• 한국정밀공학회지
• /
• 제14권6호
• /
• pp.52-63
• /
• 1997

Non-circular gear has a good velocity ratio in high speed and heavy load without any slip, moreover, it can transmit various motion, using simpler structure than link and cam, automation mechainism. In case of designing and manufacturing non-circular gear. I suggest one of references in applying non-circular gear to industrial plant, and suitable range of application by pressure angle curvature and angle ratio

• 한국정밀공학회지
• /
• 제17권8호
• /
• pp.113-119
• /
• 2000

There are two major factors which affect the cam design : the pressure angle and the radius of curvature, Cam shape will have an instantaneous radius of curvature at every point. Even though the design constraint of the pressure angle has been satisfied the follower may still not complete the desired contact motion. If the radius of the follower roller is larger than the concave(negative) radius on the cam it occurs the gap between the cam and the follower roller at the contact point. And also if the curvature of the pitch curve of the cam is too sharp the cam profile may be undercut. This paper proposes a new approach which uses the relative velocity of the follower roller parallel to the tangent line at the contact point on the cam surface for determining the pressure angle and the relative acceeration for determining the radius of curvature.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집E
• /
• pp.819-824
• /
• 2001

Mean velocity and Reynolds stress components of the developing turbulent flows in a rotating 90 degree bend with square cross-section were measured by a hot-wire anemometer. Effects of the centrifugal and Coriolis forces generated by the curvature and rotation of bend on the mean motion and turbulence structures are investigated experimentally. Results show that the Coriolis force associated with the rotation of the bend may act both through the mean motion and turbulent structures, thereby changing the pressure fields, mean and turbulent velocities distributions.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2007년도 추계학술대회 논문집
• /
• pp.107-114
• /
• 2007

In this paper, the equations of motion by which the natural vibration of rotating thick ring can be analyzed accurately are presented. These equations are derived from the theory of finite deformation and the principle of virtual work. The effects of variation in curvature across the ring cross-section can be considered in these equations. The ring models are called as thick ring model and thin ring model respectively as the effects of variation in curvature are considered or neglected. The radial displacement of ring which is rotating at constant angular velocity is determined by a non-linear equation derived from the principle of virtual work. The equations of the in-plane and out-of-plane vibrations at disturbed state are also formulated from the principle of virtual work. They can be expressed as the combination of the radial displacement at the steady state and the disturbed displacements about the steady state. The natural vibrations of rings with different thickness are analyzed by using the presented ring models and 3-dimensional finite element method to verify accuracy of the presented equations of motion. Its results are compared and discussed.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2005년도 추계 학술발표회 제17권2호
• /
• pp.17-20
• /
• 2005

Moment-curvature relation of RC pier is influenced greatly in occurrence form of crack and difference is happened according to consideration existence and nonexistence of tension stiffening effect. However, studies considering these is very insufficient misgovernment. Also, it is sometimes unavoidable lap splice of axial reinforcement in plastic hinge region of RC piers. However, specific design standard about lap splice of axial reinforcement is unprepared real condition and study about effect that lap splice of axial reinforcement get in occurrence form of crack is insufficient misgovernment. Therefore, in this paper, experiments are performed with hollow RC piers that do lap splice of axial reinforcement by main variable. And this study present analytical method about moment-curvature relation of hollow RC pier that consider tension stiffening effect and analyze effect that lap splice of axial reinforcement gets in occurrence form of crack. Analytic method of moment-curvature relation of RC pier that present in this study shows very similar motion with experiment result and crack interval of RC pier is suffering dominate impact in the augmented reinforcement amount by lap splice and average crack interval decreases as lap splice ratio increases.

