• Journal of Power Electronics
• /
• v.19 no.1
• /
• pp.108-118
• /
• 2019

This paper proposes a DC-link voltage balance controller using the fourth-phase of a three-level neutral-point clamped (NPC) PWM converter with medium vector selection (MVS) PWM for common-mode voltage reduction. MVS PWM makes the voltage reference by synthesizing the voltage vectors that cannot generate common-mode voltage. This PWM method is effective for reducing the EMI noise emitted from converter systems. However, the DC-link voltage imbalance problem is caused by the use of limited voltage vectors. Therefore, in this paper, the effect of MVS PWM on the DC-link voltage of a three-level NPC converter is analyzed. Then a proportional-derivative (PD) controller for the DC-link voltage balance is designed from the DC-link modeling. In addition, feedforward compensation of the neutral point current is included in the proposed PD controller. The effectiveness of the proposed controller is verified by experimental results.

• Progress in Superconductivity and Cryogenics
• /
• v.11 no.3
• /
• pp.20-25
• /
• 2009

The quench detection system of the KSTAR (Korea Superconducting Tokamak Advanced Research) primarily uses the resistive voltage measurement due to a quench. This method is to detect the resistive voltage generated by a quench, which is continuously maintained above the preset voltage threshold for a given holding time. As the KSTAR PF (Poloidal Field) coils are operated in the pulse current mode, the large inductive voltages are generated. Therefore the voltage threshold and the quench holding time should be determined by considering both the inductive voltages measured during the operation, and the maximum conductor temperature rise through the quench analysis. In this paper, the compensation methods for minimizing the inductive voltages are presented for the KSTAR PF coils. The quench hot spot analysis of the PF coils was carried out by the analytical and numerical methods for determining the proper values of the quench voltage threshold and the allowable quench protection delay time.

• Journal of Electrical Engineering and Technology
• /
• v.10 no.1
• /
• pp.379-387
• /
• 2015

A custom power device provides an integrated solution to the present problems that are faced by the utilities and power distribution. In this paper, a new controller is designed which is connected to a multiconverter unified power quality conditioner (MC-UPQC) for improving the power quality issues adopted modified synchronous reference frame (MSRF) theory with Fuzzy logic control (FLC) technique. This newly designed controller is connected to a source in order to compensate voltage and current in two feeders. The expanded concept of UPQC is multi converter-UPQC; this system has a two-series voltage source inverter and one shunt voltage source inverter connected back to back. This configuration will helps mitigate any type of voltage / current fluctuations and power factor correction in power distribution network to improve power quality issues. In the proposed system the power can be conveyed from one feeder to another in order to mitigate the voltage sag, swell, interruption and transient response of the system. The control strategies of multi converter- UPQC are designed based on the modified synchronous reference frame theory with fuzzy logic controller. The fast dynamics response of dc link capacitor is achieved with the help of Fuzzy logic controller. Different types of fault conditions are taken and simulated for the analysis and the results are compared with the conventional method. The relevant simulation and compensation performance analysis of the proposed multi converter-UPQC with fuzzy logic controller is performed.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.11 no.1
• /
• pp.7-13
• /
• 2006

Linear compressors with a free piston driven by a linear motor are widely attention in the cooling apparatus such as refrigerator due to the high efficiency The stroke of piston in the linear compressor driven by LPMSM (Linear Permanent-Magnet Synchronous Motor) can be obtained from Integrating the input voltage and current of LPMSM, but it may be diverged due to dc components in the voltage and current. The strategy to prevent the divergence of stroke using both the high-pass filter and do offset compensation was suggested. The equations for the magnitude and phase of the stroke and also dc offset including the stroke are derived as a function of the cut-off frequency of HPF. The accurate stroke of a piston can be calculated by compensating for dc offset. The performance of the newly developed stroke calculation scheme has been verified by experimentally on a linear compressor drive system, where the control was implemented by a 16-bit DSP.

• Journal of Power Electronics
• /
• v.14 no.6
• /
• pp.1303-1313
• /
• 2014

Dynamic behavior of the harmonic detection part of an active power filter (APF) has an essential role in filter compensation performances during transient conditions. Instantaneous power (p-q) theory is extensively used to design harmonic detectors for active filters. Large overshoot of p-q theory method deteriorates filter response at a large and rapid load change. In this study the harmonic estimation of an APF during transient conditions for balanced three-phase nonlinear loads is conducted. A novel fuzzy instantaneous power (FIP) theory is proposed to improve conventional p-q theory dynamic performances during transient conditions to adapt automatically to any random and rapid nonlinear load change. Adding fuzzy rules in p-q theory improves the decomposition of the alternating current components of active and reactive power signals and develops correct reference during rapid and random current variation. Modifying p-q theory internal high-pass filter performance using fuzzy rules without any drawback is a prospect. In the simulated system using MATLAB/SIMULINK, the shunt active filter is connected to a rapidly time-varying nonlinear load. The harmonic detection parts of the shunt active filter are developed for FIP theory-based and p-q theory-based algorithms. The harmonic detector hardware is also developed using the TMS320F28335 digital signal processor and connected to a laboratory nonlinear load. The software is developed for FIP theory-based and p-q theory-based algorithms. The simulation and experimental tests results verify the ability of the new technique in harmonic detection of rapid changing nonlinear loads.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.15 no.2
• /
• pp.273-284
• /
• 2020

