• Proceedings of the KIEE Conference
• /
• 1991.11a
• /
• pp.435-438
• /
• 1991

This work is aimed to clarify the effect of only crosslinking of polyethylene on the water tree propagation and thus the crosslinking of LDPE was made by use of $Co^{60}$ $\gamma$-ray irradiation at room temperature. For this purpose, before water tree testing under same test conditions, injection molded samples were made of LDPE using CNRS laboratory model and also some of them were irradiated under different dose rate for crosslinking. Afterwards, the aged specimens were put into microscopic investigation as a mean to compare their different morphological aspects by use of SEM for the fractured surface. The SEM observation points out that the untreed region in the irradiated PE shows the densed structure whereas that in the LDPE is not closely packed. Also in the water treed region of LDPE, the density and the dimension of voids are higher than those in irradiated PE. Based on our results, it seems that the difference in the PE structure could sufficiently contribute to cause the different water tree propagation of these materials.

• Polymer(Korea)
• /
• v.26 no.6
• /
• pp.778-784
• /
• 2002

Chemical modification of a dextran film to improve its physical properties was carried out by addition of plasticizers and crosslinking agents. Moreover, low-temperature plasma treatment with acetylene gas was done. The dextran film showed high mechanical strength but was brittle and vulnerable to moisture. When plasticizer was added, it became very soft but with large reduction of mechanical strength. However, a flexible film with fairly high mechanical strength and water resistance was prepared when the film was crosslinked by adding crosslinking agent with or after the addition of plasticizer. Treatment with an acetylene plasma changed the dextran film surface from hydrophilic to hydrophobic with little influence on the bulk properties of the film.

• Bulletin of the Korean Chemical Society
• /
• v.30 no.2
• /
• pp.334-338
• /
• 2009

Trifunctional epoxy resin triglycidyl paraaminophenol (TGPAP)/$CaCO_3$ nanocomposites were prepared using the melt blending method. The effects of nano-$CaCO_3$ content on the thermal behaviors, such as cure behavior, glass transition temperature ($T_g$), thermal stability, and the coefficient of thermal extension (CTE), were investigated by several techniques. Differential scanning calorimetry (DSC) results indicated that the cure reaction of the TGPAP epoxy resin was accelerated with the addition of nano-$CaCO_3$. When the nano-$CaCO_3$ content was increased, the $T_g$ of the TGPAP/$CaCO_3$ nanocomposites did not obviously change, whereas the crosslinking density was linearly increased. The nanocomposites showed a higher thermal stability than that of the neat epoxy resin. This result could be attributed to the increased surface contact area between the nano-$CaCO_3$ particles and the epoxy matrix, as well as the high crosslinking density in the TGPAP/$CaCO_3$ nanocomposites. The CTE of the nanocomposites in the rubbery region was significantly decreased as the nano-$CaCO_3$ content was increased.

• Journal of the Korean Chemical Society
• /
• v.53 no.3
• /
• pp.345-354
• /
• 2009

Sulfonated poly(ether sulfone)s (PESs) with a network structure were prepared by heat-induced crosslinking of the allyl-terminated telechelic sulfone polymers using a bisazide and their structure was analyzed by $^1H$ NMR. Having both uniform distribution of the hydrophilic conductive sites and controlled hydrophobic nature by minimized crosslinking, the crosslinked polymer (PES-60) membrane offered excellent proton conductivity at high temperature with a good thermal stability. In addition, selectivity of the crosslinked membrane (PES-60) was more than three times than that of Nafion$^{(R)}$.

• Polymer(Korea)
• /
• v.34 no.5
• /
• pp.391-397
• /
• 2010

Poly(amic acid)(PAA) was prepared by reaction of bicyclo(2,2,2)oct-7-ene-2,3,5,6-tetracarboxylicdianhydride(BTDA) containing double bond for crosslinking and bis[4-(3-aminophenoxy) phenyl] sulfone(BAPS) in N,N-dimethylacetamide(DMAc). The cast film of PAA was heat-treated at different temperatures to create polyimide(PI) films. With increasing thermal crosslinking temperatures from 250 to $350^{\circ}C$, the thermo-mechanical properties, degree of crosslinking, and optical transparency of the cross-linked PI were investigated. The maximum enhancement in the thermo-mechanical properties was observed at a heat treatment condition of $350^{\circ}C$. However, the optical transparency was found to be optimal for $250^{\circ}C$ heat treatment. The degree of crosslinking in NMR was determined to be 85% to 93% with increasing annealing temperature conditions from 250 to $350^{\circ}C$.

