deposited AZO films have (0002) preferred orientation with the c-axis perpendicular to the substrate. Crystal quality and surface morphology of the films changed according to the film thickness. The samples with higher surface roughness exhibited lower Hall mobility. Analysis of the measured data of the optical band gap and the carrier concentration revealed that there were no changes for all the film thicknesses. The optical transmittances were more than 85% regardless of film thickness within the visible wavelength region. The lowest resistivity, $4.13\times10^{-4}\Omega{\cdot}cm^{-1}$ was found in 750 nm films with an electron mobility $(\mu)$ of $10.6 cm^2V^{-1} s^{-1}$ and a carrier concentration (n) of $1.42\times10^{21} cm^{-3}$.