This paper proposes a method of designing and controlling delta robots with low-cost DC motors, which are widely used in the automation process. Simulation was performed by interpreting the mechanics and dynamics of the delta robot, and based on this analysis, low-cost DC motor was selected. Experiments were conducted to obtain characteristic values of motors and the current-position cascade control system was designed and implemented. In order to verify the feasibility of the proposed system, the experiment to check that the end-effector of the delta robot follows the target path was progressed. Through the experiment, the limitations of using low-cost motors were overcome by designing compensation algorithms and the performance of the position control was verified.

• Journal of the Korean Society of Industry Convergence
• /
• v.23 no.2_1
• /
• pp.115-124
• /
• 2020

In wireless power transfer (WPT) system, the conventional compensation topologies only can provide a constant current (CC) or constant voltage (CV) output under their resonant conditions. It is difficult to meet the CC and CV hybrid charging requirements without any other schemes. In this study, a switching hybrid topology (SHT) is proposed for CC and CV electric vehicle (EV) battery charging. By utilizing an additional capacitor and two AC switches (ACSs), a double-side LCC (DS-LCC) and an inductor and double capacitors-series (LCC-S) topologies are combined. According to the specified CC and CV charging profile, the CC and CV charging modes can be flexibly converted by the two additional ACSs. In addition, zero phase angle (ZPA) also can be achieved in both charging modes. In this method, because the operating frequency is fixed, without using PWM control, and only a small number of devices are added, it has the benefits of low-cost, easy-controllability and high efficiency. A 3.3-kW experimental prototype is configured to verify the proposed switching hybrid charger. The maximum DC efficiencies (at 3.3-kW) of the proposed SHT is 92.58%.

• Journal of Broadcast Engineering
• /
• v.2 no.2
• /
• pp.114-124
• /
• 1997

In object based coding, binary shape ccx:ling plays an important role by ccx:ling the outer shape of object. Here we propose a new shape ccx:ling tool, which enccx:les the outline of shape from a baseline. Different from 2-D (Vertex) shape ccx:ling algorithms. the proposed method encodeds the data that are extracted in a I-D fashion. The enccx:led data consist of the starting position, distance lists, and turning point lists. In the lossless ccx:ling mode, every contour pixel is input for ccx:ling, whereas variable sampling has been employed to enccx:le fewer contour pixels while preserving reasonable distortion. For interframe ccx:ling, a fast motion compensation was achieved by use of distance and turning point lists. Subjective viewing tests proved that the proposed method outperforms the current shape ccx:ling standard, CAE, in MPEG-4. In objective results for compression efficiency, the proposed method was significantly better in intraframe coding than CAE, whereas CAE was better in interframe ccx:ling.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.16 no.5
• /
• pp.83-89
• /
• 2002

The purpose of this paper is to assess experimentally system stability of the 154［㎸］transmission system due to the current of the forthcoming AC High-Speed Railway (HSR) era. It introduces a simple method to evaluate the system stability. The proposed method also shows the relationship between stability and power losses, and the stability indices made by the numerical process proposed in this paper will be used to assess whether a system can be stabilized or not. This paper also presents the improvement of the stability via loss reduction using a shunt compensator. Reactive power compensation is often the most effective way to improve both power transfer capability and system stability. The suitable modeling of the traction power system should be applicable to the PSS/E. The proposed method is tested on a practical system which will be expected to accommodate the heavy HSR load.

• Journal of the Korea Computer Industry Society
• /
• v.3 no.7
• /
• pp.927-936
• /
• 2002

This paper presents the extraction of a feature by motion vector for efficient content-based retrieval for digital video. in this paper, divided by general size block for the current frame by video, using BMA(block matching algorithm) for an estimate by block move based on a time frame. but in case BMA appeared on a different pattern fact of motion in the vector obtain for the BMA. solve in this a problem to application for full search method this method is detected by of on many calculations. I propose an alternative plan in this paper Limit the search region to $\pm$15 and search is a limit integer pixel. a result, in this paper is make an estimate motion vector in more accurately using motion vector in adjoin in blocks. however, refer to the block vector because occurrence synchronism. Such addition information is get hold burden receive to transmit therefore, forecasted that motion feature each block and consider for problems for establish search region. in this paper Algorithm based to an examination Motion Estimation method by for motion Compensation is proposed.