• Journal of the Korea Concrete Institute
• /
• v.16 no.1 s.79
• /
• pp.54-60
• /
• 2004

This study deals with the setting behavior of polystyrene mortars using waste expanded polystyrene(EPS) solution-based binders. The binders for polystyrene mortars are made by mixing crosslinking agent with EPS solutions prepared by dissolving EPS in styrene. Polystyrene mortars are prepared with various EPS concentrations of EPS solutions and crosslinking agent contents, subjected to a dry curing, and tested for working life, peak exotherm temperature and 10h-length change. From the test results, He working lives of polystyrene mortars are shortened with raising EPS concentration of EPS solution and crosslinking agent content. Low-shrinkage or non-shrinkage polystyrene mortars could be obtained by adjusting EPS concentration of EPS solution and crosslinking agent content.

• Polymer(Korea)
• /
• v.32 no.1
• /
• pp.1-6
• /
• 2008

The adhesion behaviors and processability of NBR as a sealing material were investigated. In order to find the optimum formulation, the adhesive properties and processability were observed as the change of the contents of acrylonitrile (ACN) in NBR. Effects of Mooney viscosity, filler, plasticizer and crosslinking agent on the adhesion behaviors were also studied. The contents of ACN in NBR have great effects on adhesion behaviors and processability in NBR sealing. To know the optimum condition of roll mixing, degree of dispersion was investigated. It was confirmed that degree of dispersion was influenced by various factors such as mixing order, time, and temperature. The crosslinking system was studied as the observation of sulfur system, peroxide system, crosslinking density, and structure. From the variation of the dry condition and hexamine contents, the relation between adhesive and NBR was studied. These results show the adhesion properties and processability are dependent on the contents of ACN and crosslinking system.

• Archives of Pharmacal Research
• /
• v.8 no.4
• /
• pp.191-195
• /
• 1985

The polymerization of title compound (MCEC, I) with phenols led to give corresponding resole type polymer. Phenol and p-methoxyphenol polymer had a relative higher molecular weight and a property of elastomer, but p-chloro-and p-nitrophenol polymer had a lower ones. Also, phenol and p-meth-oxyphenol gave to crosslinking polymer by elongation of reaction period and rising of temperature.

• Textile Coloration and Finishing
• /
• v.21 no.3
• /
• pp.1-9
• /
• 2009

Polycarboxylics acids are used as crosslinking agents for cotton cellulose to produce durable finished press cotton fabric. It has been observed that the strength of the cotton fabric treated with polycarboxylic acids showed significant reduction as a result of the crosslinking process. The effect of acid-catalyzed depolymerization on the tear strength of cotton fabric is investigated by evaluating the cotton fabric treated by succinic acid, which does not crosslink cotton cellulose and form little ester on the cotton fabric. We find that the tear strength of cotton fabric treated with succinic acid decreases at elevated temperature due to acid-catalyzed depolymerization of cellulose. The magnitude of fabric strength reduction increases as the acid concentration increases. At a constant acid concentration, it increases as the curing temperature and time increases. It decreases as the pH of the acid solution increases. We also find that the dissociation constant of an acid also has a significant effect on the fabric strength reduction. The magnitude of fabric tear strength reduction increases as the acid dissociation constant decreases.

• Polymer(Korea)
• /
• v.29 no.1
• /
• pp.91-95
• /
• 2005

The PVA hydrogels were prepared by the chemical and irradiation method to improve the heat resistance of these hydrogels at the high temperature. The physical properties such as the gel content, the degree of swelling and the gel strength for the synthesized hydrogels were examined. Gel content increased as the chemical reaction time and the irradiation dose increased, and gel content of the hydrogels were higher when the two-steps of chemical and irradiation method were used rather than only the chemical method. Gel strength increased as the chemical reaction time increased, and as the irradiation dose decreased. The hydrogels prepared by the chemical reaction for 5 hours and the two-steps had the heat resistance at the high temperature.