• The Journal of Korean Academy of Prosthodontics
• /
• v.42 no.2
• /
• pp.167-174
• /
• 2004

Statement of problem: Removable partial denture and complete denture often require denture base relines to improve the fit against the tissue-bearing mucosa because of gradual changes in edentulous ridge contours and resorption of underlying bone structure. Purpose: This study was performed to investigate the effect of surface design on bond strength of relining denture base resins to denture base acrylic resin. Materials and method: Heat curing resin(Lucitone 199, Dentsply U.S.A. and Vertex, Dentimex, Holland), self curing resin(Tokuso rebase, Tokuyama, Japan), and visible light curing resin(Triad, Dentsply, U.S.A.) were used in this study. The surface designs were classified as butt, bevel and rabbet joint and the bond strengths were measured by Universial Testing Machine (Zwick 2020, Zwick Co., Germany). Results and Conclusion: The obtained results from this study were as follows ; 1. The bond strength of Vertex resin was higher than those of Tokuso rebase and Triad. 2. The bond strength of rabbet and bevel joint was higher than that of butt joint. 3. The failure mode of Triad and Tokuso rebase was mainly adhesive, but cohesive failure was shown mainly in vertex.

• Polymer(Korea)
• /
• v.24 no.2
• /
• pp.220-227
• /
• 2000

Silica and carbon black filled natural rubber (NR) vulcanizates were prepared with different mixing modes and amounts of fillers. Curing characteristics, morphology. and tear properties of the NR vulcanizates were investigated. The NR vulcanizates filled with silica and carbon black sequentially showed longer induction time ($t_2$), cure index ($t_{90}$ ), and lower maximum torque ($T_{max}$ ) than the NR vulcanizates filled with them simultaneously, during curing process. The former showed superior dispersion of fillers and tear properties to the latter. The NR vulcanizates containing 30 phr of silica showed excellent properties in the experimental range.

• Geomechanics and Engineering
• /
• v.29 no.1
• /
• pp.13-23
• /
• 2022

Peat soil has the characteristics of high moisture content, large void ratio and low shear strength. In this study, unconfined compressive strength and SEM tests are conducted to investigate the effects of ultrahigh moisture content, cement content, organic content and pH value on the strength of solidified peat. As an increase in the cement content and curing period, the failure mode of solidified peat soil changes from ductile failure to brittle failure. The influence of moisture content on the strength of solidified peat is greater than the cement content. As cement content increases from 10% to 30%, strength of solidified peat at a curing age of 28 days increases by 161%~485%. By increasing water content by 100%, decreases of solidified peat at a curing age of 28 days is 42%~79%. Compared with the strength of solidified peat with a pH value of 5.5, the strength of peat with a pH value of 3.5 reduces by 10% ~ 46%, while the strength of peat with a pH value of 7.0 increases by 8% ~ 38%. It is recommended to use filler materials for stabilizing peat soil with moisture content greater than 200%. Because of small size of clay particles, clay added in the cement solidified peat can improve much higher strength that that of sand.

• Proceedings of the KIEE Conference
• /
• 1995.07c
• /
• pp.1171-1173
• /
• 1995

Polyimide thin films were fabricated through the vapor deposition polymerization method, and the structure and capacitance characteristics of them were investigated in detail. It was found that the chemical structure and uniformity of the film could be stabilized with curing. The peaks of $720cm^{-l},\;1380cm^{-1}\;and\;1780cm^{-1}$ show C=O stretch mode, C-N stretch mode and carbonyl stretch mode, and those of polyimide which cured over $300^{\circ}C$ were fixed. It was found that capacitance was changed in proportion to temperature.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2000.11a
• /
• pp.84-87
• /
• 2000

Square tubes used for vehicle structure components have an important role on keeping its stiffness and preserving occupant safety in vehicle collision and rollover in which it experience axial collapse, bending collapse or both. Bending collapse, which absorbs kinetic energy of the impact and retains a survival space for the occupant, is a dominant failure mode in oblique collision and rollover. Thus, in this paper, the bending collapse characteristics such as the maximum bending moment and energy absorption capacity of the square tube replaced by light-weight material were evaluated and presented. The bending test of cantilever tubes which were fabricated with aluminum, GFRP and aluminum/ GFRP hybrid by co-curing process was performed. Then the maximum bending moment and the energy absorption capacity from the moment-angle curve were evaluated. Based on the test results, it was found that aluminum/ GFRP hybrid tube can show better specific energy absorption capacity compared to the pure aluminum or GFRP tube and can convert unstable collapse mode which may occur in pure GFRP tube to stable collapse mode like a aluminum tube in which plastic hinge is developed.

