• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1999.11a
• /
• pp.483-486
• /
• 1999

The treeing inhibitors of barbituric acid derivatives and azocompounds effects on the electrical properties of crosslinked low density polyethylene were investigated. The electrical treeing parameters for tree inception voltage, AC breakdown strength. volume resistivity, capacitance and dissipation factor at 1Mz and thermoluminescence measurements were discussed. From the results, 4- (4-nitrophenylazo) resorcinol among the treeing inhibitors was shown good insulation characteristics.

• Polymer(Korea)
• /
• v.34 no.1
• /
• pp.74-78
• /
• 2010

In this paper, crosslinked polyethylene (PE) separators for lithium secondary batteries were prepared by an electron beam irradiation under various beam currents and dose rates. The crosslinking degree increased up to maximum 71% with an increasing absorption dose and with a decreasing beam current. The PE separators irradiated at lower beam currents showed better thermal shrinkage (51%) and mechanical properties than the original PE separator and PE separators irradiated at higher beam current. The ionic conductivity ($1.01{\times}10^{-3}\;S/cm$) and electrolyte uptake (275%) of the crosslinked PE separators were comparable to the original PE separator.

• Journal of Biomedical Engineering Research
• /
• v.20 no.1
• /
• pp.99-106
• /
• 1999

Ultra-high molecular weight polyethylene (UHMWPE) was crosslinked in the melt state to enhance wear resistance, Dicumyl peroxide (DCP) and triallyl cyanurate (TAC) was used as a crosslinking agent and a promoter, respectively. With increasing amount of DCP and TAC used, gel content of crosslinked UHMWPE (XUMPE) increased, while the melting temperature, crystallizaiton temperature, crystallinity, and tensile properties decreased. The results of pin-on-disk wear test and ball-on-disk test with small applied load showed reduced wear volumes of XUMPE from that of the unmodified UHMWPE. As the wear mechanism effected in the experimental condition of this study was thought to be deformation rather than adhesion or fatigue, a new parameter, the ratio of maximum contact stress to yield stress, was proposed to correlate well with observed wear resistance. In ball-on-disk wear test with larger applied load, XUMPE showed higher wear volumes than that of the unmodified UHMWPE which were accompanied with increased friction coefficients and surface roughness of the wear tracks. When contact stress was well above yield stress, the failure of XUMPE, as well as deformation, was thought to be much accelerated.

• Macromolecular Research
• /
• v.17 no.8
• /
• pp.580-584
• /
• 2009

The effects of crystallinity and radiation crosslinking on the physical properties of a microporous high density polyethylene (HDPE) film with Millad3988 as a nucleating agent were investigated. The pores of the HDPE film were affected by the crystallinity. The crystallinity of the HDPE films increased with increasing Millad3988 amount up to 0.1 wt% but decreased with further addition. The mechanical characteristics of the HDPE containing Millad3988 films improved with increasing irradiation dose up to 50 kGy, but decreased at 75 kGy due to severe degradation. The thermal shrinkage behavior of the HDPE films decreased with increasing radiation dose up to 50 kGy. The porosity of the stretched HDPEIMillad3988 films after ${\gamma}$-ray radiation increased with increasing y-ray radiation dose up to 50 kGy. The pores of the irradiated films were formed more easily by a stretching due to the formation of a crosslinked structure.

• Polymer(Korea)
• /
• v.35 no.4
• /
• pp.296-301
• /
• 2011

This study focuses on the investigation of the impregnation of poly (vinyl alcohol) (PVA) crosslinked with poly(styrene sulfonic acid-co-maleic acid) (PSSA-MA) to porous polyethylene membrane for the fuel cell application. The membranes were characterized by the measurements of the water content, contact angle, FTIR spectra, thermal gravimetric analysis, ion exchange capacity, proton conductivity, methanol permeability and elastic modulus. The existence of hydrophilic moieties in the impregnated membranes was confirmed by contact angle and FTIR measurements. The impregnated PVA/PSSAMA(90:10) membrane exhibited a higher ion exchange capacity (1.2 meq./g dry membrane) than Nafion membrane (0.91 meq./g dry membrane). Through the elastic modulus measurement, the dimensional stability of the resulting membranes was expected to increase higher than the polyethylene membranes. The methanol crossover and water content decreased even if the PSSA-MA content increased due to the reduction of the free volume.

