• Korean Journal of Metals and Materials
• /
• v.46 no.9
• /
• pp.585-592
• /
• 2008

Flip-chip bonding using Cu-Sn mushroom bumps composed of Cu pillar and Sn cap was accomplished, and the contact resistance and the thermal cycling reliability of the Cu-Sn mushroom bump joints were compared with those of the Sn planar bump joints. With flip-chip process at a same bonding stress, both the Cu-Sn mushroom bump joints and the Sn planar bump joints exhibited an almost identical average contact resistance. With increasing a bonding stress from 32 MPa to 44MPa, the average contact resistances of the Cu-Sn mushroom bump joints and the Sn planar bump joints became reduced from $30m{\Omega}/bump$ to $25m{\Omega}/bump$ due to heavier plastic deformation of the bumps. The Cu-Sn mushroom bump joints exhibited a superior thermal cycling reliability to that of the Sn planar bump joints at a bonding stress of 32 MPa. While the contact resistance characteristics of the Cu-Sn mushroom bump joints were not deteriorated even after 1000 thermal cycles ranging between $-40^{\circ}C$ and $80^{\circ}C$, the contact resistance of the Sn planar bump joints substantially increased with thermal cycling.

• Proceedings of the KWS Conference
• /
• 2006.05a
• /
• pp.30-32
• /
• 2006

The interfacial reaction and reliability of eutectic Sn-Pb and Pb-free eutectic Sn-Ag ball-grid-array (BGA) solders with an immersion Ag-plated Cu substrate were evaluated following isothermal aging at $150^{\circ}C$. During reflowing, the topmost Ag layer was dissolved completely into the molten solder, leaving the Cu layer exposed to the molten solder for both solder systems. A typical scallop-type Cu-Sn intermetallic compound (IMC) layer was formed at both of the solder/Cu interfaces during reflowing. The thickness of the Cu-Sn IMCs for both solders was found to increase linearly with the square root of isothermal aging time. The growth of the $Cu_3Sn$ layer for the Sn-37Pb solder was faster than that for the Sn-3.5Ag solder, In the case of the Sn-37Pb solder, the formation of the Pb-rich layer on the Cu-Sn IMC layer retarded the growth of the $Cu_6Sn_5$ IMC layer, and thereby increased the growth rate of the $Cu_3Sn$ IMC layer. In the ball shear test conducted on the Sn-37Pb/Ag-plated Cu joint after aging for 500h, fracturing occurred at the solder/$Cu_6Sn_5$ interface. The shear failure was significantly related to the interfacial adhesion strength between the Pb-rich and $Cu_6Sn_5$ IMC layers. On the other hand, all fracturing occurred in the bulk solder for the Sn-3.5Ag/Ag-plated Cu joint, which confirmed its desirable joint reliability.

• Journal of the Microelectronics and Packaging Society
• /
• v.7 no.2
• /
• pp.13-19
• /
• 2000

Shear strengths of BGA solder joints on Cu pads were studied for Cu-containing Sn (0, 1.5, and 2.5 wt.% Cu) and Sn-40Pb (0 and 0.5wt.% Cu) solders, with emphasis on the roles of the Cu-Sn intermetallic layer thickness and the roughness of the interface between the intermetalic layer and solder. The shear strength test was performed for as-soldered solder joints with various soldering reaction times up to 4 min. The addition of Cu to the pure Sn solder results in an enhanced growth of the intermetallic layer whereas the effect of Cu addition to the Sn-40Pb solder is primarily on the reduction of the roughness of the intermetallic/solder interface. The critical thickness of the intermetallic layer for a maximum shear strength depends on the solder materials, which was measured to be ~ 2.3 $\mu\textrm{m}$ for Sn-Cu solders and ~ 1.2 $\mu\textrm{m}$ for Sn-Pb-Cu solders. The shear strength at the critical intermetallic layer thickness seems to increase as the intermetallic/solder interface becomes rougher. This is in accordance with the observation that the sheared fracture occurred initially within the solder tends to shift towards the intermetallic/solder interface as the intermetallic layer grows above the critical thickness.

