• Tribology and Lubricants
• /
• v.35 no.1
• /
• pp.52-58
• /
• 2019

In the case of high-voltage connectors applied to automobiles, waterproofing has become an important issue for the safety of automobiles. In this study, structural analysis is performed on silicone rubber-type waterproof seals used in the voltage connector. For the structural analysis, the tensile properties of the actual rubber seal are evaluated using a miniaturized tensile testing machine. The Mooney-Rivlin material constants of the rubber seal are determined as follows; $D_1=0$, $C_{01}=0.241$, $C_{10}=0.0142$. The analysis shows that the contact pressure at the top of the seal where the seal and male connector are in contact is approximately three times higher than that at the bottom of the seal where the seal and female connector are in contact. It is confirmed that the waterproofing performance of the rubber seal depends on the contact pressure of the seal bottom where the seal and female connector are in contact. The contact pressure for waterproofing is found to be 4.7 bar. The strain concentration of the curved part is attributed to excessive initial tension. Therefore, a redesign is recommended for uniform stress or strain distribution in the curved section of the seal in response to the stress relaxation problem due to permanent deformation.

• Plant Journal
• /
• v.17 no.3
• /
• pp.42-46
• /
• 2021

The equation of motion of the drill string along the excavation trajectory was analyzed using the Lagrangian approach together with the finite element method (FEM). A drill string of circular cross section is constructed by combining a plurality of circular axes each having 12 degrees of freedom (DOF). FEM analysis can observe the vibration and dynamic changes of the entire drill string, and it is easy to apply comprehensive boundary conditions to reproduce the simulation of a realistic drill string. In this study, the constructed FEM motel was simulated. In order to apply the FEM program to the actual drill trajectory, the dynamic analysis of the curved beam was verified by comparison with the actual values. The dynamic change over time was observed.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.39 no.5
• /
• pp.491-497
• /
• 2015

This paper reports an experimental study for evaluating the effect of temperature on the mode I, mode II and mixed-mode interlaminar fracture toughness of adhesive joints with a curved cross-section of filament-wound dome-separated composite pressure vessel. Mode I and mixed-mode interlaminar fracture toughness were evaluated using DCB specimens, while mode II interlaminar fracture toughness was determined using ENF specimens. $[{\pm}10^{\circ}]_6$, $[{\pm}27^{\circ}]_6$ and ($[{\pm}10^{\circ}]_3/FM73/[{\pm}27^{\circ}]_3$) winding specimens with the curved cross-section were considered. In-situ temperature environments were simulated with a range of $-30^{\circ}C-60^{\circ}C$ using an environmental chamber and furnace. Experimental results on the effect of temperature indicate that interlaminar fracture toughness tends to be high at low temperature and is degraded with increase in temperature. For specimen types, it was found that interlaminar fracture toughness of $[{\pm}10^{\circ}]_3/FM73/[{\pm}27^{\circ}]_3$ winding specimens considered as adhesive joints of dome and helical part was higher than other specimens.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.14 no.8
• /
• pp.4068-4076
• /
• 2013

The wheel-rail interaction forces are influenced by the velocity of vehicle, wheel load, alignment (curve radius, cant etc). For the safety of track structure, it is required to evaluate the influences for track and influential factors. Recently, the HEMU 430-X, which was developed by Next Generation High-Speed Rail Development R&D Project, achieved 421.4km/h in a test run of Daegu.Busan section of the Gyeongbu high speed rail on March in 2013. In the case of additional speed-up test on Test-Bed Section(Gongju.Jeongeup: KP 100~128km Osong starting point), the analysis of track forces is required for outer rail by the increase of dynamic force and centrifugal force of vehicle. In this paper, the vehicle speed variation on HSL line is evaluated by TPS analysis considering the tractive effort of HEMU 430-X, tested running resistance and alignment of Honam HSR. And the track forces are evaluated by centrifugal force and impact factor on curved track.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.10
• /
• pp.739-744
• /
• 2017

Elastic deformation and fatigue damage can cause the permanent deformation of a kart's frame during turning, affecting the kart's driving performance. A kart's frame does not contain any suspension or differential devices and, therefore, the dynamic behavior caused by torsional deformation when driving along a curve can strongly affect these two kinds of deformations. To analyze the dynamic behavior of a kart along a curved section, the GPS trajectory of the kart is obtained and the torsional stress acting on the kart-frame is measured in real time. The mechanical properties of leisure and racing karts are investigated by analyzing their material properties and conducting a tensile test. The torsional stress concentration and frame distortion are investigated through a stress analysis of the frame on the basis of the obtained results. Leisure and racing karts are tested in each driving condition using driving analysis equipment. The behavior of a kart when being driven along a curved section is investigated through this test. Because load movement occurs owing to centrifugal force when driving along a curve, torsional stress acts on the kart's steel frame. In the case of a leisure kart, the maximum torsional stress derived from the torsional fatigue limit was found to be 230 MPa, and the torsional fatigue limit coefficient was 0.65 when driving at a speed of 40 km/h. Furthermore, the driving elements during the cornering of a kart were measured based on an actual auto-test after installing a driving measurement system, and the driving behavior of the kart was analyzed by measuring its vertical displacement.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.16 no.3
• /
• pp.73-82
• /
• 2017

As of December 2016, the number of registered automobiles in Korea exceeds 21million. As a result, greenhouse gas emission by transportation sector are increasing every year. It was concluded that the development of the driving strategy considering the driving behavior and the road conditions, which are known to affect the fuel efficiency and the greenhouse gas emissions, could be the most effective fuel economy improvement. Therefore, this study aims to develop a fuel efficient driving strategy in a complex linear section with uphill and curved sections. The road topography was designed according to 'Rules about the Road Structure & Facilities Standards'. Various scenarios were selected. After generating the speed profile, it was applied to the Comprehensive Modal Emission Model and fuel consumption was calculated. The scenarios with the lowest fuel consumption were selected. After that, the fuel consumption of the manual driver's driving record and the selected optimal driving strategy were compared and analyzed for verification. As a result of the analysis, the developed optimal driving strategy reduces fuel consumption by 21.2% on average compared to driving by manual drivers.