• 대한의용생체공학회:의공학회지
• /
• 제32권3호
• /
• pp.230-236
• /
• 2011

The aim of this study was to investigate the alteration of lumbar spine and trunk postures on different load-carrying types and amounts under static loading. Two load-carrying types(unilateral carrying: UC vs. bilateral carrying: BC) and four different loads(0, 5, 10, and 15 kg) were randomly tested in this study. Carrying a heavy bag would affect human body posture, specifically lumbar spine curvature, which is considered as one of sources of back problems. Previous studies have not paid attention to the approach of the multisegment model of the lumbar spine and trunk. This study separated two compartments of trunk segment(the lumbar and thorax) in the analysis. The multisegment model of the lumbar spine in addition to Helen-Hayes marker set was used. Eight motion analysis cameras and a force plate were utilized. Ten male subjects(mean mass, $70.6{\pm}3.97$ kg; mean height, $178{\pm}4.18$ m) having no musculoskeletal disease participated in this study. We analyzed trunk angles in three anatomical planes and the spinal curvature in sagittal and frontal planes. Increased loading in both UC and BC significantly resulted in increases in trunk forward lean but only UC induced increases in trunk lateral lean. In addition, increased loading in BC produced flatten lumbar curvature in sagittal plane. As far as coupling motion, subjects tended to use axial rotation of the lumbar spine in transverse plane in response to increased UC loading. Finally, it is concluded that the increased static loading in UC rather than in BC tends to causes combined alterations of the spinal postures(sagittal and transverse planes together), which would be vulnerable to improper mechanical stresses on the spine.

• 한국방재학회:학술대회논문집
• /
• 한국방재학회 2008년도 정기총회 및 학술발표대회
• /
• pp.265-268
• /
• 2008

The safety of a tunnel under seismic motion is most often evaluated by ovalling deformation of tunnel. This paper research about tunnel's longitudinal deformation. Because of spatial variation of seismic ground motion, the longitudinal structures like tunnel are likely to experience relative displacements along longitudinal direction. The spatially variable ground motion can be estimated by coherency function obtained empirically, and can be considered from different arrival times of ground motion. As a result of estimating tunnel's relative displacements at maximum curvature of tunnel, the displacements and curvatures estimated by coherency function affect the tunnel's safety more than different arrival times. However, if tunnel's displacements by coherency function superpose on displacements by different arrival times, the relative displacements and curvatures of tunnel will be more severe. Therefore, to estimate accurately tunnel's deformation in longitudinal direction has to consider both coherency and wave passage effects.

• 한국기계가공학회지
• /
• 제10권2호
• /
• pp.104-109
• /
• 2011

I present a method of aspheric surface profile measurement using 2nd derivative of local area profile. This method is based on the principle of curvature sensor which measures the local 2nd derivative under test along a line. The profile is then reconstructed from the data on the each point. Unlike subaperture-stiching method and slope detection method, 2nd derivative method has strong points from a geometric point of view in measuring the aspheric surface profile. The second derivative terms of surface profile is an intrinsic property of the test piece, which is independent of its position and tip-tilt motion. The curvature is measured at every local area with high accuracy and high lateral resolution by using White-light scanning interferometry.

• 대한수학회지
• /
• 제53권5호
• /
• pp.1077-1100
• /
• 2016

We develop an invariant local theory of Lorentz surfaces in pseudo-Euclidean 4-space by use of a linear map of Weingarten type. We find a geometrically determined moving frame field at each point of the surface and obtain a system of geometric functions. We prove a fundamental existence and uniqueness theorem in terms of these functions. On any Lorentz surface with parallel normalized mean curvature vector field we introduce special geometric (canonical) parameters and prove that any such surface is determined up to a rigid motion by three invariant functions satisfying three natural partial differential equations. In this way we minimize the number of functions and the number of partial differential equations determining the surface, which solves the Lund-Regge problem for this class of surfaces.

• 산업경영시스템학회지
• /
• 제37권4호
• /
• pp.154-161
• /
• 2014

In this research we investigate motion controller performance for mobile robots according to changes in the control loop sampling time. As a result, we suggest a proper range of the sample time, which can minimize final posture errors while improving tracking capability of the controller. For controller implementation into real mobile robots, we use a smooth and continuous motion controller, which can respect robot's path curvature limitation. We examine motion control performance in experimental tests while changing the control loop sampling time. Toward this goal, we compare and analyze experimental results using two different mobile robot platforms; one with real-time control and powerful hardware capability and the other with non-real-time control and limited hardware capability.