• Journal of the Korean Society of Safety
• /
• v.27 no.2
• /
• pp.13-19
• /
• 2012

The effectiveness of treeing resistance in low density polyethylene containing azocompounds were investigated under radiation environments. 4-(4-nitrophenylazo)-1-naphthol and 4-(4-nitrophenylazo) resorcinol were selected for treeing inhibitors. LDPE containing the additives were crosslinked with dicumyl peroxide, irradiated by $Co^{60}$ ${\gamma}$-ray in the presence of air at room temperature. Treeing inception voltage, AC breakdown strength measurements were carried out for electrical insulation characteristics, thermoluminescence and gel contents were analyzed as various irradiation doses also. LDPE with treeing inhibitors showed much better insulation characteristics than pure LDPE. It is interpreted that molecular structures, polar groups and the type of radicals connected on the benzene ring of the additives affected electrical characteristics. From the results, 4-(4-nitrophenylazo) resorcinol was the most effective upon the best treeing and radiation resistance.

• Bulletin of the Korean Chemical Society
• /
• v.23 no.5
• /
• pp.683-687
• /
• 2002

We have investigated the effect of the number of ethylene oxide (EO) units inside poly(ethylene glycol)dimethacrylate (PEGDMA) on the ionic conductivity of its gelled polymer electrolyte, whose content ranges from 50 to 80 wt%. PEGDMA gelled polym er electrolytes, a crosslinked structure, were prepared using simple photo-induced radical polymerization by ultraviolet light. The effect of the number of EO on the ionic conductivity was clearly shown in samples of lower liquid electrolyte content. We have concluded that the ionic conductivity increased in proportion to both the number of EO units and the plasticizer content. We have also studied the electrochemical properties of 13PEGDMA (number of EO units is 13) gelled polymer electrolyte.

• Proceedings of the KIEE Conference
• /
• 2011.07a
• /
• pp.1426-1427
• /
• 2011

전기적, 기계적으로 우수한 성능을 지닌 절연재료인 폴리에틸렌은 장기간 운전 중 열화에 의해 절연성능이 저하되고 시간이 지나면서 케이블의 사고 원인을 제공하게 된다. 본 논문에서 전력용 케이블의 절연체로 널리 사용되고 있는 가교폴리에틸렌(XLPE)를 대신하여 최근 주목을 받고있는 친환경 특성을 부여하기 위한 비가교 폴리에틸렌 재료에 대한 기초적 물성(워터트리성장특성, AC 절연파괴특성, 전도전류 특성)을 실험적으로 비교분석하였다.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2000.11a
• /
• pp.77-80
• /
• 2000

In order to determine what influences the interfacial charge in EPDM/XLPE laminates, We used PEA (pulsed electroacoustic) method. Interfacial properties such as space charge accumulation and breakdown strength in crosslinked polyethylene (XLPE)/ethylene-propylene-diene monomer (EPDM) laminates were investigated. Interfacial charge develops when the EPDM is laminated with XLPE. It showed the positive polarity same as the simulation in case on intercase of EPDM/XLPE. In case of coupling agent added silicone oil, as increasing the content of coupling agent, the interfacial charge decreased. Details of the results are given and their origins discussed.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1998.11a
• /
• pp.211-214
• /
• 1998

DC breakdown characteristics and formation of space charge at the interfaces of crosslinked polyethylene (XLPE) /ethylene propylene diene terpolymer (EPDM) laminates were studied. Effects of silicone grease and some chemicals such as crosslinking coagent on the interfacial charge were also studied. Interfacial charge develops at the interface of XLPE/EPDM laminates, which changes depending on heat treatment conditions and types of chemicals coated at the interface. Some chemicals such as maleic anhydride reduce the accumulation of interfacial charge in the XLPE/EPDM laminates. Breakdown strength of EPDM/XLPE laminate through the interface was highest when silicone oil was pasted in the interfaces. Interfacial breakdown strength decreased with the increase of MAH content.