• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.35D no.7
• /
• pp.109-116
• /
• 1998

In this work was produced and analyzed a z-cut Ti:LiNbO$_{3}$ optical waveguide which applies for various optical devices.A waveguide channel with a thickness 8 .mu.m and a length 66,000.mu.m and a mach-zehnder interferometer type waveguide were fabricated at a diffusion temperature 1050.deg. C for 6-8hours in a wet $O_{2}$ environment. The resulting Ti:LiNbO$_{3}$ optical waveguide was measured to have a Ti-strip thickness of 950.angs. and low loss. Surfaces and cross-sections of a fabricated waveguide were analysed. The mode pattern anaysis revealed that the waveguide showed a single mode at a 1550nm wavelength. The effective dimension of the waveguide was calculated by measuring a gaussian profile; Wx=10.95.mu. and Wy=9.14.mu.m. a propagation loss, of 0.50dB/cm for a TM mode and 0.45dB/cm for a TE mode, was low enough to be accepatable for optical devices.

• Proceedings of the KSR Conference
• /
• 2007.05a
• /
• pp.444-447
• /
• 2007

The free flow of fine bubbles generated by electrolysis and smoke flow in a space enclosed by fire were recently found to show the same tendency thus leading to the introduction of a research technique. The research experimentally models smoke diffusion and flow in parallel and slanted tunnels using the fine hydrogen bubbles generated by electrolysis in a water tank. Visualization laser with wavelength of 532nm and output power of 1000mW is used to visualize effectively the cross section of fine hydrogen bubble flows generated in a model tunnel.

• Journal of the Korean Vacuum Society
• /
• v.12 no.S1
• /
• pp.40-45
• /
• 2003

Ru interfacial layer was inserted into Mo-on-Si interface to enhance the extreme ultra-violet (EUV) reflective multilayer properties. The stacking status and optical properties are analyzed using cross-sectional transmission electron microscope (TEM), and reflectometer. About 1.5% of maximum reflectivity can be acquired as predicted in optical simulation, which is thought to be originated from the diffusion inhibition property. Phase defect correctability of the multilayer can be enhanced by the insertion of Ru barrier layer.

• Proceedings of the KSME Conference
• /
• 2008.11a
• /
• pp.1758-1760
• /
• 2008

Under typical operating conditions, flows in microfluidic devices are laminar and molecular diffusion across the channels is slow, which makes an efficient mixing in microfluidic devices difficult to achieve. The mechanism to achieve effective mixing in laminar flows is that of repetitive stretching and folding. Essential is to generate spatially periodic flows with crossing cross sectional streamlines. A mapping method is employed to analyze mixing in micromixers, enabling us to investigate the progress of mixing both qualitatively and quantitatively. The progress of mixing is characterized by a measure of mixing, called the discrete intensity of segregation. The mapping method is applied to mixing in such micromixers as the staggered herringbone mixer, the barrier embedded micromixer, and the three-dimensional serpentine channel to demonstrate the capability of the numerical scheme to tackle general mixing problems in microfluidic devices.

• Journal of Microbiology and Biotechnology
• /
• v.5 no.4
• /
• pp.229-233
• /
• 1995

Acremonium chrysogenum was immobilized in ionotropic gel beads to develop semi-continuous production of cephalosporin C (CPC). Barium alginate beads were more stable than calcium alginate or strontium alginate beads in chemically defined media. The gel stability of Ba-alginate was further increased by cross-linking with polyethyleneimine (PEI). The presence of carboxymethyl cellulose inside Ba-alginate beads did not reduce mass transfer resistance. Ba-alginate microbeads that had little diffusion limitation increased CPC production rate 1.6 fold higher than that of normal beads. CPC fermentation with immobilized cells in Ba-alginate microbeads was performed continuously for 40 days by way of repeated fed-batch operations. Mathematical modeling was developed to describe the repeated fed-batch fermentation system. Results of the computer simulation agreed well with the experimental data, which made it possible to predict an optimal feeding rate that could maximize total CPC productions.

