• 한국정보전자통신기술학회논문지
• /
• 제16권6호
• /
• pp.509-518
• /
• 2023

본 논문에서는 아날로그 회로 트리밍과 Calibration 등에 필요한 4Kb Poly-Fuse OTP IP를 설계하였다. NMOS Select 트랜지스터와 Poly-Fuse 링크로 구성된 Poly-Fuse OTP 셀의 BL 저항을 줄이기 위해 BL은 Metal 2와 Metal 3를 stack하였다. 그리고 BL 라우팅 저항을 줄이기 위해 4Kb 셀은 64행 × 32열 Sub-block 셀 어레이 2개로 나뉘었으며, BL 구동회로는 Top과 Bottom으로 나누어진 2Kb Sub-block 셀 어레이의 가운데에 위치하고 있다. 한편 본 논문에서는 1 Select 트랜지스터에 1 Poly-Fuse 링크를 사용하는 OTP 셀에 맞게 코어회로를 제안하였다. 그리고 OTP IP 개발 초기 단계에서 프로그램되지 않은 Poly-Fuse의 저항이 5kΩ까지 나올수 있는 경우까지를 고려한 데이터 센싱 회로를 제안하였다. 또한 Read 모드에서 프로그램되지 않은 Poly-Fuse 링크를 통해 흐르는 전류를 138㎂ 이하로 제한하였다. DB HiTek 90nm CMOS 공정으로 설계된 Poly-Fuse OTP 셀 사이즈는 11.43㎛ × 2.88㎛ (=32.9184㎛2)이고, 4Kb Poly-Fuse OTP IP 사이즈는 432.442㎛ × 524.6㎛ (=0.227mm²)이다.

• 대한전자공학회논문지SD
• /
• 제48권2호
• /
• pp.20-27
• /
• 2011

모바일 기기에 장착되는 CMOS 이미지 센서(CIS) 칩은 배터리 용량의 한계로 인해 저전력 소모를 요구한다. 본 논문에서는 전력소모를 줄일 수 있는 데이터 플립플롭 회로와 새로운 저전력 구조의 Single-Slope A/D Converter(SS-ADC)를 사용한 이미지 센서를 설계하여 모바일 기기에 사용되는 CIS 칩의 전력 소모를 감소시켰다. 제안하는 CIS는 $2.25um{\times}2.25um$ 면적을 갖는 4-Tr Active Pixel Sensor 구조를 사용하여 QVGA($320{\times}240$)급 해상도를 갖도록 설계되었으며 0.13um CMOS 공정에서 설계되었다. 실험 결과, CIS 칩 내부의 SS-ADC 는 10-b 해상도를 가지며, 동작속도는 16 frame/s 를 만족하였고, 전원 전압 3.3V(아날로그)/1.8V(Digital)에서 25mW의 전력 소모를 보였다. 측정결과로부터 제안된 CIS 칩은 기존 CIS 칩에 비해 대기시간동안 약 22%, 동작시간동안 약 20%의 전력이 감소되었다.

• 한국정보통신학회논문지
• /
• 제13권7호
• /
• pp.1371-1378
• /
• 2009

본 논문에서는 로직 공정 기반의 저전력 eFuse OTP 메모리 셀을 제안하였다. eFuse OTP 메모리 셀은 프로그램과 읽기 모드에 최적화되도록 각각의 트랜지스터를 사용하였으며, WL과 BL의 기생적인 커패시턴스를 줄이므로 읽기 모드에서의 동작 전류를 줄였다. 그리고 저전력, 저면적의 eFuse OTP 메모리 IP 설계를 위하여 비동기식 인터페이스, 분리된 I/O, 디지털 센싱 방식의 BL 감지 증폭기 회로를 사용하였다. 모의실험 결과 읽기 모드에서의 동작전류는 VDD, VIO 각각 349.5${\mu}$A, 3.3${\mu}$A로 나왔다. 그리고 동부하이텍 0.18${\mu}$m generic 공정으로 설계된 eFuse OTP 메모 리 IP의 레이아웃 면적은300 ${\times}$557${\mu}m^2$이다.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2004년도 하계종합학술대회 논문집(2)
• /
• pp.549-552
• /
• 2004

The thesis describes the design of 12bit digital-to-analog converter (DAC) which shows the conversion rate of 500MHz and the power supply of 3.3V with 0.35${\mu}m$ CMOS 1-poly 4-metal process for advanced wireless transceiver of high speed and high resolution. The proposed DAC employes segmented structure which consists of 6bit MSB, 3bit mSB, 3bit LSB for area efficiency Also, using a optimized aspect ratio of process and new triple diagonal symmetric centroid sequence for high yield and high linearity. The proposed 12bit current mode DAC was employs new deglitch circuit for the decrement of the glitch energy. Simulation results show the conversion rate of 500MHz, and the power dissipation of 85mW at single 3.3V supply voltage. Both DNL and INL are found to be smaller than ${\pm}0.65LSB/{\pm}0.8LSB$.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2003년도 춘계전력전자학술대회 논문집(1)
• /
• pp.227-230
• /
• 2003

