• 한국공간구조학회논문집
• /
• 제6권1호
• /
• pp.117-127
• /
• 2006

경량 연성구조시스템 중 하나인 막 구조물은 대공간 구조물에 많이 사용되어진다. 막 구조물은 축강성이 강하고 휨강성이 매우 작은 재료를 주 구조재로 사용하기 때문에 다른 구조물과 달리 구조설계에서는 형상해석, 응력-변형해석 그리고 재단도 등의 일련의 과정을 필요로 한다. 재단도의 작성에는 구조물의 크기나 곡률 그리고 재료적 강성에 따라 많은 변수가 작용하며 다른 설계과정과는 매우 다르다. 따라서 일반 구조설계용 프로그램은 막 구조물의 구조설계에 부적당하다. 본 연구에서는 막 구조물의 측지선을 이용한 재단도 작성 프로그램을 개발하고, 예제를 통해 재단도 작성결과를 비교 고찰하도록 한다.

• 대한기계학회논문집B
• /
• 제31권12호
• /
• pp.1024-1032
• /
• 2007

The flow characteristics with the impinging angles of defrost nozzle jet inside a commercial vehicle passenger compartment were investigated experimentally by using the two-dimensional duct-nozzle model. The shape of the nozzle contraction was designed according to the curved line of cubic equation to the vertical plan of the flow direction. The impinging angles, defined as the angle between nozzle axis and a vertical line to the windshield, were varied from the $0^{\circ}\;to\;80^{\circ}$. The mean velocity distributions, the half-widths, and the momentum distributions with the cases of both the free jet and the impinging jet onto the dummy windshield were measured. The impinging jet flows similarly with wall jet from $X/b_o=20$, and the impinging angle has an effect on the half-width of the impinging jet. The momentum distributions onto the windshield increased with the increase of impinging angle, and then their inflection point was observed around the impinging angle of $60^{\circ}$.

• 한국컴퓨터정보학회논문지
• /
• 제23권4호
• /
• pp.57-64
• /
• 2018

In this paper, we propose the automatic detection method for individual region separation using panorama image. Finding areas that contain individual teeth is one of the most important tasks in automating 3D models through individual tooth separation. In the conventional method, the maxillary and mandibular teeth regions are separated using a straight line or a specific CT slide, and the tooth regions are separated using a straight line in the vertical direction. In the conventional method, since the teeth are arranged in a curved shape, there is a problem that each tooth region is incorrectly detected in order to generate an accurate tooth region. This is a major obstacle to automating the creation of individual tooth models. In this study, we propose a method to find the correct tooth curve by using the jawbone curve which is very similar to the tooth curve in order to overcome the problem of finding the area containing the existing tooth. We have proposed a new method to accurately set individual tooth regions using the feature that individual teeth are arranged in a direction similar to the normal direction of the tooth alignment curve. In the proposed method, the maxillary and mandibular teeth can be more precisely separated than the conventional method, and the area including the individual teeth can be accurately set. Experiments using real dental CT images demonstrate the superiority of the proposed method.

• 한국안전학회지
• /
• 제31권3호
• /
• pp.130-135
• /
• 2016

It is very hard to analyze the train derailment safety quantitatively at the curved section because of the diversified affect parameters including the complex interaction between wheel and rail, the train conditions such as the shape of wheel, suspension system, the track conditions such as the radius of curve, cant, transition curve, and the operation conditions, etc. Two major factors related to the running safety of railway vehicle are classified as the railway vehicle and the track condition. In this study, when the railway vehicle passing through curves of actual track condition of subway line NO.3 in seoul ($Yeonsinnae{\leftrightarrow}Gupabal$), the effect that has influence on running safety depending on rail inclination. The analysis result of 1/40 rail inclination condition is more favorable on running safety than other rail inclination conditions because derailment coefficient and wheel unloading ratio are the lowest.

• 복식
• /
• 제66권8호
• /
• pp.46-60
• /
• 2016

Countries have different brassiere patterns, and this study produced and compared 3/4 brassiere patterns from different countries to determine the difference in patterns, and to investigate the stress distribution and shape of cross section while wearing brassieres using 3D virtual fitting system. Despite the growing interest in underwear, there is a lack of related books and research on brassiere patterns, which causes the difference in sizes and pattern drafting methods by countries. Thus, research on this is needed. 3D virtual fitting system has been introduced to compare patterns, thereby improving visible effects and reducing the loss in cost caused by underwear pattern fitting test. According to the result of pattern analysis, The Secoli type exhibited the least breast cover rate (14.9 cm), while the largest cover rate was shown in Christina and ESMOD types (17.7 cm). It is believed that the difference in pattern drafting causes the difference in the total length of a brassiere. Furthermore, the Secoli, Moda Burgo, and ESMOD brassieres drafted from basic bodice pattern were found to be longer than the Christina and Han Sunmi brassieres attained from direct pattern drafting. Moreover, the darts' volume of upper and lower cups in Christina and Han Sunmi types was similar in shape. The shapes of cradle drafted from basic bodice pattern were a straight line, while those from direct drafting formed a curved shape. In fitting multiple cross sections, the Secoli, Moda Burgo, and ESMOD brassieres had gaps between the brassieres and the body. Among these, the largest number of gaps was observed in the ESMOD type pattern. This study aimed at performing comparative analysis of various brassieres' pattern drafting types as a basic research for developing a brassiere pattern drafting type.

