• Journal of Drive and Control
• /
• v.15 no.2
• /
• pp.22-31
• /
• 2018

This study deals with verifying the design feasibility, of an independently driving hydraulic system for disaster response purposes, through an analytical approach. The development target is a system in which four traveling motors are driven independently, and must be easy to operate even under conditions in which different loads are applied to the traveling motors. In order to be suitable for complex work, the hydraulic system was designed using the main control valve with a pressure compensation function. If we can develop an analytical model that reflects the specifications and functions of the parts through the analysis program, we can verify the validity of the design before we make the prototype. The purpose of this study therefore, is to verify the feasibility of designing an independent drive hydraulic system through the development of an analysis model from the viewpoint of complex work. The analysis program uses Simulation X.

• Journal of the Korean housing association
• /
• v.18 no.2
• /
• pp.105-112
• /
• 2007

This research has been implemented based on the area of #369 Dowon-dong, Dalseo-gu, Dae-gu which is considered as a place with satisfactory characteristics for the flow of fresh air into the city. Simulations of the target area both prior to the development plan and after apartment complex blocking were analyzed in regard to blocking planning and pilotis based on the main direction of wind, $90^{\circ}$ (east wind) and $180^{\circ}$ (south wind). In addition, congested wind corridor flow in the target place was identified through a pollution spread simulation according to the wind corridor. Therefore, the flow of wind in the one area is affected by the blocking of the complex and the main direction of the wind. Also blocking, in regard of pilotis, provides a better flow of wind. This study was implemented based on wind formation by apartment complex planning, so further study on the other factors affecting the flow of a wind corridor along with block planning and pilotis need to be carried out. Sustainable environmental factors through analysis of the environmental factors have to be analyzed. Moreover, building and complementing fundamental resources and systematic devices should be supported.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2005.11a
• /
• pp.573-576
• /
• 2005

This research presents a three-dimensional modeling technique for a flexible sheet. A relative coordinate formulation is used to represent the kinematics of the sheet. The three-dimensional flexible sheet is modeled by multi-rigid bodies interconnected by out-of-plane joints and plate force elements. A parent node is designated as a master body and is connected to the ground by a floating joint to cover the rigid motion of the flexible sheet in space. Since the in-plane deformation of a sheet such as a paper and a film is relatively small, compared to out-of-plane deformation, only the out-of-plane deformation is accounted for in this research. The recursive formulation has been adopted to solve the equations of motion efficiently. An example is presented to show the validity of the proposed method.

• Journal of the Korean Society of Mineral and Energy Resources Engineers
• /
• v.55 no.6
• /
• pp.649-659
• /
• 2018

In this study, after operational data for a landfill gas power plant were collected, the methane gas concentration was predicted using a deep learning method. Concentrations of methane gas, carbon dioxide, hydrogen sulfide, oxygen concentration, as well as data related to the valve opening degree, air temperature and humidity were collected from 23 pipeline bases for 88 matches from January to November 2017. After the deep learning model learned the collected data, methane gas concentration was estimated by applying other data. Our study yielded extremely accurate estimation results for all of the 23 pipeline bases.

• Korean Chemical Engineering Research
• /
• v.47 no.5
• /
• pp.587-592
• /
• 2009

Heat transfer model and energy dissipation rate were investigated to examine the heat transfer mechanism in bubble columns with continuous operation. The energy dissipation rate($E_D$) obtained from the unsteady state heat transfer model based on the surface renewal theory was significantly small, comparing with the hydrodynamic energy dissipation rate($P_v$) calculated from the overall hydrodynamic energy balance based on the behaviors and holdups of gas and liquid phases in the column. It was found from these results that the energy dissipation rate based on the surface renewal theory is independent of the hydrodynamic energy dissipation rate obtained from the overall hydrodynamic energy balance in the bubble column, in considering their mechanism. The different two energy dissipation rates were correlated in terms of operating variables within this experimental conditions, respectively.

