• ETRI Journal
• /
• v.26 no.3
• /
• pp.229-240
• /
• 2004

This paper reports on our development of a dual-mode transceiver for a CMOS high-rate Bluetooth system-onchip solution. The transceiver includes most of the radio building blocks such as an active complex filter, a Gaussian frequency shift keying (GFSK) demodulator, a variable gain amplifier (VGA), a dc offset cancellation circuit, a quadrature local oscillator (LO) generator, and an RF front-end. It is designed for both the normal-rate Bluetooth with an instantaneous bit rate of 1 Mb/s and the high-rate Bluetooth of up to 12 Mb/s. The receiver employs a dualconversion combined with a baseband dual-path architecture for resolving many problems such as flicker noise, dc offset, and power consumption of the dual-mode system. The transceiver requires none of the external image-rejection and intermediate frequency (IF) channel filters by using an LO of 1.6 GHz and the fifth order onchip filters. The chip is fabricated on a $6.5-mm^{2}$ die using a standard $0.25-{\mu}m$ CMOS technology. Experimental results show an in-band image-rejection ratio of 40 dB, an IIP3 of -5 dBm, and a sensitivity of -77 dBm for the Bluetooth mode when the losses from the external components are compensated. It consumes 42 mA in receive ${\pi}/4-diffrential$ quadrature phase-shift keying $({\pi}/4-DQPSK)$ mode of 8 Mb/s, 35 mA in receive GFSK mode of 1 Mb/s, and 32 mA in transmit mode from a 2.5-V supply. These results indicate that the architecture and circuits are adaptable to the implementation of a low-cost, multi-mode, high-speed wireless personal area network.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.43 no.10 s.352
• /
• pp.46-54
• /
• 2006

In this paper, we propose a digital transceiver that can overcome the problems which current analog transceivers have. For the proposed transceiver, we assumed a frequency resource that consists of discrete and narrow channels. We also assumed that person-to-group, group-to-group, as well as person-to-person, voice and data communications with moderate security should be devisedand the data rate is 1 Mbps with simultaneous voice and data. Frequency hewing spread spectrum (FH-SS) and differential 8-PSK (D8PSK) were adopted for security reasons and bandwidth constraints, and for the reduction of implementation complexity, respectively. For the carrier and the symbol timing recovery, the structure of the preamble was proposed based on the IEEE 802.11 FHSS frame format to improve detection probability. The computer simulation results and power budget analysis implies that the proposed system can be usedin simple wireless communications in place of such as analog walkie-talkies.

• BMB Reports
• /
• v.32 no.3
• /
• pp.215-225
• /
• 1999

Phytochromes (with gene family members phyA, B, C, D, and E) are a wavelength-dependent light sensor or switch for gene regulation that underscore a number of photo responsive developmental and morphogenic processes in plants. Recently, phytochrome-like pigment proteins have also been discovered in prokaryotes, possibly functioning as an auto-phosphorylating/phosphate-relaying two-component signaling system (Yeh et al., 1997). Phytochromes are photochromically convertible between the light sensing Pr and regulatory active Pfr forms. Red light converts Pr to Pfr, the latter having a "switch-on" conformation. The Pfr form triggers signal transduction pathways to the downstream responses including the expression of photosynthetic and other growth-regulating genes. The components involved in and the molecular mechanisms of the light signal transduction pathways are largely unknown, although G-proteins, protein kinases, and secondary messengers such as $Ca^{2+}$ ions and cGMP are implicated. The 124-127 kDa phytochromes form homodimeric structures. The N-terminal half contains the tetrapyrrolic phytochromobilin for red/far-red light absorption. The C-terminal half includes both a dimerization motif and regulatory box where the red light signal perceived by the chromophore-domain is recognized and transduced to initiate the signal transduction cascade. A working model for the inter-domain signal communication within the phytochrome molecule is proposed in this Review.

• Journal of Microbiology and Biotechnology
• /
• v.24 no.1
• /
• pp.113-118
• /
• 2014

Environmental microorganisms are emerging as an important source of new enzymes for wide-scale industrial application. In this study, novel phytase genes were identified from a soil microbial community. For this, a function-based screening approach was utilized for the identification of phytase activity in a metagenomic library derived from an agricultural soil. Two novel phytases were identified. Interestingly, one of these phytases is an unusual histidine acid phosphatase family phytase, as the conserved motif of the active site of PhyX possesses an additional amino acid residue. The second phytase belongs to a new type, which is encoded by multiple open reading frames (ORFs) and is different to all phytases known to date, which are encoded by a single ORF.

• The Plant Pathology Journal
• /
• v.24 no.2
• /
• pp.143-151
• /
• 2008

To define the functions of the rpf genes in Xanthomonas oryzae pv. oryzae (Xoo), which regulates pathogenicity factors in Xanthomonas campestris pv. campestris (Xcc), marker-exchange mutants of each rpf gene were generated. When the mutants were inoculated on a susceptible cultivar, the lesion lengths caused by the rpfB, rpfC, rpfF, and rpfG mutants were significantly smaller than those caused by the wild type, whereas those caused by the rpfA, rpfD, and rpfI mutants were not. Several virulence determinants, including extracellular polysaccharide (EPS) production, xylanase production, and motility, were significantly decreased in the four mutants. However, the cellulase activity in the mutants was unchanged. Complementation of the rpfB and rpfC mutations restored the virulence and the expression of the virulence determinants. Expression analysis of 14 virulence genes revealed that the expression of genes related to EPS production (gumG and gumM), LPS (xanA, xanB, wxoD, and wxoC), phytase (phyA), xylanase (xynB), lipase (lipA), and motility (pitA) were reduced significantly in the mutants rpfB, rpfC, rpfF, and rpfG. In contrast, the expression of genes related to cellulase (eglxob, clsA), cellobiosidase (cbsA), and iron metabolism (fur) was unchanged. The results of this study clearly show that rpfB, rpfC, rpfF, and rpfG are important for the virulence of Xoo KACC10859, and that virulence genes are regulated differently by the Rpfs.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.50 no.7
• /
• pp.292-299
• /
• 2013

