• Proceedings of the KIEE Conference
• /
• 1993.07b
• /
• pp.870-872
• /
• 1993

With the using the microprocessor, this paper presents DC servo motor control characteristics by Self-Tuning PID controller and considers position control response with controller of DC servo motor for robot drive. As this system is supported by a channel, it is considered to enough application effect in industry region such as needing multi joint robot and precision parallel driving.

• Proceedings of the KIEE Conference
• /
• 1993.07b
• /
• pp.1020-1022
• /
• 1993

The speed control associated with do send motors for direct-drive applications of mobile robot is considered. In odor to the high-performance operation of dc servo motor, drive circuits is controlled Pulse Width Modulations. In this case, PWM driving circuit has nonliner charactristics. This circuit composed of H-type bridge with freewheeling diodes in odor to deal with storage energy of motor's inductance and also control method is developed. At resultes, speed charactristics of motor is shown lineristics. In oder to speed control of motor. The opertion of phase-locked servo system is described and a linear discrete model is developed to their behavior. Thise model discussed are the design problems, speed variation.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.11 no.4
• /
• pp.307-312
• /
• 2006

This paper proposes the SRM drive system, which accurately estimates the phase currents from the DC-link current to drive SRM instead of detecting the three-phase currents. In addition, the detecting circuit of DC-link current is also proposed to increase the resolution and decrease the off-set influence. Comparing with the general drive system based on the phase current, it is verified through the experiments that the proposed SRM drive system based on the DC-link current has the good performance in steady-state response of the speed control. Using the DC-link current, all of the 3-phase currents can be easily estimated for driving the SRM.

• Journal of Power Electronics
• /
• v.6 no.2
• /
• pp.146-162
• /
• 2006

This paper deals with the analysis, design and implementation of an AC-DC Zeta converter in discontinuous current mode (DCM) of operation used for power quality improvement at AC mains in direct torque controlled (DTC) permanent magnet synchronous motor (PMSM) drives. The designed Zeta converter feeds a direct torque controlled PMSM drive system. Modeling and simulation is carried out in a standard PSIM software environment. Test results are obtained on the developed prototype Zeta converter using DSP ADMC401. The results obtained demonstrate the effectiveness of the Zeta converter in improving power quality at AC mains in the PMSM drive system.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.13 no.2
• /
• pp.88-95
• /
• 2008

This paper proposes a fast fault detection algorithm under open-circuit fault of a switch for a brushless DC(BLDC) motor drive system. This proposed method is configured without the additional devices for fault detection and identification. The fault detection and identification are achieved by a simple algorithm using the operating characteristic of the BLDC motor. After the fault identification, the drive system is reconfigured for continuous operation. This system is reconfigured by four-switch topology connecting a faulty leg to the middle point of DC-link bidirectional switches. This proposed method can also be embedded into existing BLDC motor drive systems as a subroutine without excessive computational effort. The feasibility of a the proposed fault detection algorithm is validated in simulation and experiment.

• Proceedings of the KIPE Conference
• /
• 2003.07b
• /
• pp.844-847
• /
• 2003

The environmental problem and the drain of petroleum fuel resources has been became the center of public interest. So the electric drive attracts public attention. The vehicles for indoor works should not pollute air. Therefore it is also useful that applying electric drive to such an appliance. An 1.2[kw] SRM for a pallet truck drive is developed and tested. The drive system has to operate with low voltage and high current. The small size, robustness, high efficiency make it possible to replace with DC motor. Test results show that pallet truck with SRM has better characteristics than that of the DC motor performance.

• Proceedings of the KIEE Conference
• /
• 1991.07a
• /
• pp.559-563
• /
• 1991

Permanent magnet synchronous motor (PMSM) is receiving increased attention for servo drive applications in recent years because of its high torque to inertia ratio, superior power density and high efficiency. Vector-controlled PMSM has the same operating characteristics as separately excited dc motor. The drive system of servo motor is requested to have an accurate response for the speed reference and a quick recovery for the disturbance such as load torque. However the dynamics of PMSM drive change greately by parameter variations. Morever, when the unkown and inaccessible disturbances are imposed on PMSM, the drive system is given a significant effect by them. As a result, the drive system with both a fast drive performance and a reduced sensitivity to parameter variations is requested. In this paper, the robust control system of PMSM with torque feedforward using load torque observer is presented. In the proposed system, load torque is estimated by the reduced order observer, and the robust control system against load torque variation is realized using the torque feedforward. Moreover, the design of speed controller with the torque observer is discussed. Simulation results show that the proposed method is effective for suppression of parameter variations and load disturbance.

• Journal of Power Electronics
• /
• v.16 no.1
• /
• pp.142-152
• /
• 2016

Common mode voltage (CMV) generation is a major problem in switching power converter fed induction motor drive systems. CMV is the zero sequence voltage generated due to the switching action of power converters. Even a small magnitude of CMV with a high rate of change may circulate large bearing currents which may damage a machine's bearings and shorten its life. There are several methods of controlling CMV. This paper presents 3-level sinusoidal pulse width modulation based techniques to control the magnitude and rate of change of CMV in multilevel AC-DC-AC drive systems. Simulation and experimental investigations have been presented to validate the performance of proposed technique to control CMV in 3-level neutral point clamped inverter based AC-DC-AC system.

• Journal of Advanced Marine Engineering and Technology
• /
• v.31 no.8
• /
• pp.975-982
• /
• 2007

The single-phase switched reluctance motor(SRM) drive requires DC source which is generally supplied through a rectifier connected with a commercial source. The rectifier is consist of a diode full bridge and a filter circuit. Usually the filter circuit uses capacitor with large value capacitance to reduce ripple component of DC power. Although the peak torque ripple of SRM is small, the short charge and discharge current of the filter capacitor draws the low power factor and system efficiency. A modified single phase SRM drive system is presented in this paper, which includes drive circuit realizing reduction of torque ripple and improvement of power factor. In the proposed drive circuit, one switching part and diode which can separate the output of AC/DC rectifier from the filter capacitor is added. Also, a upper switch of drive circuit is exchanged a diode in order to reduce power switching device. Therefore the number of power switch device is not changed, two diodes are only added in the SRM drive. To verify the proposed system, some simulation and experimental results are presented.

• Proceedings of the KIEE Conference
• /
• 1996.07a
• /
• pp.406-408
• /
• 1996

This paper describes the BLDC motor which is applicated for a top front loading domestic washing machine. This motor is adopted direct drive washing machine without gear-belt-pulley system. Because gear box is removed, machine volume and noise are reduced. Moreover mechanical troubles in gear box are removed. Realization of variable speed region through of PWM control and high speed is able to efficient washing and spinning.