• Proceedings of the Materials Research Society of Korea Conference
• /
• 2006.05a
• /
• pp.19.2-19.2
• /
• 2006

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.17 no.6
• /
• pp.91-97
• /
• 2018

Chemical mechanical polishing(CMP) realizes a surface planarity through combined mechanical and chemical means. In CMP process, Preston equation is known as one of the most general approximation of the removal rate. Effects of pressure and relative speed on the mechanical property of Cu CMP has been investigated. On the other hand, The amount of abrasion also increased with changes in pressure and speed, resulting in a proportional increase of temperature during CMP. Especially this temperature is an important factor to change chemical reaction in a Cu CMP. However, when the slurry temperature became higher than $70^{\circ}C$, the removal rate went lower due to abrasives aggregation and scratching occurred on the Cu film. Therefore, it was found that the slurry temperature should not exceed $70^{\circ}C$ during Cu CMP. Finally, authors could increase the pressure, speed and slurry temperature up to a ceratin level to improve the removal rate without surface defects.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.11a
• /
• pp.711-714
• /
• 2004

Chemical mechanical polishing (CMP) has been widely accepted for the global planarization of multi-layer structures in semiconductor manufacturing. However, it still has various problems to the CMP equipment, in particular, among the CMP components, process variables are very important parameters in determining the removal rate and non-uniformity. Using a design of experiment (DOE) approach, this study was performed investigating the interaction between the various parameters such as turntable and head speed, down force and back pressure during CMP. Using statistical analysis techniques, a better understanding of the interaction behavior between the various parameters and the effect on removal rate, no-uniformity and ETC (edge to center) is achieved.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.24 no.1
• /
• pp.17-21
• /
• 2011

Copper (Cu) had been attractive material due to its superior properties comparing to other metals such as aluminum or tungsten and considered as the best metal which can replace them as an interconnect metal in integrated circuits. CMP (Chemical Mechanical Polishing) technology enabled the production of excellent local and global planarization of microelectronic materials, which allow high resolution of photolithography process. Cu CMP is a complex removal process performed by chemical reaction and mechanical abrasion, which can make defects of its own such as a scratch, particle and dishing. The abrasive particles remain on the Cu surface, and become contaminations to make device yield and performance deteriorate. To remove the particle, buffing cleaning method used in post-CMP cleaning and buffing is the one of the most effective physical cleaning process. AE(Acoustic Emission) sensor was used to detect dynamic friction during the buffing process. When polishing is started, the sensor starts to be loaded and produces an electrical charge that is directly proportional to the applied force. Cleaning efficiency of Cu surface were measured by FE-SEM and AFM during the buffing process. The experimental result showed that particles removed with buffing process, it is possible to detect the particle removal efficiency through obtained signal by the AE sensor.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.06a
• /
• pp.82-82
• /
• 2007

The chemical mechanical polishing (CMP) process has been widely used to obtain global planarization of multilevel interconnection process for ultra large scale. integrated circuit applications. Especially, the application of copper CMP has become an integral part of several semiconductor device and materials manufacturers. However, the low-k materials at 65nm and below device structures because of fragile property, requires low down-pressure mechanical polishing for maintaining the structural integrity of under layer during their fabrication. In this paper, we studied electrochemical mechanical polishing (ECMP) as a new planarization technology that uses electrolyte chemistry instead of abrasive slurry for copper CMP process. The current-voltage (I-V) curves were employed we investigated that how this chemical affect the process of voltage induced material removal in ECMP of Copper. This work was supported by grant No. (R01-2006-000-11275-0) from the Basic Research Program of the Korea Science.