• Journal of Korean Society of Steel Construction
• /
• v.15 no.2
• /
• pp.125-135
• /
• 2003

A 3-dimensional model of curved steel box girder bridges without diaphragm was presented. This model yielded results that were consistent with those of the parameter analysis using the BEF and Ritz methods. Se veralmodels with diaphragms were analyzed to estimate the appropriate diaphragm spacing. In case of 50m span, models A-10, A-20, A-30, B-10, B-20, and B-30 were found to have 5(8.3m), 7(6.25m), 8(5.5m), 4(10m), 6(7.1m), and 7(6.25m) diaphragms, respectively. In addition, a formula that presents the ratio of distortional stress to bending stresswas created from the results of the 3-dimensional FEM model analysis.

• Korean Journal of Optics and Photonics
• /
• v.24 no.1
• /
• pp.29-38
• /
• 2013

In this paper, the illumination performances of three freeform lenses optimally designed for a point source were investigated for several LEDs with different source sizes, and also the tolerance characteristics of the lenses were analyzed. For comparison, two lenses with different sizes were designed with a divergent illumination model, and the last one was done with an overlapped illumination model. As the LED source size increased, the illuminance uniformity decreased more strongly, and the influence of a source misalignment on illumination performance became insignificant. However, the variation of LED radiation characteristics had strong effect on the illumination performance, irrespective of LED source size. Even though the lens based on a divergent illumination model showed superior performance compared to the lens based on an overlapped illumination model, the latter was less sensitive to the variation of LED radiation characteristics.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.35 no.1
• /
• pp.1-11
• /
• 2015

In this study, an online seed potato sorting system using a visible and near infrared (40 1100 nm) transmittance spectral technique and statistical model was evaluated for the nondestructive determination of infected and sound seed potatoes. Seed potatoes that had been artificially infected with Pectobacterium atrosepticum, which is known to cause a soil borne disease infection, were prepared for the experiments. After acquiring transmittance spectra from sound and infected seed potatoes, a determination algorithm for detecting infected seed potatoes was developed using the partial least square discriminant analysis method. The coefficient of determination($R^2_p$) of the prediction model was 0.943, and the classification accuracy was above 99% (n = 80) for discriminating diseased seed potatoes from sound ones. This online sorting system has good potential for developing a technique to detect agricultural products that are infected and contaminated by pathogens.

• Science of Emotion and Sensibility
• /
• v.14 no.2
• /
• pp.191-196
• /
• 2011

Fabric extraction force measured through nozzle tester reflects a comprehensive fabric handle. Nozzle tester takes advantage of low cost, and simple and fast operating procedure compared with KES system. The paper is to develop the semi-emprical equation for assessment of the fabric handle measured with nozzle tester on the basis of friction law. The variables considered in the equation arc fabric's frictional coefficient and drape coefficient which is determined in terms of fabric bending length and shear strain. The experiment of 12 different cotton and polyester fabrics and comparisons between experimental and theoretical results were conducted. Fabrics of high frictional coefficients, high bending length, and low shear strain showed high fabric handle forces (low handle values). The handle forces predicted from the equation agreed well with those measured, which indicates that the equation can be used to objectively evaluate fabric handle with respect to fabric's own properties and also provide an information for fabric design to improve the handle performance.

• Journal of Broadcast Engineering
• /
• v.14 no.3
• /
• pp.299-310
• /
• 2009

In this paper, we proposed a new method to correct the zoom lens distortion for the video sequence captured by the zoom lens. First, we defined the nonlinear zoom lens distortion model which is represented by the focal length and the lens distortion using the characteristic that lens distortion parameters are nonlinearly and monotonically changed while the focal length is increased. Then, we chose some sample images from the video sequence and estimated a focal length and a lens distortion parameter for each sample image. Using these estimated parameters, we were able to optimize the zoom lens distortion model. Once the zoom lens distortion model was obtained, lens distortion parameters of other images were able to be computed as their focal lengths were input. The proposed method has been made experiments with many real images and videos. As a result, accurate distortion parameters were estimated from the zoom lens distortion model and distorted images were well corrected without any visual artifacts.