• Journal of Electrical Engineering and Technology
• /
• 제1권1호
• /
• pp.63-72
• /
• 2006

The purpose of this raper is to address the negative impedance instability in DC/DC converters. We present the negative impedance instability of PWM DC/DC converters loaded by constant power loads (CPLs). An approach to design digital controllers for DC/DC converters Is presented. The proposed method, called Power Alignment control technique, is applied to DC/DC step-down choppers operating in continuous conduction or discontinuous conduction modes with CPLs. This approach uses two predefined state variables instead of conventional pulse width modulation (PWM) to regulate the output voltage. A comparator compares actual output voltage with the reference and then switches between the appropriate states. It needs few logic gates and comparators to be implemented thus, making it extremely simple and easy to develop using a low-cost application specific integrated circuit (ASIC) for converters with CPLs. Furthermore, stability of the proposed controllers using the small signal analysis as well as the second theorem of Lyapunov is verified. Finally, simulation and analytical results are presented to describe and verify the proposed technique.

• Journal of Power Electronics
• /
• 제16권6호
• /
• pp.2315-2326
• /
• 2016

This paper discusses the elimination of DC voltage deviation and the enhancement of load current sharing accuracy in multi-terminal high voltage direct current (MT-HVDC) systems. In order to minimize the power line losses in different parallel network topologies and to insure the stable operation of systems, a decentralized control method based on a modified droop control is presented in this paper. Averaging the DC output voltage and averaging the output current of two neighboring converters are employed to reduce the congestion of the communication network in a control system, and the decentralized control method is implemented. By minimizing the power loss of the cable, the optimal load current sharing proportion is derived in order to achieve rational current sharing among different converters. The validity of the proposed method using a low bandwidth communication (LBC) network for different topologies is verified. The influence of the parameters of the power cable on the control system stability is analyzed in detail. Finally, transient response simulations and experiments are performed to demonstrate the feasibility of the proposed control strategy for a MT-HVDC system.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 1999년도 전력전자학술대회 논문집
• /
• pp.93-96
• /
• 1999

Solar cell generate DC power from sunlight whose power is different at any instance according to condition of variables : insolation and temperature. In order to improve the system utility factor and efficiency of energy conversion, it is desirable to operate the PV system at maximum power point of solar cell under different condition. In this paper, Boost chopper is controlled it output voltage with a new discrete control algorithm for MPPT. PWM signal of DC-DC converter are generated with a 89C51 microcontroller. Switching frequency of DC-DC converter is set at 10KHz. Simulation and experimental results show that the PV system studied in this paper is always operated at maximum power point under different maximum power point of solar cells having stabilized output voltage waveform with relatively small ripple component

• 전기의세계
• /
• 제22권4호
• /
• pp.11-16
• /
• 1973

This paper presents an optimum control of the field resistance for the self-excited DC shunt generator to keep a constant terminal voltage in case of the load change or the torque variation in the system. The non-linearity of the system is linearized by applying the small signal technique and the linearized equation is solved by the maximum principle with the digital computer. The optimal control value of the field resistance for the step error of the generator output voltage is obtained and the transient voltage characteristics in the system are investigated.

• Journal of Electrical Engineering and Technology
• /
• 제8권4호
• /
• pp.752-759
• /
• 2013

This paper proposes a method for fault diagnosis and fault-tolerant control of DC-link voltage sensor for two-stage three-phase grid-connected PV inverters. Generally, the front-end DC-DC boost converter tracks the maximum power point (MPP) of PV array and the rear-end DC-AC inverter is used to generate a sinusoidal output current and keep the DC-link voltage constant. In this system, a sensor is essential for power conversion. A sensor fault is detected when there is an error between the sensed and estimated values, which are obtained from a DC-link voltage sensorless algorithm. Fault-tolerant control is achieved by using the estimated values. A deadbeat current controller is used to meet the dynamic characteristic of the proposed algorithm. The proposed algorithm is validated by simulation and experiment results.

