• Journal of Astronomy and Space Sciences
• /
• v.37 no.4
• /
• pp.237-247
• /
• 2020

The ground tracking support is a critical factor for the navigation performance of spacecraft orbiting around the Moon. Because of the tracking limit of antennas, only a small number of facilities can support lunar missions. Therefore, case studies for various ground tracking support conditions are needed for lunar missions on the stage of preliminary mission analysis. This study analyzes the ground supporting condition effect on orbit determination (OD) of Korea Pathfinder Lunar Orbiter (KPLO) in the lunar orbit. For the assumption of ground support conditions, daily tracking frequency, cut-off angle for low elevation, tracking measurement accuracy, and tracking failure situations were considered. Two antennas of deep space network (DSN) and Korea Deep Space Antenna (KDSA) are utilized for various tracking conditions configuration. For the investigation of the daily tracking frequency effect, three cases (full support, DSN 4 pass/day and KDSA 4 pass/day, and DSN 2 pass/day and KDSA 2 pass/day) are prepared. For the elevation cut-off angle effect, two situations, which are 5 deg and 10 deg, are assumed. Three cases (0%, 30%, and 50% of degradation) were considered for the tracking measurement accuracy effect. Three cases such as no missing, 1-day KDSA missing, and 2-day KDSA missing are assumed for tracking failure effect. For OD, a sequential estimation algorithm was used, and for the OD performance evaluation, position uncertainty, position differences between true and estimated orbits, and orbit overlap precision according to various ground supporting conditions were investigated. Orbit prediction accuracy variations due to ground tracking conditions were also demonstrated. This study provides a guideline for selecting ground tracking support levels and preparing a backup plan for the KPLO lunar mission phase.

• Journal of the Korean Society for Heat Treatment
• /
• v.4 no.4
• /
• pp.24-33
• /
• 1991

The effects of thermomechanical treatments on microstructure and fatigue properties of 7050 Al alloy were investigated. The precipitation kinetics changed to a faster rate due to cold deformation employed in this special TAHA thermomechanical treatments including pre-aging, plastic deformation and two step final-aging. The G.P. zones in the under-aged condition were cut by dislocations and dissolved during the plastic deformation. During the low cycle fatigue, the T6' condition showed cyclic hardening behavior whereas the TMT5, TMT27 and T76 conditions showed cyclic softening at above 0.7% total strain amplitudes. The ${\Delta}K_{th}$ value of TMT27 was improved more than two times, compared with that of T76 condition. The T6' with small shearable precipitates resulted in the markedly high ${\Delta}K_{th}$ value. This is thought to be resulted from dislocation reversibility and roughness-induced crack closure due to planarity of slip.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2000.11a
• /
• pp.866-869
• /
• 2000

To improve quality of the ground surface, we have to consider a number of parameters. But it is difficult to make experiment with many parameters. Most of all experiments try to search optimal grinding condition with conservative factors such as feed rate, depth of cut, wheel rotating speed, etc. But This paper attempts to view the significance of some different factors effecting on the surface roughness by introducing helical scan grinding method and material removal rate. The design of experiment is used to find the optimal grinding condition which minimizes the surface roughness value bout optical glass material. To analyze experimental results, ANOVA(ANalysis of VAriation) is used. Discussion on the result about helical scan grinding is also given.

• Proceedings of the KSME Conference
• /
• 2003.11a
• /
• pp.1822-1827
• /
• 2003

End-milling have been used widely in industrial system because it is effective to a material manufacturing with various shape. Recently the end-milling processing is needed the high-precise technique with good surface roughness and rapid time in precision machine part and electronic part. The optimum surface roughness has an effect on end-milling condition such as, cutting direction, spindle speed, feed rate and depth of cut, etc. Therefore this study was carried out to presume for mutual relation of end-milling condition to get the optimum surface roughness by regression analysis. The results shown that coefficient of determination($R^{2}m$) of regression equation has a fine reliability over 80% and regression equation of surface rough is made by regression analysis.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.12 no.5
• /
• pp.46-52
• /
• 2003

End-milling have been used widely in industrial system because it is effective to a material manufacturing with various shape. Recently the end-milling processing is needed the high-precise technique with good surface roughness and rapid time in precision machine part and electronic part. The optimum surface roughness has an effect on end-milling condition such as, cutting direction spindle speed, feed rate and depth of cut, etc. Therefore this study was carried out to presume for mutual relation of end-milling condition to get the optimum surface roughness by regression analysis. The results shown that coefficient of determination($\textrm{R}^2$) of regression equation has a fine reliability of 87.5% and regression equation of surface rough is made by regression analysis.