In this paper, a full bridge edge-resonant zero voltage mode based soft-switching PWM DC-DC power converter with a high frequency center tapped transformer link stage is presented from a practical point of view. The power MOSFETS operating as synchronous rectifier devices are implemented in the rectifier center tapped stage to reduce conduction power losses and also to extend the transformer primary side power MOSFETS ZVS commutation area from the rated to zero-load without a requirement of a magnetizing current. The steady-state operation of this phase-shift PWM controlled power converter is described in comparison with a conventional ZVS phase-shift PWM DC-DC converter using the diodes rectifier. Moreover, the experimental results of the switching power losses analysis are evaluated and discussed in this paper. The practical effectiveness of the ZVS phase-shift PWM DC-DC power converter treated here is actually proved by using 2.5kW-32kHz breadboard circuit. An actual efficiency of this converter is estimated in experiment and is achieved as 97$\%$ at maximum.

• 조명전기설비학회논문지
• /
• 제22권7호
• /
• pp.7-15
• /
• 2008

A single active capacitor snubber-assisted soft-switching sinewave pulse modulation utility-interactive power conditioner with a three-winding flyback high frequency transformer link and a bidirectional active power switch in its secondary side has been proposed. With the aid of the switched-capacitor quasi-resonant snubber cell, the high frequency switching devices in the primary side of the proposed DC-to-AC sinewave power inverter can be turned-off with ZVS commutation. In addition to this, the proposed power conditioner in the DCM can effectively take the advantages of ZCS turn-on commutation. Its output port is connected directly to the utility AC power source grid. At the end, the prototype of the proposed HF-UPC is built and tested in experiment. Its power conversion conditioning and processing circuit with a high frequency flyback transformer link is verified and the output sinewave current is qualified in accordance with the power quality guidelines of the utility AC interactive power systems.

• 조명전기설비학회논문지
• /
• 제28권8호
• /
• pp.75-81
• /
• 2014

It has been widely accepted that open phase may separate one of the power lines from power supply which is mainly caused by fuse melting, malfunction for source circuit breaker, contact failure, and disconnection under normal operating conditions, and is considered a kind of failure mode during disconnection of neutral wires as well. When open phase occurs, unequal voltage between phase might happen in the unbalanced load connected each phase, and further, depending on conditions of load, malfunction by providing low voltage. Moreover, load could be burned or overheated with overvoltage, which, in turn, can be a contributor to starting fires. Accordingly, in order to clearly overcome these problems, the current study aims to introduce the theory of uninterruptible power open phase compensation device, meaning that unbalanced power automatically restores balanced power and provides continuously the power supply without blackout, and verify it through simulation and experiments.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2010년도 하계학술대회 논문집
• /
• pp.15-16
• /
• 2010

This paper is study on a high efficiency DC-DC converter of discontinuous conduction mode (DCM) added electric isolation. The converters of high efficiency are generally made that the power losses of the used semiconductor switching devices is minimized. To achieve high efficiency system, the proposed converter is constructed by using a quasi resonant circuit. The control switches using in the converter are operated with soft switching by quasi resonant method. The control switches are operated without increasing their voltage and current stresses by the soft switching technology. The result is that the switching loss is very low and the efficiency of the system is high. The proposed converter is also added electric isolation which is used a pulse transformer. When the power conversion system is required electric isolation, the proposed converter is adopted with the converter system development of high efficiency. The soft switching operation and the system efficiency of the proposed converter are verified by digital simulation and experimental results.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2012년도 추계학술대회 논문집
• /
• pp.344-349
• /
• 2012

This paper presents a new small-sized damper featuring magneto-rheological (MR) fluid which can be applied to vibration control system. The proposed MR damper consists of cylinder, piston, a couple of bearings, oil-seals and magnetic circuit which has two coils. In this damper, approximately 5cc of MR fluid is used. The damping force of the MR damper is designed to be followed by linear shear-mode Bingham-plastic model. In order to verify the performance of the MR damper, an experimental apparatus is established. In the experimental test, the damping force of the MR damper is measured with respect to time, displacement and velocity. In addition, the time response of MR damper is measured when 1A of step current is applied. Finally, The proposed small MR damper is applied to vibration control. In this process, a simple 1-DOF system is modeled and controlled using PID controller.

• 한국소음진동공학회논문집
• /
• 제22권11호
• /
• pp.1121-1127
• /
• 2012

This paper presents a new small-sized damper featuring magneto-rheological(MR) fluid which can be applied to vibration control system. The proposed MR damper consists of cylinder, piston, a couple of bearings, oil-seals and magnetic circuit which has two coils. In this damper, approximately 5cc of MR fluid is used. The damping force of the MR damper is designed to be followed by linear shear-mode Bingham-plastic model. In order to verify the performance of the MR damper, an experimental apparatus is established. In the experimental test, the damping force of the MR damper is measured with respect to time, displacement and velocity. In addition, the time response of MR damper is measured when 1A of step current is applied. Finally, the proposed small MR damper is applied to vibration control. In this process, a simple 1-DOF system is modeled and controlled using PID controller.