• 전기전자학회논문지
• /
• 제18권4호
• /
• pp.586-592
• /
• 2014

본 논문에서는 DT-CMOS(Dynamic Threshold voltage Complementary MOSFET) 스위칭 소자를 사용한 DC-DC Buck 컨버터를 제안하였다. 높은 효율을 얻기 위하여 PWM 제어방식을 사용하였으며, 낮은 온 저항을 갖는 DT-CMOS 스위치 소자를 설계하여 도통 손실을 감소시켰다. 제안한 Buck 컨버터는 밴드갭 기준 전압 회로, 삼각파 발생기, 오차 증폭기, 비교기, 보상 회로, PWM 제어 블록으로 구성되어 있다. 삼각파 발생기는 전원전압(3.3V)부터 접지까지 출력 진폭의 범위를 갖는 1.2MHz의 주파수를 생성하며, 비교기는 2단 증폭기로 설계되었다. 그리고 오차 증폭기는 70dB의 이득과 $64^{\circ}$의 위상여유를 갖도록 설계하였다. 또한 제안한 Buck 컨버터는 current-mode PWM 제어회로와 낮은 온 저항을 갖는 스위치를 사용하여 100mA의 출력 전류에서 최대 95%의 효율을 구현하였으며, 1mA 이하의 대기모드에도 높은 효율을 구현하기 위하여 LDO 레귤레이터를 설계하였으며, 또한 2개의 IC 보호 회로를 내장하여 신뢰성을 확보하였다.

• 전자공학회논문지
• /
• 제53권1호
• /
• pp.139-144
• /
• 2016

본 논문은 가변 스위칭 주파수 PFM을 이용한 DC-DC 변환기의 집적회로 개발 시, 적용 가능한 주요 기능 블록의 설계에 관한 것이다. DC전압 변환 시 부하에 공급되는 전류가 작거나 출력전압이 설정값 근처에 도달했을 때 PFM 모드로 동작시켜 전력변환 효율을 높일 수 있다. PFM DC-DC 변환기 구현에 필요한 PFM 신호 발생회로, PFM 주파수 제어기, 출력전압감지회로 그리고 과전류보호회로를 설계하였다. 설계를 위한 공정파라미터는 내압 12[V], 최소선폭 $0.35[{\mu}m]$, 2P_2M CMOS 공정을 사용하였다.

• Journal of Power Electronics
• /
• 제17권5호
• /
• pp.1137-1149
• /
• 2017

In order to reduce the cost, improve the efficiency and simplify the complicated control of existing isolated LED drivers, an improved boundary conduction mode (BCM) Buck ac-dc light emitting diode (LED) driver with extended output voltage and low total harmonic distortion is proposed. With a coupled inductor winding and a stacked output, its output voltage can be elevated to a much higher value when compared to that of the conventional Buck ac-dc converter, without sacrificing the input harmonics and power factor. Therefore, the proposed Buck LED driver can meet the IEC61000-3-2 (Class C) limitation and has a low THD. The operating principle of the topology and the design methodology of the ac-dc LED driver are presented. A 150 W ac-dc prototype was built in the laboratory and it shows that the input current harmonics meet the lighting standard. In addition, the THD is less than 16% at a typical ac input. The peak efficiency is higher than 96.5% at a full load and a normal input.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2001년도 춘계학술대회 논문집 전기기기 및 에너지변환시스템부문
• /
• pp.301-303
• /
• 2001

This paper proposes the boost input type active clamp DC-DC converter featuring the high efficiency and improved EMI characteristics. The main characteristic of the converter is to operate with the non-pulsating input and output currents. Besides, it has the zero-voltage switching (ZVS) and low voltage stress characteristics. For the proposed converter, the detailed operation principles and the simulation results are presented.

• 전기전자학회논문지
• /
• 제25권1호
• /
• pp.101-108
• /
• 2021

본 논문에서는 전기차 충전기용 모듈형 DC/DC 컨버터의 병렬 제어 기법을 제안한다. 전기차 충전기는 모듈형 컨버터를 적용하여 출력 전력 용량이 증가되고 있지만, 모듈간 구성 요소의 차이, 게이트 드라이버의 지연, 센싱 오차 등에 의해 출력 전류 불균형이 발생하며, 이는 전체 시스템의 효율 및 신뢰성 저하를 야기한다. 출력 전류 균등 분배를 위한 기존의 기법들은 전압 강하 또는 시스템 부피 및 비용이 증가한다는 단점을 갖는다. 본 논문에서는 전류 보상 성분을 고려한 병렬 제어 기법을 적용하여 시스템의 하드웨어 변동없이 출력 전류 균등 분배를 달성한다. 시뮬레이션을 통하여 제안하는 병렬 제어 기법의 성능 및 타당성을 검증한다.