• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2007.06a
• /
• pp.667-668
• /
• 2007

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.11a
• /
• pp.711-714
• /
• 2004

Chemical mechanical polishing (CMP) has been widely accepted for the global planarization of multi-layer structures in semiconductor manufacturing. However, it still has various problems to the CMP equipment, in particular, among the CMP components, process variables are very important parameters in determining the removal rate and non-uniformity. Using a design of experiment (DOE) approach, this study was performed investigating the interaction between the various parameters such as turntable and head speed, down force and back pressure during CMP. Using statistical analysis techniques, a better understanding of the interaction behavior between the various parameters and the effect on removal rate, no-uniformity and ETC (edge to center) is achieved.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.35D no.9
• /
• pp.20-25
• /
• 1998

Cu removal rates for various SiO$_2$ trench pitch sizes and densities and AFM images of surface profiles after global planarization using Cu CMP technology are investigated. In the experimental results, Cu removal rates are increasing as the pattern densities and pattern pitches are getting high and low, respectively, and then decreasing after local planarization. The rms roughness after global planarization are about 120$\AA$. AFM images with a 50% pattern density for 1${\mu}{\textrm}{m}$ and 2${\mu}{\textrm}{m}$ pitches show that thicknesses of 120~330$\AA$ Cu interconnects have been peeled off and oxide erosion of Cu/Sio$_2$ sidewall is observed. However, AFM images with a 50% pattern density for 10${\mu}{\textrm}{m}$ and 15${\mu}{\textrm}{m}$ pitches show that 260~340$\AA$ thick Cu interconnects have been trenched at the boundaries of Cu/Sio$_2$ sidewall.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.07a
• /
• pp.343-346
• /
• 2003

A systematic study of Cu CMP in terms of the effect of slurry chemicals(oxidizer, corrosion inhibitor, complexing agent) on the process characteristics has been performed. In acidic media, a corrosion inhibitor, benzotriazole(BTA) and tolytriazol(TTA) was used to control the removal rate and avoid isotropic etching. When complexing agent is added with $H_2O_2$ 2wt% in the slurry, a corrosion rate was presented very good. Most of in, it was appeared that BTA is possible to be replaced by TTA. The tartaric acid was distinguished for the effect among complexing agents. n we apply this results to copper CMP process, it is thought that we will be able to obtain better yield.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.11a
• /
• pp.529-529
• /
• 2007

Ruthenium (Ru) is a white metal and belongs to platinum group which is very stable chemically and has a high work function. It has been widely studied to apply Ru as an electrode material in memory devices and a Cu diffusion barrier metal for Cu interconnection due to good electrical conductivity and adhesion property to Cu layer. To planarize deposited Ru layer, chemical mechanical planarization(CMP) was suggested. However, abrasive particle can induce particle contamination on the Ru layer surface during CMP process. In this study, zeta potentials of Ru and interaction force of alumina particles with Ru substrate were measured as a function of pH. The etch rate and oxidation behavior were measured as a function of chemical concentration of several organic acids and other acidic and alkaline chemicals. PRE (particle removal efficiency) was also evaluated in cleaning chemical.

• Proceedings of the International Microelectronics And Packaging Society Conference
• /
• 2001.11a
• /
• pp.230-234
• /
• 2001

본 연구에서는 Alumina(A1$_2$O$_3$) based Slurry를 이용하여 CU CMP를 할 때 첨가제의 영향을 Removal rate와 Etch rate 측면에서 조사하였다. 각각의 첨가제의 종류와 조성의 변화에 따라 Polishing에 미치는 영향을 연구하였다. Cu의 Removal rate는 Etch rate와 달리 Organic acid의 종류에 직접적으로 영향을 받는다. Citric acid는 높은 Removal rate와 슬러리 내에서 안정성이 가장 좋은 결과를 보이고 있다. Citric acid의 농도가 증가하면 증가할수록 Removal rate는 증가하였다. BTA의 농도에 따라서 Cu의 Removal rate와 Etch rate의 감소를 확인할 수 있다. EDTA의 농도에 따라서는 증가함을 볼 수 있다.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.05c
• /
• pp.158-161
• /
• 2003

The primary aim of this study is to investigate new semi-abrasive free slurry including acid colloidal silica and hydrogen peroxide for copper chemical-mechanical planarization (CMP). In general, slurry for copper CMP consists of colloidal silica as an abrasive, organic acid as a complex-forming agent, hydrogen peroxide as an oxidizing agent, a film forming agent, a pH control agent and several additives. We developed new semi-abrasive free slurry (SAFS) including below 0.5% acid colloidal silica. We evaluated additives as stabilizers for hydrogen peroxide as well as accelerators in tantalum nitride CMP process. We also estimated dispersion stability and Zeta potential of the acid colloidal silica with additives. The extent of enhancement in tantalum nitride CMP was verified through anelectrochemical test. This approach may be useful for the application of single and first step copper CMP slurry with one package system.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2008.06a
• /
• pp.359-360
• /
• 2008

• Journal of the Microelectronics and Packaging Society
• /
• v.21 no.4
• /
• pp.117-123
• /
• 2014

Cu through-vias, which can be used as thermal vias or vertical interconnects, were formed using bottom-up electrodeposition filling as well as top-down electrodeposition filling into open via-holes and their microstructures were observed. Solid Cu through-vias without voids could be successfully formed by bottom-up filling as well as top-down filling with direct-current electrodeposition. While chemical-mechanical polishing (CMP) to remove the overplated Cu layer was needed on both top and bottom surfaces of the specimen processed by top-down filling method, the bottomup process has an advantage that such CMP was necessary only on the top surface of the sample.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2012.10a
• /
• pp.35-36
• /
• 2012