• Progress in Superconductivity
• /
• v.1 no.1
• /
• pp.51-55
• /
• 1999

A Ni/Ag/Stainless steel 310S(SS310S) multi-layer sheet has been fabricated by a combination of vacuum brazing, cold rolling and texture annealing processes. After heat-treating the thin Ni/Ag/SS310S multi-layer sheet at $900^{\circ}C$ for 2h, development of (100)<001>cube texture on Ni surface was revealed by (111) pole figure. Quantitative chemical analysis was made by EPMA for the cross-section of the Ni/Ag/SS310S multi-layer sheet. EPMA results showed that Ag diffusion into the Ni layer, which may suppress the cube texture development, was negligible. A small amount of Cr atoms were detected in the Ni layer. It showed that Ag can be used as a chemical barrier of alloying element atoms in Ni layer for the Ni/Ag/SS310S multi-layer sheet and a strong cube texture was developed for the Ni layer in the Ni/Ag/SS310S multi-layer sheet.

• Transactions of Materials Processing
• /
• v.7 no.5
• /
• pp.459-464
• /
• 1998

Effect of the several initial textures such as random texture, rolling texture and cube texture, on the plane strain stretching was studied by interpretation of the finite element method. The calculation of yield locus indicated that the sheet oriented in the cube texture exhibits easy yielding on uniaxial stress state whereas the sheet having either a random or the rolling texture exhibits easy yielding on shear deformation. Upon stretching tests, the thickness strain at the center region contacting the punch was identical regardless of the initial textures while the dependence of the thickness strain on the initial texture was found in the other regions. In general punch loads required or the sheet with an initial cube texture was as expected from calculated yield locus, lower than those for the others.

• Korean Journal of Metals and Materials
• /
• v.47 no.6
• /
• pp.356-362
• /
• 2009

In order to vary the primary recrystallization textures, AA 1050 sheets were cold rolled in two different manners. Differences in cold rolling schedule gave rise to the formation of different cold rolling textures also leading to the formation of different primary recrystallization textures. Upon annealing for grain growth, changes in microstructure and texture hardly occurred in the sample depicting Cube recrystallization texture, while grain growth was accompanied with the development {001}<100> Cube texture in the sample displaying a recrystallization texture comprising of weak rolling texture components. The selective growth of Cube oriented grains is attributed to the high mobility of their grain boundaries.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1997.03a
• /
• pp.233-239
• /
• 1997

The effect of the cross-rolling on the evolution of the deformation texture and the subsequent annealing texture was studied in 5182 aluminium alloy. The orientation density near {011}<110>. The weak ${\beta}$-fiber orientations in the deformation texture lead to the randomization of the annealing texture, whereas the strong ${\beta}$-fiber orientations lead to the strong Cube orientation in the annealing texture. The development of the strong rotated Cube orientation in the annealing texture seemed to be related with the decrease in the R-value.

• Progress in Superconductivity
• /
• v.7 no.2
• /
• pp.145-151
• /
• 2006

Nickel and nickel-tungsten alloy were electroplated on a cold rolled and heat treated copper(Cu) substrate. 4 mm-thick high purity commercial grade Cu was rolled to various thicknesses of 50, 70, 100 and 150 micron. High reduction ratio of 30% was applied down to 150 micron. Rolled texture was converted into cube texture via high temperature heat treatment at $400-800^{\circ}C$. Grain size of Cu was about 50 micron which is much smaller compared to >300 micron for the Cu prepared using smaller reduction pass of 5%. 1.5 km-long 150 micron Cu was fabricated with a rolling speed of 33 m/min and texture of Cu was uniform along length. Abnormal grain growth and non-cube texture appeared for the specimen anneal above $900^{\circ}C$. 1-10 micron thick Ni and Ni-W film was electroplated onto an annealed cube-textured Cu or directly on a cold rolled Cu. Both specimens were annealed and the degree of texture was measured. For electroplating of Ni on annealed Cu, Ni layer duplicated the cube-texture of Cu substrate and the FWHM of in plane XRD measurement for annealed Cu layer and electroplated layer was $9.9^{\circ}\;and\;13.4^{\irc}$, respectively. But the FWHM of in plane XRD measurement of the specimen which electroplated Ni directly on cold rolled Cu was $8.6^{\circ}$, which is better texture than that of nickel electroplated on annealed Cu and it might be caused by the suppression of secondary recrystallization and abnormal grain growth of Cu at high temperature above $900^{\circ}C$ by electroplated nickel.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09b
• /
• pp.1249-1250
• /
• 2006