• Restorative Dentistry and Endodontics
• /
• v.32 no.1
• /
• pp.28-36
• /
• 2007

The purpose of this study was to compare the effect of exponential curing method with conventional curing and soft start curing method on polymerization shrinkage of composite resins. Three brands of composite resins (Synergy Duo Shade, Z250, Filtek Supreme) and three brands of light curing units (Spectrum 800, Elipar Highlight, Elipar Trilight) were used. 40 seconds curing time was given. The shrinkage was measured using linometer for 90 seconds. The effect of time on polymerization shrinkage was analysed by one-way ANOVA and the effect of curing modes and materials on polymerization shrinkage at the time of 90s were analysed by two-way ANOVA. The shrinkage ratios at the time of 20s to 90s were taken and analysed the same way. The results were as follows : 1. All the groups except Supreme shrank almost within 20s Supreme cured by soft start and exponential curing had no further shrinkage after 30s (p < 0.05). 2. Statistical analysis revealed that polymerization shrinkage varied among materials (p = 0.000) and curing modes (p = 0.003). There was no significant interaction between material and curing mode. 3. The groups cured by exponential curing showed the statistically lower polymerization shrinkage at 90s than the groups cured by conventional curing and soft start curing (p < 0.05). 4. The initial shrinkage ratios of soft start and exponential curing were statistically lower than conventional curing (p < 0.05). From this study, the use of low initial light intensities may reduce the polymerization rate and, as a result, reduce the stress of polymerization shrinkage.

• Korean Journal of Materials Research
• /
• v.14 no.5
• /
• pp.322-327
• /
• 2004

Copper-based leadframe sheets were oxidized in two kinds of hot alkaline solutions to form brown-oxide or black-oxide layer on the surface. The oxide coated leadframe sheets were molded with epoxy molding compound (EMC). After post mold curing, the oxide-coated EMC-leadframe joints were machined to form sandwiched Brazil-nut (SBN) specimens. The SBN specimens were used to measure the fracture toughness of the EMC/leadframe interfaces under mixed-mode (mode I + mode II) loading conditions. Fracture surfaces were analyzed by various equipment to investigate failure path. The results revealed that the failure paths were strongly dependent on the oxide type. In case of brown oxide, hackle-type failure was observed and failure path lay near the EMC/CuO interface with a little inclining to CuO at all case. On the other hand, in case of black oxide, quite different failure path was observed with respect to the distance from the tip of pre-crack and phase angle. Different failures occurred with oxide type is presumed to be due to the difference in microstructure of the oxides.

• Proceedings of the KIEE Conference
• /
• 1993.07b
• /
• pp.1162-1164
• /
• 1993

The Thermally Stimulated Current(TSC) spectroscopy has been applied to study the influence of the structual cahange and interface on the electrical properties of epoxy composites. Three DGEBA-MeTHPA matrix model samples mixed different ratios and silica($SiO_2$) filled sample and silaln treating-filled sample has been studied. Above room temperature, the relaxation mode $\alpha$ peak associated with Tg has been located at $110^{\circ}C$. Below glass transition temperature(Tg), three relaxation modes are observed in all samples: a $\beta$ mode situated at $10^{\circ}C$, a $\gamma$ mode located at $-40^{\circ}C$ and a $\delta$ mode appeared in $-120^{\circ}C$. The analysis of its fine structure indicates that constitution of elementary processes is characterized by the activation energy and relaxation time. Also the dielectric relaxation properties have been investigated to compare the the change of the molecular structure and motion to the relaxation properties and conduction mechanism in TSC spectra.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.28 no.3
• /
• pp.471-479
• /
• 2001

The purpose of this study was to compare the effect of the high intensity halogen light $(850\sim1000mW/cm^2)$ with that of the conventional halogen light $(400mW/cm^2)$ on the hardness of composite resin. Three resin composites (Z-100, 3M, U.S.A. : Tetric Ceram, Vivadent, Liechtenstein; SureFil, Dentsply, U.S.A.) were filed in the stainless steel moulds which were 4mm in diameter and 2, 3, 4, and 5mm in depth, respectively. They were cured under the four different modes : (1) conventional mode, 40 seconds at $400mW/cm^2$; (2) 'ramp' mode, 10 seconds at 100 to $1000mW/cm^2$ plus 10 seconds at $1000mW/cm^2$; (3) 'boost' mode, 10 seconds at $1000mW/cm^2$; and (4) 'standard' mode, 20 seconds at $850mW/cm^2$. The surface hardnesses of the top and the bottom of the resin samples were measured with a microhardness tester (MXT70, Matsuzawa, Japan). The top surface hardness was not significantly different among the curing modes. The bottom surface hardness was generally the highest in the conventional mode and the lowest in the high intensity boost mode. There was no significant difference in the bottom surface hardness between the conventional mode and the high intensity standard mode in 2mm depth. The results suggest that the curing time of the high intensity halogen light $(850mW/cm^2)$ should be at least 20 seconds to produce the equal level of the bottom surface hardness of 2mm resin composite as compared to the hardness produced by the conventional halogen light $(400mW/cm^2)$.

• Korean Journal of Materials Research
• /
• v.15 no.1
• /
• pp.1-5
• /
• 2005

Copper-based leadframe sheets were immersed in two kinds of hot alkaline solutions to form brown-oxide or black-oxide layer on the surface. The oxide-coated leadframe sheets were molded with epoxy molding compound (EMC). After post mold curing, the oxide-coated EMC-leadframe joints were machined to form sandwiched double-cantilever beam (SDCB) specimens. The SDCB specimens were used to measure the fracture toughness of the EMC/leadframe interfaces under quasi-Mode I loading conditions. Fracture surfaces were analyzed by various equipment to investigate failure path. The present paper deals with the failure path, and the cause of the failure path formation with an adhesion model will be treated in the succeeding paper.