• Journal of Advanced Marine Engineering and Technology
• /
• v.17 no.2
• /
• pp.52-59
• /
• 1993

This study is investigated of tensile and fatigue strength for advanced composite materials under hygrothermal environment. The materials used are two types of Carbon/Epoxy reinforced composite materials i.e., 13$0^{\circ}C$ cure-type composite T-1/347, and 18$0^{\circ}C$ cure-type MM-1/982X. These are composed by cross-ply laminates. Test condition is the distilled water of 8$0^{\circ}C$. The separate absorption contents estimated by the Fick's diffusion rule are similar to the experiment results. The tensile strength of T-1/347 wet specimens more increased than that of dry ones, but that of MM-1/982X decreased. The fatigue strengthes of both T-1/347 and MM-1/982X wet specimen more decreased than those of dry specimens.

• Journal of the Korean Society of Combustion
• /
• v.5 no.1
• /
• pp.55-66
• /
• 2000

A general purpose program for the analysis of flows in a gas turbine combustor is developed. The program uses non-staggered grids based on finite volume method and the cartesian velocities as primitive variables. A flow inside the C-type diffuser is simulated to check the boundary fitted coordinate. The velocity profiles at cross section agree well with experimental results. A turbulent diffusion flame behind a bluff body is simulated for the combustion simulation. Simulated results show good agreement with experimental data. Finally, a turbulent flow with swirl in a gas turbine combustor was simulated. The results show two recirculating region and simulated velocity fields agree well with experimental data. The distance between two recirculating regions becomes shorter as swirl angle increases. Swirl angle changes angular momentum and streamlines in flow fields.

• Progress in Superconductivity
• /
• v.1 no.1
• /
• pp.51-55
• /
• 1999

A Ni/Ag/Stainless steel 310S(SS310S) multi-layer sheet has been fabricated by a combination of vacuum brazing, cold rolling and texture annealing processes. After heat-treating the thin Ni/Ag/SS310S multi-layer sheet at $900^{\circ}C$ for 2h, development of (100)<001>cube texture on Ni surface was revealed by (111) pole figure. Quantitative chemical analysis was made by EPMA for the cross-section of the Ni/Ag/SS310S multi-layer sheet. EPMA results showed that Ag diffusion into the Ni layer, which may suppress the cube texture development, was negligible. A small amount of Cr atoms were detected in the Ni layer. It showed that Ag can be used as a chemical barrier of alloying element atoms in Ni layer for the Ni/Ag/SS310S multi-layer sheet and a strong cube texture was developed for the Ni layer in the Ni/Ag/SS310S multi-layer sheet.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.13 no.4
• /
• pp.359-364
• /
• 2000

The paper describes the electron transport characteristics in SP$_{6}$+He gas calculated E/N values 0.1~700[Td] by the Monte Carlos simulation and Boltzmann equation method using a set of electron collision cross sections determined by the authors and the values of electron swarm parameters obtained by TOF method. This study gained the values of the electron swarm parameters such as the electron drift velocity the electron ionization or attachment coefficients longitudinal and transverse diffusion coefficients for SF$_{6}$+He gas at a range of E/N.E/N.

• Proceedings of the KIEE Conference
• /
• 2001.07e
• /
• pp.72-75
• /
• 2001

In this paper, we describe the results of a combined experimental theoretical study designed to understand and predict the dielectric properties of $SF_6$ and $SF_6+Ar$ mixtures. The electron transport, ionization, and attachment coefficients for pure $SF_6$ and gas mixtures containing $SF_6$ has been analysed over the E/N range $30{\sim}300Td$ by a two term Boltzrnann equation and by a Monte Carlo Simulation using a set of electron cross sections determined by other authors, experimentally the electron swarm parameters for 0.2% and 0.5% $SF_6+Ar$ mixtures were measured by time- of- flight method, The results show that the deduced electron drift velocities, the electron ionization or attachment coefficients, longitudinal and transverse diffusion coefficients and mean energy agree reasonably well with the experimental and theoretical for a rang of E/N values.