• Proceedings of the Korean Society of Marine Engineers Conference
• /
• 2001.05a
• /
• pp.207-212
• /
• 2001

In this paper, a method to be able to decide the possible maximum gain of P, PI control for the retarded processes under stable condition is proposed. At first, adjustable parameter set causing stability limit are obtained based on the frequency domain condition which makes the roots of transfer function locate on the $j\omega$ axis. And the cut-in frequency $\omega{_p}$ to bring the parameter set to P control from PI control is derived by an equation with 2 parameters L and $T_m$ given, then $\omega{_p}$ is used to compute the maximum gain with stable condition. For the calculation, the controlled process of first order system with time delay element is introduced and all parameters are presumed to be time invariant.

• Korean Journal of Environmental Agriculture
• /
• v.17 no.4
• /
• pp.358-361
• /
• 1998

This study was carried out to develop a short term hardening method of tree seedlings of Rhus chinensis Mill., Evodia daniellii Hemsley and Parthenocissus tricuspidata(Sieb. et Zucc.) Planck for afforestation on a concave and a crack of cut-rock slope. The seedlings were grown in a cylinder shaped pot made of polyvinyl net with the soil media of peatmoss, vermiculite, clay, compost, fertilizer, and absorbant(40:25:19:15:1:0.1, v:v). They were cultivated in a greenhouse for four months and in field condition for two months. During the last three months of the growing period the seedlings were hardened by periodic desiccation and irrigation in 4 to 10 days interval. The hardened seedlings showed lower leaf water potential, higher leaf osmotic pressure, and lower T/R ratio than those before the hardening. The hardened seedlings survived well on the soil medium in the concave of cut-rock slope.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2005.10a
• /
• pp.564-569
• /
• 2005

Usually, Steel pipe grouting method or cut and cover method has been applied to tunnel with very shallow overburden or it is situated in valley. However, in case of lack of overburden height to reinforcement tunnel crown which is very difficult to construction. Also, application of cut and cover method that do not consider surrounding site condition causes popular enmity generation and environmental damage. It is the best alternative method that reduces the amount of excavated soil and excavate tunnel under ground to solve these problems. The tunneling method using cover structure which is to prevent a tunnel from collapse because this method can be reduce excavation area and construct tunnel under ground after set a cover structure and backfill ground. In this study, to know more effective structure type, comparative analysis was performed to behavior characters of slab and arch type construction that can be used to cover structure. Also a 2D and 3D numerical analysis have been performed to verify the stability of ground during excavation. As the result, the tunneling method using cover structure that it can be good alternative method for tunnel with shallow overburden and it through valley

• Journal of Biosystems Engineering
• /
• v.42 no.1
• /
• pp.12-22
• /
• 2017

Purpose: This aim of this study was to develop a pick-up type pulse crop harvester for harvesting cut and dried pulse crop. Methods: The pick-up type pulse crop harvester was designed and constructed. Its specifications and operating performance were investigated. Results: Compared with conventional bean harvesters, the pick-up type pulse crop harvester adopted seven rows of chains with tines to pick-up the cut and dried pulse crop on a flat or ridged field, two transverse threshing drums with steel wire teeth to reduce the threshing speed, and a tilt plate and plastic bucket elevator for conveying clean grain to reduce damage. The threshing speed and the oscillating frequency of the separating and cleaning parts according to crop type and condition could be varied easily to efficiently use engine power and to improve harvesting performance. The harvester showed forward speed ranges of 0 ~ 1.5 m/s during harvesting operation, and 0 ~ 2.5 m/s during road travelling. The pick-up width of the harvester was about 1 m. Conclusions: The pick-up type self-propelled 51.5 kW harvester was designed and constructed to harvest cut and dried pulse crop. The effective field capacity of the harvester was predicted as above 40 a/h.

• Korean Journal of Medicinal Crop Science
• /
• v.16 no.6
• /
• pp.421-426
• /
• 2008

Three year-old peony (Paeonia. lactiflora Pall. cv. Taebaek) was cultivated in green-house at Jan. 15, Feb. 15, or Mar. 15, respectively. The mean of temperature during the forcing cultivation was higher (air; $1.0{\sim}11.1^{\circ}C$, soil; $1.1{\sim}7.4^{\circ}C$) than that of open-field condition. From sprouting to flowering in peony cultivated at Jan. 15 was about 54 days, which is shorted the cut flower periods (ca. 26 days) compared with the open-field cultivation. However, earlier forcing cultivars were very susceptible to pathogens such as powdery mildew or gray mold. The yield in green house was also lower than in the open-field cultivation. The content of bioactive compounds such as paeoniflorin and albiflorin in green-house cultivars was similar that of open-field cultivars. These results showed the forcing cultivation time of peony at Feb. 15 in green-house was most desirable for commercialization.