• 한국도로학회논문집
• /
• 제10권4호
• /
• pp.247-255
• /
• 2008

현행 도로설계의 기준이 되는 "도로의 구조 시설 기준에 관한 규칙 해설 및 지침"에서는 설계속도에 따라 도로 선형별 최소 설계기준을 정하고 있으며, 이 기준을 만족시키면 교통안전성 이 확보되는 것으로 규정하고 있다. 이러한 설계기준에 적용되고 있는 개별 설계요소들은 원칙적으로 차량 및 운전자 특성을 감안하여 설치기준이 정립되었으나, 설계요소간의 연관성 또는 일관성에 대한 깊이 있는 연구를 통해 제반 기준이 정립된 것은 아니다. 결과적으로, 현재의 도로설계기준이 개별 설계 요소들의 조합에 의해 결정되는 도로의 안전성, 일관성 문제를 모두 고려하지는 못하였다. 따라서, 본 연구에서는 기존의 설계기준에 내재된 문제점을 인지하고 해결을 위해 우선적으로 3차원 가속도를 고려한 선형 설계방안에 대한 연구를 수행하였으며, 이를 통해 더욱 안전하고 조화로운 도로건설을 유도하고자 한다.

• 한국지형학회지
• /
• 제27권3호
• /
• pp.105-121
• /
• 2020

There has been a lot of controversy over the claim that ancient characters were engraved on a stone plane collected near the Samsin Mountain in Hadong-gun, and that it was used as an altar based on the contents on the stone. The importance of the role of geoscience in prehistoric petroglyph research was presented through analysis and comparison with representative domestic petroglyphs. First, by examining the geological formation process of the collected stone objects, it proved that prehistoric actions were not applied. Second, as a result of comparative analysis from the viewpoints of human geography and topography with representative petroglyphs in Korea, it is unreasonable to argue that the stone was made for an altar. Third, it is considered that among the ancient characters under debate, the straight line indicates a cleavage of carbonate minerals, and the curved shape results from the growth of lichens. Finally, we propose that reproducing the lines found on the stone was impossible by using ancient techniques, and that there was no trace of any artificial actions applied to the spots considered to be curved characters. As shown in such research cases, the results of petroglyph research will have high reliability, if research by experts in each field continues after the geoscientific basis is secured. In this respect, the contribution of Earth science to cultural assets and archeology is expected to increase in the future.

• 한국해양공학회지
• /
• 제22권6호
• /
• pp.75-82
• /
• 2008

Flame bending has been extensively used in the shipbuilding industry for hull plate forming In flame bending it is difficult to obtain the desired shape because the residual deformation dependson the complex temperature distribution and the thermal plastic strain. Mechanical bending such as reconfigurable press forming multi-point press forming or die-less forming has been found to improve the automation of hull plateforming because it can more accurately control the desired shape than line heating. Multi-point forming is a process in which external forces are used to form metal work-pieces. Therefore it can be a flexible and efficient forming technique. This paper presents an optimal approach to determining the press-stroke for multi-point press forming of curved shapes. An integrated configuration of Finite element analysis (FEA) and spring-back compensation algorithm is developed to calculate the strokes of the multi-point press. Not only spring-back is modeled by elastic plastic shell elements but also an iterative algorithm to compensate the spring-back is applied to adjust the amount of pressing stroke. An iterative displacement adjustment (IDA) method is applied by integration of the FEA procedure and the spring-back compensation work. Shape deviation between the desired surface and deform￡d plate is minimized by the IDA algorithm.

• 대한조선학회 특별논문집
• /
• 대한조선학회 2011년도 특별논문집
• /
• pp.32-35
• /
• 2011

Template has been widely used for hull forming process in most of shipyards. It is used to estimate the curvature of deformed shape in comparison with design shape. SHI (Samsung Heavy Industry) had used AutoKon system for ship manufacturing design in the past. The AutoKon used the global coordinate system of ship (frame, water line and so on) to create template data. It brought the mismatched angles between templates and a curved shell plate. The mismatched angle is measured by forming worker to place template on shell forming stage. However, the mismatched angle is difficult to place template with exactly required angle because the shell plates have various curvature and size. It causes incorrect shape of formed shell plates. The attached angle of template should be 90 degree to place template easily on forming shell plates. Currently, SHI has been applied GSCAD for ship manufacturing design process which is 3D solid modeling system. The GSCAD is the rule-based system which can automate 3D modeling and control the manufacturing data by rule. The rule can easily provide methods to create and automate template object with regular attached angle in comparison with AutoKon system. Therefore, SHI developed new template rule which it can automatically create template object with regular attached angle in GSCAD.

• 건축역사연구
• /
• 제31권6호
• /
• pp.59-68
• /
• 2022

This paper is an architectural historical study on Chimi of Hwangnyongsa Temple. In this research, the shape and cross-section of the chimi are reviewed. The results of the study are as follows. The chimi is a form in which the head part facing the maru is omitted, and the upper and lower body are separated. The upper and lower bonds are assembled into a two types of joint throughout the side of the torso, and then bound with an iron strap. Because of the absence of ridge line in the front, and the narrow curved surface which makes the side plate close to the plane, the entire cross-section is triangular, and the rear plate maintains the shape of the chimi. The naerimmaru connected to the side of the chimi has a slope, so it is clear that the chimi was used on the woojingak-jibung(hipped-roof), and the wing part and back of the chimi are erected on the side roof. The height of the yongmaru and chunyeomaru is about the same and the roofing tiles of those are in contact. The roofing tiles of chunyemaru should be cut to fit the angle of the contacting part. The maru is 30 stories high of roofing tiles as a result of the on-board survey. Based on reference on the shape and timing of the production of chimi, the height of chimi, and the maru is believed to have been built before the Unified Silla Period and used in buildings with at least seven-kan frontage. Buildings corresponding to these construction conditions can be seen as Central hall and East hall in Hwangnyongsa temple.