• The Korean Journal of Ceramics
• /
• v.4 no.1
• /
• pp.20-24
• /
• 1998

Thin films of diamond-like carbon(DLC) can be successfully deposited by using a magnetron plasma chemical vapor deposition (CVD) method with an rf(13.56 MHz) plasma of $C_dH_8$. Plasma characteristics are analyzed as a function of the magnetic field. As the magnetic field increases, both electron temperature ($T_e$) and density ($n_e$)increase, but the negative dc self-bias voltage (-$V_{ab}$) decreases, irrespective of gas pressures in the range of 1~7 mTorr. High deposition rates have been obtained even at low gas pressures, which may be attributed to the increased mean free path of electrons in the magentron plasma. Effects of rf power and additive gas on the structural properties of DLC films aer also examined by using various technique namely, TED(transmissio electron diffraction) microanalysis, FTIR, and Raman spectroscopies.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.07b
• /
• pp.748-752
• /
• 2004

The Hydrogenated amorphous carbon (a-C:H) thin films are deposited to fabricate suppored layer on silicon substrate with a closed field unbalanced magnetron(CFUBM) sputtering system. This study focuses on the characteristic of Diamond like carbon (DLC) films and Pb(Zr,Ti)$O_3$ (PZT) films for membrane structure. The deposition rate and the surface roughness of DLC fims decrease with DC bias voltage. hardness is 26 GPa at -200 V. Interface of DLC/Si and Pt/DLC layers was excellent.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2010.06a
• /
• pp.385-385
• /
• 2010

In this work, we have investigated the etching characteristics of $TiO_2$ and selectivity of $TiO_2$ over $SiO_2$ thin films as resistance in ReRAM using the inductively coupled plasma. The etch rate and selectivity were measured by varying the $BCl_3$ addition into Ar plasma. The maximum etchrate was obtained at 110.1nm/min at $BCl_3$/Ar=5sccm/10sccm, 500W for RFpower, -100v for DC-bias voltage, and 2Pa for the process pressure. The etched $TiO_2$ surface was investigated with X-ray photo electron spectroscopy. We explained the etching mechanism in two etch mechanisms, physiclas puttering and chemical reaction.

• 한국초전도학회:학술대회논문집
• /
• v.10
• /
• pp.207-210
• /
• 2000

Properties of SrTiO$_3$ thin films were characterized under the influence of an applied dc voltage utilizing a gold resonator with a flip-chip capacitor. The measurements were performed at microwave frequency ranges and low temperatures cryogenic temperatures. The dielectric constant of 830 and the low loss tangent of 6X10$^{-3}$ at 3.64 GHz were observed at 90 K and 100 V. The quality in the SrTiO$_3$ film was presented in terms of fractional frequency under the bias voltages and cryogenic temperatures.

• Proceedings of the KSME Conference
• /
• 2008.11a
• /
• pp.1947-1950
• /
• 2008

Printing technology is a very useful method in the several process of industrial fabrication due to noncontact and fast pattern generation. To make micro pattern, we investigate the electrostatic induced inkjet printer head for micro droplet generation and drop-on-demand jetting. In order to achieve the drop-on-demand micro droplet ejection by the electrostatic induced inkjet printer head, the pulsed DC voltage is supplied. In order to find optimal pulse conditions, we tested jetting performance for various bias and pulse voltages for drop-on-demand ejection. In this result, we have successful drop-on-demand operation and micro patterning. Therefore, our novel electrostatic induced inkjet head printing system will be applied industrial area comparing conventional printing technology.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.11a
• /
• pp.124-125
• /
• 2005

ZnS:Mn thin films have attracted great interest as electroluminescence devices. In this study, inductively coupled BCl$_3$/Ar plasma was used to etch ZnS:Mn thin films. We obtained the maximum etch rate of ZnS:Mn thin films was 2209 ${\AA}$/min at a BCl$_3$(20%)/Ar(80%) gas mixing ratio, an RF power of 700 W, a DC bias voltage of-250 V, a total gas flow of 20 sccm, and a chamber pressure of 1 Pa. It was proposed that sputter etching is dominant etching mechanism while the contribution of chemical reaction is relatively low due to low volatility of etching products.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.17 no.10
• /
• pp.1061-1067
• /
• 2004

In this study, ferroelectric (Ba,Sr)TiO$_3$ and high temperature superconductor YBCO thin films were fabricated by PLD (Pulsed Laser Deposition) method and tuneable bandstop filters were implemented with two different IDC(Interdigital Capacitance) gap patterns, 20${\mu}{\textrm}{m}$ and 30${\mu}{\textrm}{m}$ using these two thin film layers. The resonant frequency was changed by DC bias voltage. By comparing measured results with simulation, the dielectric properties of ferroelectric thin film have been extracted. The permittivity was 820 ～ 900 at 30 K and had an acceptable error range but the loss tangent had a great difference, 0.018 in 30${\mu}{\textrm}{m}$ IDC gap pattern and 0.037 in 20 ${\mu}{\textrm}{m}$.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.07a
• /
• pp.404-407
• /
• 2003

Among the ferroeletric thin films that have been widely investigated for ferroelectric random access memory (FRAM) applications, the $SrBi_2Ta_2O_9$ (SBT) thin film is appropriate as a memory capacitor material due to its excellent fatigue endurance. SBT thin films were etched in high-density $Cl_2/Ar$ in inductively coupled plasma. The maximum etch rate of SBT film is $1834\;{\AA}/min$ under $Cl_2/(Cl_2+Ar)$ of 30 %, rf power of 700 W, dc-bias voltage of -250 V, chamber pressure of 11 mTorr and gas flow rate of 20 sccm.

• Proceedings of the Korean Radioactive Waste Society Conference
• /
• 2005.11b
• /
• pp.300-315
• /
• 2005

Recently plasma surface-cleaning or surface-etching techniques have been focused in the respect of decontamination of spent or used nuclear parts and equipment. In this study decontamination rate of metallic cobalt surface was experimentally investigated via its surface etching rate with a $CF_4-O_2$ mixed gas plasma and metallic surface wastes of cobalt oxides were simulated and decontaminated with $NF_3$ - Ar mixed gas plasma. Experimental results revealed that a mixed etchant gas with about $80{\%}\;CF_4-20{\%}\;O_2$ gives the highest reaction rate of cobalt disk and the rate reaches with a negative 300 DC bias voltage up to $0.43\;{\mu}m$/min at $380^{\circ}C$ and $20{\%}\;NF_3-80\%$ Ar mixed gas gives $0.2\;{\mu}m$/min of reaction rate of cobalt oxide film.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.16 no.4
• /
• pp.286-291
• /
• 2003

(Pb,Sr)TiO$_3$(PST) thin films have attracted great interest as new dielectric materials of capacitors for Gbit dynamic random access memories. In this study, inductively coupled CF$_4$/Ar plasma was used to etch PST thin films. The maximum etch rate of PST thin films was 740 $\AA$/min at a CF$_4$(20 %)/Ar(80 %) 9as mixing ratio, an RF power of 800 W, a DC bias voltage of -200 V, a total gas flow of 20 sccm, and a chamber pressure of 15 mTorr. To clarify the etching mechanism, the residue on the surface of the etched PST thin films was investigated by X-ray photoelectron spectroscopy. It was found that Pb was mainly removed by physically assisted chemical etching. Sputter etching was effective in the etching of Sr than the chemical reaction of F with Sr, while Ti can almost removed by chemical reaction.