• The Korean Journal of Cytopathology
• /
• v.7 no.2
• /
• pp.169-176
• /
• 1996

This study was peformed in order to evaluate the usefulness of the crush cytologic features and differential diagnosis between meningiomas and schwannomas in the central nervous system. Deeply seated and unusually located meningiomas and schwannomas with equivocal or erroneous frozen section diagnosis can be correctly diagnosed cytologically in crush preparations. Twenty-four meningiomas and nine schwannomas were studied by frozen section and crush preparation technique. These tumors displayed distinctive cytologic features. in meningiomas, the tumor tissue fragments were easy to crush, and the tumor cells were arranged in small clusters, flat sheets, papilla-like, whorling pattern or singly. Individual tumor cells displayed round or oval nuclei with finely granular chromatin pattern and inconspicuous small nucleoli. Occasionally psammoma bodies, nuclear pseudoinclusion or nuclear grooves were found. In schwannomas, tissue fragments were hard in consistency and difficult to crush. The crushed tissue presented as thick, irregular fragments with shard borders. The cells showed ill-defined cytoplasm and round, oval, cigar-shaped or curved nuclei. It is important to emphasize that the smear pattern under low-power view and cytologic features are helpful in discriminating between these two tumors.

• Journal of the Korean Society of Costume
• /
• v.66 no.8
• /
• pp.46-60
• /
• 2016

Countries have different brassiere patterns, and this study produced and compared 3/4 brassiere patterns from different countries to determine the difference in patterns, and to investigate the stress distribution and shape of cross section while wearing brassieres using 3D virtual fitting system. Despite the growing interest in underwear, there is a lack of related books and research on brassiere patterns, which causes the difference in sizes and pattern drafting methods by countries. Thus, research on this is needed. 3D virtual fitting system has been introduced to compare patterns, thereby improving visible effects and reducing the loss in cost caused by underwear pattern fitting test. According to the result of pattern analysis, The Secoli type exhibited the least breast cover rate (14.9 cm), while the largest cover rate was shown in Christina and ESMOD types (17.7 cm). It is believed that the difference in pattern drafting causes the difference in the total length of a brassiere. Furthermore, the Secoli, Moda Burgo, and ESMOD brassieres drafted from basic bodice pattern were found to be longer than the Christina and Han Sunmi brassieres attained from direct pattern drafting. Moreover, the darts' volume of upper and lower cups in Christina and Han Sunmi types was similar in shape. The shapes of cradle drafted from basic bodice pattern were a straight line, while those from direct drafting formed a curved shape. In fitting multiple cross sections, the Secoli, Moda Burgo, and ESMOD brassieres had gaps between the brassieres and the body. Among these, the largest number of gaps was observed in the ESMOD type pattern. This study aimed at performing comparative analysis of various brassieres' pattern drafting types as a basic research for developing a brassiere pattern drafting type.

• Proceedings of the Korean Society of Computer Information Conference
• /
• 2011.01a
• /
• pp.107-108
• /
• 2011

Since the development of railway technology, the current urban Railway the first train line in the country for safe operation control automatic/unattended operation, automatic train operation equipment available (ATO) on time and reliable operation has introduced. ATO Automatic operation controlled by the value (Target velocity) and the feedback value (Actual velocity) by the error between the backing and braking of the train by repeated low energy efficiency. In this paper, given a fixed distance stations between time operation with minimal energy in the driving characteristics and driving trains are modeled. Therefore, in line 5 real route time sectional drive straight sections for experimental data analysis / draft Section / curved and section of the train on that line is selected according to the changing driving patterns to minimize the energy optimal driving patterns were presented.

• Journal of architectural history
• /
• v.31 no.6
• /
• pp.59-68
• /
• 2022

This paper is an architectural historical study on Chimi of Hwangnyongsa Temple. In this research, the shape and cross-section of the chimi are reviewed. The results of the study are as follows. The chimi is a form in which the head part facing the maru is omitted, and the upper and lower body are separated. The upper and lower bonds are assembled into a two types of joint throughout the side of the torso, and then bound with an iron strap. Because of the absence of ridge line in the front, and the narrow curved surface which makes the side plate close to the plane, the entire cross-section is triangular, and the rear plate maintains the shape of the chimi. The naerimmaru connected to the side of the chimi has a slope, so it is clear that the chimi was used on the woojingak-jibung(hipped-roof), and the wing part and back of the chimi are erected on the side roof. The height of the yongmaru and chunyeomaru is about the same and the roofing tiles of those are in contact. The roofing tiles of chunyemaru should be cut to fit the angle of the contacting part. The maru is 30 stories high of roofing tiles as a result of the on-board survey. Based on reference on the shape and timing of the production of chimi, the height of chimi, and the maru is believed to have been built before the Unified Silla Period and used in buildings with at least seven-kan frontage. Buildings corresponding to these construction conditions can be seen as Central hall and East hall in Hwangnyongsa temple.