• Journal of the Microelectronics and Packaging Society
• /
• v.21 no.4
• /
• pp.117-123
• /
• 2014

Cu through-vias, which can be used as thermal vias or vertical interconnects, were formed using bottom-up electrodeposition filling as well as top-down electrodeposition filling into open via-holes and their microstructures were observed. Solid Cu through-vias without voids could be successfully formed by bottom-up filling as well as top-down filling with direct-current electrodeposition. While chemical-mechanical polishing (CMP) to remove the overplated Cu layer was needed on both top and bottom surfaces of the specimen processed by top-down filling method, the bottomup process has an advantage that such CMP was necessary only on the top surface of the sample.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.07a
• /
• pp.649-650
• /
• 2005

반도체는 고집적화, 고속도화, 저전력화를 목적으로 발전하고 있다. 이를 위하여 design rule의 감소, 새로운 물질과 프로세스의 적용 등 많은 연구가 이루어지고 있으며, RC delay time을 줄이기 위한 Cu 와 저유전율 재료의 적용이 그 대표적인 예라 할 수 있다. Cu 배선은 기존의 Al 배선에 비하여 높은 전자이동 (electro-migration)과 응력 이동 (stress-migration) 저항을 가짐으로써 전기적인 성능 (electrical performance) 에서 이점을 가지고 있다. 반도체에서의 Cu 배선 구조는 평탄화된 표면 및 배선들 사이에서의 좋은 전기적인 절연성을 가져야 하며, 이는 디싱(dishing)과 에로젼(erosion)의 중요한 인자가 된다. 기존의 평탄화 공정인 Cu CMP(Chemical Mechanical Polishing)에 있어서 이러한 디싱, 에로전과 같은 결함은 선결되어져야 할 문제로 인식되고 있다. 따라서 본 연구에서는 이러한 결합들을 감소시키기 위한 새로운 평탄화 방법으로 Cu gap-filling 을 하는 동시에 평탄화된 표면을 이루는 ECMD(Electro-Chemical Mechanical Deposition) 공정의 전기적 기계적 특성을 파악하였다.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.06a
• /
• pp.57-58
• /
• 2006

Chemical-mechanical planarization (CMP) of Cu has used currently in semiconductor process for multilevel metallization system. This process requires the application of a considerable down-pressure to the sample in the polishing, because porous low-k films used in the Cu-multilevel interconnects of 65nm technology node are often damaged by mechanical process. Also, it make possible to reduce scratches and contaminations of wafer. Electrochemical mechanical planarization (ECMP) is an emerging extension of CMP. In this study, the electrochemical mechanical polisher was manufactured. And the static and dynamic potentiodynamic curve of Cu were measured in KOH based electrolyte and then the suitable potential was found.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.11a
• /
• pp.49-49
• /
• 2007

최근 반도체 소자의 고집적화와 나노 (nano) 크기의 회로 선폭으로 인해 기존에 사용되었던 텅스텐이나 알루미늄 금속배선보다, 낮은 전기저항과 높은 electro-migration resistance가 필요한 Cu 금속배선이 주목받게 되었다. 하지만, Cu CMP 공정 시 높은 압력으로 인하여 low-k 유전체막의 손상과 디싱과 에로젼 현상으로 인한 문제점이 발생하게 되었다. 본 논문에서는, $KNO_3$ 전해액의 농도가 Cu 표면에 미치는 영향을 알아보기 위해 Tafel Curve와 CV (cyclic voltammograms)법을 사용하여 전기화학적 특징을 알아보았고 scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), X-ray Diffraction (XRD) 분석을 통해 금속표면을 비교 분석하였다.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.07a
• /
• pp.304-307
• /
• 2003

Replacement of aluminum by copper for interconnections in the semiconductor industry has raised a number of important issues. The integration of copper interconnection can be carried out by CMP(chemical mechanical polishing) is used to planarize the surface topography. In this experiments, we evaluated the optimization of several conditions for chemical additives during Cu CMP process. It was presented that the main cause of grown particle size is tartaric acid. The particle size was in inverse propotion to a quantity of bead and the time of milling process. The slurry stabilizer and oxidizer have been shown to have very good effect by addition in later milling process.