Cube textured Ni substrate were fabricated for YBCO coated conductors from the initial specimens prepared by powder metallurgy (P/M) and casting and the effects of annealing temperature and reduction ratio on texture formation and microstructural evolution were evaluated. The initial specimens were rolled and then annealed in the temperature at $600^{\circ}C{\sim}1200^{\circ}C$. A strong cube texture formed for P/M substrate, and the degree of texture did not significantly vary with annealing temperature of $600^{\circ}C{\sim}1100^{\circ}C$. On the other hand, the texture of casting substrate was more dependent on the annealing temperature and twin texture and several minor texture components started to form at $1000^{\circ}C$.

• Progress in Superconductivity
• /
• v.1 no.1
• /
• pp.47-50
• /
• 1999

An Ag/Ni bi-layer sheet was fabricated by the combination of powder metallurgy, diffusion bonding, cold rolling and texture annealing processes. After heat treating the cold rolled thin Ag/Ni bi-layer sheet at $900^{\circ}C$ for 4h, the excellent cube texture was developed on nickel surface. Qualitative chemical analysis using EPMA showed that inter diffusions of Ni and Ag in Ag/Ni bi-layer composite were negligible. It showed that Ag can be used as a chemical barrier for Ni and vice versa.

• Progress in Superconductivity
• /
• v.6 no.1
• /
• pp.64-68
• /
• 2004

We fabricated cube-textured Ni and Ni-W alloy substrates for coated conductors and characterized the effects of W addition on microstructure, mechanical strength, and magnetic properties of the substrate. Pure Ni and Ni-(2, 3, 5at.%)W alloys were prepared by plasma arc melting, heavily cold rolled and then annealed at various temperatures of $600-1300^{\circ}C$. The texture was evaluated by pole-figure and orientation distribution function (ODF) analysis. Mechanical properties were investigated by micro Vickers hardness and tension test. Ferromagnetism of the substrate was measured by physical property measurement system (PPMS). It was observed that Ni-W substrates had sharp cube texture, and the full-width at half-maximums (FWHMs) of in-plane texture was $^{\circ}$-5.57$4.42^{\circ}$, which is better than that of pure Ni substrate. In addition cube texture of Ni-W substrates was retained at higher temperature up to $1300^{\circ}C$. Microstructural observation showed that the Ni-W substrates had fine grain size and higher mechanical properties than the pure Ni substrate. These improvements are probably due to strengthening mechanisms such as solid solution hardening and/or grain size strengthening. PPMS analysis showed that addition of W effectively reduced saturation magnetization in applied magnetic field and Curie temperature.

• Progress in Superconductivity
• /
• v.1 no.2
• /
• pp.120-124
• /
• 2000

Ni-13%Cr and Ni-70%Cu alloy tapes were prepared by using high purity metal powders as starting materials. The Ni-13%Cr and the Ni-70%Cu mixtures were isostatically pressed, sintered, rolled and texture-annealed. SEM EDS analysis showed that copper and nickel atoms were completely mixed, while the alloying between the chromium powders and the nickel powders was incomplete. In spite of incomplete alloying between nickel and chromium powders, sharp cube-texture was developed for the Ni-13%Cr tape as well as the Ni-70%Cu tape.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.07a
• /
• pp.535-538
• /
• 2002

Cube-textured Ni substrates for YBCO coated conductors were fabricated by cold-rolling and annealing of Ni powder compacts. To establish the optimum sintering temperature, tensile test was performed for the Ni rod sintered at various temperatures. The Ni rods prepared at above 100$0^{\circ}C$ showed good mechanical properties due to the complete densification of the Ni rods. The Ni rods were rolled to final thickness of 100 ${\mu}{\textrm}{m}$ and then annealed at 100$0^{\circ}C$ for various annealing time for texture development. The texture analysis made by 2 $\theta$ scan and pole-figure showed that the cube texture was developed in a short time of a few munitues. The FWHM of in-plane and out of plane texture of the prepared Ni tapes was 8-10$^{\circ}$. The AEM surface roughness of the Ni tapes was as smooth as 3 nm.