• Tribology and Lubricants
• /
• v.37 no.3
• /
• pp.83-90
• /
• 2021

In this study, an ultrasonic nanocrystal surface modification (UNSM) was used to improve the mechanical properties, scratch resistance and tribological performance of Cu-based bimetals, which are usually used to manufacture sliding bearings and bushings for internal combustion engines (ICEs). Two different Cu-based bimetals, namely CuPb10Sn10 and CuSn10Bi7, were sintered onto a low carbon steel substrate. The mechanical properties and dry tribological performance using a tensile tester and micro-tribo tester were evaluated, respectively. The scratch resistance was assessed using a micro-scratch tester at an incremental load. The tensile test results showed that the yield strength (YS) and ultimate tensile strength (UTS) of both Cu-based bimetals increased after UNSM. Furthermore, the scratch and tribological tests results revealed that the scratch resistance and tribological performance of both Cu-based bimetals were improved by the application of UNSM. These improvements were mainly attributed to the eliminated pores, increased hardness and reduced roughness after UNSM. CuSn10Bi7 demonstrated better mechanical properties, scratch resistance and tribological performance than CuPb10Sn10. It was found that the presence of Bi in CuSn10Bi7 formed a Cu₁₁Bi₇ intermetallic phase, which is harder than Cu₃Sn. Hence, CuSn10Bi7 demonstrated higher strength and wear resistance than CuPb10Sn10. In addition, a CuSn10Bi7 formed both SnO₂ and Bi₂O₃ that prevented adhesion and improved the tribological performance. It can be expected that under dry tribological conditions, ICEs can utilize UNSM bearings and bushings made of CuSn10Bi7 instead of CuPb10Sn10 under oil-lubricated conditions.

• Proceedings of the International Microelectronics And Packaging Society Conference
• /
• 2003.11a
• /
• pp.76-79
• /
• 2003

본 실험에서는 $S0.7wt\%Cu,\;Sn3.8wt\%Ag0.7wt\%Cu$ solder와 금속층으로서의 좋은 특성을 가지고 있지만 아직 연구 보고 된 적 없는 Pt층과의 리플로 반응에 의해 형성되는 계면금속간화합물의 상 분석을 시도 하였다 또한 솔더내 Cu함량에 따른 계면금속간화합물의 변화에 대하여 연구하기 위해 $Sn1.7wt\%Cu$솔더와 Pt층의 계면반응 현상에 대한 연구도 수행하였다. $Sn0.7(1.7)wt\%Cu$솔더는 순수한 Sn과 Cu를 이용하여 중량비로 제조하였고, $Sn3.8wt\%Ag0.7wt\%Cu$솔더는 솔더페이스트를 사용하였다. 분석은 SEM, EDS, XRD를 이용하였다. 분석 결과 세 가지 무연솔더 모두에서 $PtSn_4$가 계면 금속간화합물로 존재함을 발견하였으며 $1.7wt\%Cu$를 포함한 솔더와 Pt와의 반응에서는 고용도 이상으로 첨가된 Cu에 의해 솔더 내부에 조대한 형상의 $Cu_6Sn_5$가 존재함을 SEM 및 EDS분석을 통하여 발견 하였다.

• Korean Journal of Materials Research
• /
• v.17 no.8
• /
• pp.402-407
• /
• 2007

In electronics manufacturing processes, soldering process has generally been used in surface mounting technology. Because of environmental restriction, lead free solders as like a SnAgCu ternary system are being used widely. After soldering process, the formation and growth of intermetalic compounds(IMCs) are formed in the interface between solder and Cu substrate as follows isothermal temperature and time. In this studies, therefore, we investigated the effects of the Cu substrate thickness on the IMC formation and growth of Sn-40Pb/Cu and Sn-3.0Ag-0.5Cu/Cu solder joints, respectively. The effect of the Cu thickness in PCB Cu pad and pure Cu plate was analyzed as measuring of thickness of each IMC. After solder was soldered on PCB and Cu plate which have different Cu thickness, we measured the IMC thickness in solder joints respectively. Also we compared with the effectiveness of Cu thickness on the IMC growth. From these results, we calculated the activation energy.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.07a
• /
• pp.640-644
• /
• 2000

The microstructure, wettability, shear strength and aging effect of Sn-3.5Ag/Cu and Alloy42 lead-frame solder joints were measured for comparison. In the case of Sn-3.5Ag/Cu, Ag$_3$Sn and Cu$\sub$6/Sn$\sub$5/ phases in the matrix Sn and 1∼2$\mu\textrm{m}$ thick Cu$\sub$6/Sn$\sub$5/ Phase at the interface of solder/lead-frame were formed. In the case of Sn-3.5AAg/A11oy42, only Ag$_3$Sn Phase of low density in the matrix Sn and 0.5∼1.5$\mu\textrm{m}$ thick FeSn$_2$phase at the interface of solder/lead-frame were formed. Comparing to Cu, Alloy42 shear strength of Alloy 42 solder joints was smaller than that of Cu and all declined after aging. After aging at 180$^{\circ}C$ for 1 week, η-Cu$\sub$6/Sn$\sub$5/ layer was formed on Cu lead-frame, while AgSn$_3$ phase in the matrix and thickened FeSn$_2$at the interface were formed on Alloy42 lead-frame.