In this paper, we developed a data transmission system over coaxial cable based on the IEEE 802.15.3 MAC and Ultra-Wideband(UWB) Physical Layer. This system is capable of operation in both wireless and wired medias. When operating on coax cable it is capable of Gigabit bi-directional data rate operation on in-home coax wiring and over Hybrid-Fiber-Coax(HFC) cable infrastructure. The developed system transceives command, control and data over a 75 ohm coax system in a home or office. This system operates at a center frequency of 4GHz with a total occupied bandwidth of 1.33Ghz centered on 4GHz. The system uses BPSK modulation and sends symbols at a maximum power level of +15dBm. It has been tested and works through up to three CATV RF splitters in a home environment.

• The Transactions of the Korean Institute of Electrical Engineers D
• /
• v.55 no.7
• /
• pp.303-312
• /
• 2006

This paper proposes the architecture and protocol of a data communication network for the safety system in nuclear power plants. First, we establish four design criteria with respect to determinability, reliability, separation and isolation, and verification/validation. Next we construct the architecture of the safety network for the following systems: PPS (Plant Protection System), ESF-CCS (Engineered Safety Features-Component Control System) and CPCS (Core Protection Calculator System). The safety network consists of 12 sub-networks and takes the form of a hierarchical star. Among 163 communication nodes are about 1600 origin-destination (OD) pairs created on their traffic demands. The OD pairs are allowed to exchange data only during the pre-assigned time slots. Finally, the communication protocol is designed in consideration of design factors for the safety network. The design factors include a network topology of star, fiber-optic transmission media, synchronous data transfer mode, point-to-point link configuration, and a periodic transmission schedule etc. The resulting protocol is the modification of IEEE 802.15.4 (LR-WPAN) MAC combined with IEEE 802.3 (Fast Ethernet) PHY. The MAC layer of IEEE 802.15.4 is simplified by eliminating some unnecessary (unctions. Most importantly, the optional TDMA-like scheme called the guaranteed time slot (GTS) is changed to be mandatory to guarantee the periodic data transfer. The proposed protocol is formally specified using the SDL. By performing simulations and validations using Telelogic Tau SDL Suite, we find that the proposed safety protocol fits well with the characteristics and the requirements of the safety system in nuclear power plants.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2006.05a
• /
• pp.522-525
• /
• 2006

Recently, mobile devices support multi-functions such as 3D game, wireless internet, moving pictures, DMB, GPS, and PMP. Bigger size of display device is indispensable to support these functions and higher speed of the interface is needed. However, conventional parallel interfaces between processor and display nodule are not competent enough for that high speed transfers. High-speed serial interface is beginning to appear as an alternative for parallel interface. The advantages of the serial interface are high bandwidth, small number of interconnections, low-power consumption, and good quality of electro-magnetic interference. In this paper, we implement serial interface and use it for a display module. LVDS is used for PHY layer and a defined packet is used for link layer. The feature of the implemented serial interface is the reduced number of interconnections with enough bandwidth.

• Progress in Medical Physics
• /
• v.9 no.1
• /
• pp.1-9
• /
• 1998

In order to provide complementary image data, CT(computed tomography), MR(magnetic resonance) and angiography have been used in the field of Stereotactic Radiosurgery(SRS) and neurosurgery. The aim of this work is to develop 3-D stereotactic localization system in order to determine the precise shape, size and location of the lesion in the brain in the field of Stereotactic Radiosurgery(SRS) and neurosurgery using multi-image modality and multi purpose QA phantom. In order to obtain accurate position of a target, Hitchcoke stereotactic frame and CT/angiography localizers were rigidly attached to the phantom with nine targets dispersed in 3-D space. The algorithms to obtain a 3-D stereotactic coordinates of the target have been developed using the images of the geometrical phantom which were taken by CT/angiography. Positions of targets computed by our algorithms were compared to the absolute position assigned in the phantom. Outlines of targets on each CT image were superimposed each other on angiography images. A spatial mean distance errors were 1.02${\pm}$0.17mm for CT with a 512${\times}$512 matrix and 2mm slice thickness, 0.41${\pm}$0.05mm for angiogra- phy localization. The resulting accuracy in the target localization suggests that the developed system has enough Qualification for Stereotactic Radiosurgery (SRS).

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.30 no.11A
• /
• pp.1027-1034
• /
• 2005

IEEE802.15.4a, which is started to realize the PHY layer including high precision ranging/positioning and low data rate communication functions, requires a simple and low power consumable transceiver architecture. To satisfy this requirements, the simple noncoherent on-off keying (OOK) UWB transceiver with the parallel energy window banks (PEWB) giving high precision signal processing interface is proposed. The flexibility of the proposed system in multipath fading channel environments is acquired with the pulse and bit repetition method. To analyze the bit error rate (BER) performance of this proposed system, a noise model in receiver is derived with commonly used random variable distribution, chi-square. BER of $10^{-5}$ under the line-of-sight (LOS) residential channel is achieved with the integration time of 32 ns and signal to noise ratio (SNR) of 15.3 dB. For the non-line-of-sight (NLOS) outdoor channel, the integration time of 72 ns and SNR of 16.2 dB are needed. The integrated energy to total received energy (IRR) for the best BER performance is about $86\%$.