• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.06a
• /
• pp.138-138
• /
• 2008

In this study, effect of thickness on structural, electrical and optical properties of B doped ZnO:Al (AZOB) films was investigated. AZOB films were deposited on PC substrates by DC magnetron sputtering. The thickness range of films were from 300 nm to 800 nm to identified as increasing thickness, stress between substrate and AZOB film. The. average transmittance of the films was over 80 % until 500 nm. Then a resistivity of $1.58\times10^{-3}\Omega$-cm was obtained. We presented that a AZOB film of 500 nm was optimization to obtain a high transmittance and conductivity.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.8 no.3
• /
• pp.62-67
• /
• 2009

Pt thin films on Cr or Ti interlayer were deposited onto a tungsten carbide(WC) substrate by the ion beam assisted DC magnetron sputtering. The various atomic percent of Cr and Ti underneath of the Pt films were prepared to examine the total thin film characteristics. The microstructure and surface analysis of the specimen were conducted by using the SEM, XRD and AFM. Mechanical properties such as hardness and adhesion strength of Pt thin film also were examined. The interlayer of pure Ti was formed with 40 nm thickness while that of pure Cr was done with 50 nm as standard reference. The growth rate of either Cr or Ti thin film was almost same under the same deposition conditions. The SEM images showed that anisotropic grain of Pt thin films consisting of dense columnar structures irrespectively grew from the different target compositions. The values of hardness and adhesion strength of Cr/Pt thin film coated on a WC substrate were higher than those of Ti/Pt thin film.

• Journal of the Korean Magnetics Society
• /
• v.5 no.3
• /
• pp.210-215
• /
• 1995

$Glass\Cr_{40\AA}\{[Cr_{10\AA}\NiFe_{50\AA}]}_N$ multilayers (number of layer N = 1, 2, 3, 4, 5, 6, 10) were made by dc magnetron sputtering under magnetic anisotropy of 200 G. Magnetoresistance curve MR(xx), MR(xy) were measured for the parallel and perpendicular current direction to external magnetic field. MR(xx) curves for the number of layer N=1, 5, 10 were almost became about zero percent, however the curves of other numbers appeared the phenomena of "positive magnetoresistance" that the resistance increased to external magnetic field, and the irregular and reversed curves in the vicinity of H=0 Oe.

• Journal of Environmental Science International
• /
• v.16 no.6
• /
• pp.683-688
• /
• 2007

In this study, N doped $TiO_2$ (TiO-N) thin film was prepared by DC magnetron sputtering method to show the photocatalytic activity in a visible range. Various gases (Ar, $O_2\;and\;N_2$) were used and Ti target was impressed by 1.2 kW -5.8 kW power range. The hysteresis of TiO-N thin film as a function of discharge voltage wasn't observed in 1.2 and 2.9kW of applied power. Cross sections and surfaces of thin films by FE-SEM were tiny and dense particle sizes of both films with normal cylindrical structures. XRD pattern of $TiO_2$ and TiO-N thin films was appeared by only anatase peak. Red shift in UV-Vis adsorption spectra was investigated TiO-N thin film. Photoactivity was evaluated by removal rate measurement of suncion yellow among reactive dyes. The photodegradation rate of $TiO_2$ thin film on visible radiation was shown little efficiency but TiO-N was about 18%.

• Proceedings of the KIEE Conference
• /
• 2006.07c
• /
• pp.1396-1397
• /
• 2006

Process variables for manufacturing the $CuInSe_2$ thin film were established in order to clarify optimum conditions for growth of the thin film depending upon process conditions (substrate temperature, sputtering pressure, DC/RF Power), and then by changing a number of vapor deposition conditions and Annealing conditions variously, structural and electrical characteristics were measured. Thereby, optimum process variables were derived. For the manufacture of the $CuInSe_2$, Cu, In and Se were vapor-deposited in the named order. Among them, Cu and In were vapor-deposited by using the sputtering method in consideration of their adhesive force to the substrate, and the DC/RF power was controlled so that the composition of Cu and In might be 1 : 1, while the surface temperature haying an effect on the quality of the thin film was changed from $100[^{\circ}C]$ to $300[^{\circ}C]$ at intervals of $50[^{\circ}C]$.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.20 no.6
• /
• pp.520-526
• /
• 2007

In order to acquire fundamental informations to fabricate high precision thin film resistors, NiCr/NiCrSi alloy films were prepared using Ni and Cr targets. Effect of composition on the electrical properties of the NiCr/NiCrSi alloy film were then investigated. Considering the effect of Si doping on the electrical and material characteristics, the lower TCR (temperature coefficient of resistance) values could be achieved for samples with Ni/Cr ratio of $0.8{\sim}1.5$ (in a range of relative higher specific resistivity and Cr composition of $40\;wt%{\sim}55\;wt%$) and with Si doping. Consequently, the sample prepared using a DC power showed a good TCR of $-25\;ppm/^{\circ}C$, which implies that increase of specific resistivity and decrease of TCR would be achieved more efficiently not for Ni-Cr binary material but for Si doped Ni-Cr ternary material, and not using RF power but using DC power in the sputtering process.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.21 no.11
• /
• pp.977-980
• /
• 2008