• Proceedings of the International Microelectronics And Packaging Society Conference
• /
• 2003.11a
• /
• pp.110-113
• /
• 2003

여러가지 Sn-Ag-Cu 솔더조성과 솔더링 후의 냉각속도에 따라 솔더링 접합부에서의 계면 미세조직의 다양한 변화를 관찰해 보았다. 현재까지 Sn-Ag-Cu 3원계 공정점에 대한 정확한 연구가 미흡하고, 상용으로 제품화되고 있는 Sn-Ag-Cu 합금계는 3원계 공정조성에서 약간 벗어난 조성들을 선택하고 있다고 할 수 있다. 따라서, 본 연구에서 사용한 Sn-Ag-Cu 합금 조성은 Sn-3.5Ag, Sn-3Ag-0.7Cu, Sn-3Ag-1.5Cu, Sn-3.7Ag-0.9Cu, Sn-6Ag-0.5Cu로 선택하였으며, 각 조성에서 Lap Shear Joint를 제조하였다. 사용한 Solder pad는 Cu pad와 Cu pad 위에 Au/Ni를 plating한 것을 이용하였다. 리플로우 솔더링 조건은 $250^{\circ}C$ 이상의 온도에서 60초 실시하였으며, 리플로우 솔더링 후의 냉각속도를 달리하여 냉각시켰다. 솔더링 후의 냉각속도가 느려질수록 계면 금속간화합물(IMC)의 두께가 더욱 증가하며, 조대화되었다. 또한 솔더 조성의 영향에서 Cu와 Ag의 함량이 높을수록 계면 IMC의 두께가 증가되었으며, 이는 솔더내부에 형성된 IMC 입자들이 조대화되어 계면 IMC층에 결합되어 나타났기 때문이다.

• Journal of Powder Materials
• /
• v.19 no.4
• /
• pp.317-321
• /
• 2012

In this study, Cu-5Ni-10Sn(wt%) spinodal alloy was manufactured by gas atomization spray forming, and the microstructural features and mechanical properties of Cu-5Ni-10Sn alloy have been investigated during homogenization, cold working and age-hardening. The spray formed Cu-5Ni-10Sn alloy consisted of an equiaxed microstructure with a mixture of solid solution ${\alpha}$-(CuNiSn) grains and lamellar-structure grains. Homogenization at $800^{\circ}C$ and subsequent rapid quenching formed a uniform solid solution ${\alpha}$-(CuNiSn) phase. Direct aging at $350^{\circ}C$ from the homogenized Cu-5Ni-10Sn alloy promoted the precipitation of finely distributed ${\gamma}$' or ${\gamma}-(Cu,Ni)_3Sn$ phase throughout the matrix, resulting in a significant increase in microhardness and tensile strength. Cold working prior to aging was effective in strengthening Cu-5Ni-10Sn alloy, which gave rise to a maximum tensile strength of 1165 MPa. Subsequent aging treatment slightly reduced the tensile strength to 1000-1100 MPa due to annealing effects.

• Journal of the Microelectronics and Packaging Society
• /
• v.15 no.4
• /
• pp.17-24
• /
• 2008

Thermal annealing and electromigration test were performed at $150^{\circ}C$ and $150^{\circ}C,\;5{\times}10^4\;A/cm^2$ conditions, respectively, in order to compare the growth kinetics of intermetallic compound(IMC) in Cu pillar bump. The quantitative interfacial adhesion energy with annealing was measured by using four-point bending strength test in order to assess the effect of IMC growth on the mechanical reliability of Cu pillar bump. Only $Cu_6Sn_5$ was observed in the Cu pillar/Sn interface after reflow. However, $Cu_3Sn$ formed and grew at Cu pillar/$Cu_6Sn_5$ interface with increasing annealing and stressing time. The growth kinetics of total($Cu_6Sn_5+Cu_3Sn$) IMC changed when all Sn phases in Cu pillar bump were exhausted. The complete consumption time of Sn phase in electromigration condition was faster than that in annealing condition. The quantitative interfacial adhesion energy after 24h at $180^{\circ}C$ was $0.28J/m^2$ while it was $3.37J/m^2$ before annealing. Therefore, the growth of IMC seem to strongly affect the mechanical reliability of Cu pillar bump.