We investigated the effects of power ratio on the electrical and optical properties of Au based Ga-, B- codoped ZnO(GZOB) thin films. GZOB thin films were deposited on Au based poly carbonate(PC) substrate with various power in the range from 60 to 120 W by DC magnetron sputtering. In the result, GZOB films at 100 W exhibited a low resistivity value of $1.12\times10^{-3}\Omega-cm$, and a visible transmission of 80 % with a thickness of 300 nm. This result indicated that the addition of Ga and B in ZnO films leads to the improvement of conductivity and transparent. From the result, we can confirm the possibility of the application as transparent conductive electrodes.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.11a
• /
• pp.144-144
• /
• 2007

Effects of power ratio on the electrical and optical properties of Au based Ga-, B- codoped ZnO(GZOB) thin films were investigated. GZOB thin films on Au based PC flexible substrate were deposited at various power in the range from 50 to 125 W by DC magnetron sputtering. Au layer was fabricated to achieve good electrical conductivity. The presence of additional boron impurity leads to improve structural defects. Thus, the c-axis orientation along (002) plane was enhanced with the increasing of power ratio and the surface morphology of the films showed a homogeneous and nano-sized microstructure. GZOB films grown at 125W were investigated a low resistivity value of $1{\times}10^{-3}{\Omega}cm$ and a visible transmission of 80% with a thickness of 300nm.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.06a
• /
• pp.354-355
• /
• 2007

Process variables for manufacturing the $CuInSe_2$ thin film were established in order to clarify optimum conditions for growth of the thin film depending upon process conditions (substrate temperature, sputtering pressure, DC/RF Power), and then by changing a number of vapor deposition conditions and Annealing conditions variously, structural and electrical characteristics were measured. Thereby, optimum process variables were derived. For the manufacture of the $CuInSe_2$, Cu, In and Se were vapor-deposited in the named order. Among them, Cu and In were vapor-deposited by using the sputtering method in consideration of their adhesive force to the substrate, and the DC/RF power was controlled so that the composition of Cu and In might be 1 : 1, while the surface temperature having an effect on the quality of the thin film was changed from 100[$^{\circ}C$] to 300[$^{\circ}C$] at intervals of 50[$^{\circ}C$].

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.02a
• /
• pp.188-188
• /
• 2010

최근까지는 주로 비정질 실리콘이 디스플레이의 채널층으로 상용화 되어왔다. 비정질 실리콘 기반의 박막 트랜지스터는 제작의 경제성 및 균일성을 가지고 있어서 널리 상용화되고 있다. 하지만 비정질 실리콘의 구조적인 문제인 낮은 전자 이동도(< 1 cm2/Vs)로 인하여 디스플레이의 대면적화에 부적합하며, 광학적으로 불투명한 특성을 갖기 때문에 차세대 디스플레이의 응용에 불리한 점이 있다. 이런 문제점의 대안으로 현재 국내외 여러 연구 그룹에서 산화물 기반의 반도체를 박막 트랜지스터의 채널층으로 사용하려는 연구가 진행중이다. 산화물 기반의 반도체는 밴드갭이 넓어서 광학적으로 투명하고, 상온에서 증착이 가능하며, 비정질 실리콘에 비해 월등히 우수한 이동도를 가짐으로 디스플레이의 대면적화에 유리하다. 특히 Zinc Oxide, Tin Oxide등의 산화물이 연구되고 있으며, indium이나 aluminum등을 첨가하여 전기적인 특성을 향상시키려는 노력을 보이고 있다. 본 연구에서는 Zinc Oxide 기반의 박막 트랜지스터를 DC magnetron sputtering를 이용하여 상온에서 제작한 후 다양한 조건에서의 후열처리를 통하여 소자의 특성의 최적화를 이루는 것을 시도하였다. 그리고 ITO를 전극으로 사용하여 bottom gate 구조의 박막 트랜지스터를 만들고 air 분위기에서 온도별, 시간별 열처리를 진행하였다. 또한 gate insulator의 처리를 통하여 thin film의 interface 개선을 통하여 소자의 성능 향상을 시도 하였다. semiconductor analyzer로 소자의 출력 특성 및 전이 특성을 평가하였다. 그 결과 기존의 a-Si 기반의 박막 트랜지스터보다 우수한 이동도의 특성을 갖는 ZnO 박막 트랜지스터를 얻었다. 그리고 이를 바탕으로 ZnO를 이용하여 대면적 적합한 디스플레이를 제작할 수 있다는 가능성을 보인다. 그리고 Temperature, Bias Temperature stability, 경시변화 등의 다양한 조건에서의 안정성을 평가하여 안정성이 향상을 확보하여 비정질 실리콘을 대체할 유력한 후보중위 하나가 될 것이라고 생각된다.