• 한국구조물진단유지관리공학회 논문집
• /
• 제10권1호
• /
• pp.173-182
• /
• 2006

곡선거더교의 설계에서 I형 병렬, 1박스, 2박스의 거더 형태의 교량은 휨과 비틀림을 동시에 발생함으로 그 응력은 매우 복잡하다. 일반적으로 비틀림은 순수 비틀림과 휨 비틀림으로 구성되어 있으므로 곡선거더교의 발생되는 응력들을 결정하는 절차는 매우 어렵다. 전달행렬법은 이론적인 배경과 적용이 매우 쉬운 장점 때문에 구조해석 분야에서 많이 사용되고 있으며, 유한차분법과 비교하여 신뢰성을 검증하여 좋은 결과를 얻었다. 따라서, 본 연구에서는 I형 병렬 곡선교, 1박스거더 곡선교, 2박스 거더 곡선교에 대한 비틀림 정수비와 비틀림 의한 비틀림 응력비 사이 관계를 비교 검토하여 휨 비틀림에 의한 응력해석을 생략할 수 있는 비틀림 정수비의 한계 값을 분석하였다.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2005년도 춘계 학술발표회 논문집
• /
• pp.916-923
• /
• 2005

In this study, to observe aging effect of undrained shear behavior for Nak-Dong River sand, undrained static and cyclic triaxial tests were performed with changing relative density ($D_r$), consolidation stress ratio($K_c$) and consolidation time. As a result of the test, the modulus of elasticity to all samples estimated within elastic zone by the micro strain of about 0.05% in case of static shear behavior increased with the lapse of consolidation time significantly, so aging effect was shown largely. Also strength of phase transformation point(S_{PT}$) and strength of critical stress ratio point($S_{CSR}$) increased with the lapse of consolidation time. Undrained cyclic shear strength($R_f$) obtained from the failure strain 5% increased in proportion to relative density($D_r$) and initial static shear stress($q_{st}$), $R_f$ of consolidated sample for 1,000 minutes increased about 10.6% compared to that for 10 minutes at the loose sand, and $R_f$ increased about 7.0% at the medium sand. In situ application range of $R_f$ to the magnitude of earthquake for Nak-Dong River sand was proposed by using a increasing rate of $R_f$ as being aging effect shown from this test result.

• Journal of Advanced Marine Engineering and Technology
• /
• 제28권7호
• /
• pp.1131-1137
• /
• 2004

Recently there has been a remarkable increase in the number of high speed and large ships and the high power involved for propulsion of above ships has brought high pitch ratio and highly skewed propeller. The recent tendency toward highly skewed propeller has increased the load on propeller blades, and the fatigue strength of propeller blades has become the critical point in design of propellers for ships. In this paper the effect of stress ratio and skew angle on the fatigue strength of highly skewed propeller, the statistical inference on the total revolutions of highly skewed propeller for 20 years under normal sea going state. and so on have been discussed. On the basis of above discussions, the highly skewed propeller blade thicknesses by the rules of classification society and the standards of manufacturer in country were compared and reviewed.

• 한국자동차공학회논문집
• /
• 제4권4호
• /
• pp.171-178
• /
• 1996

DCB(pure mode I) and CLS(mixed mode) tests were performed to investigate the effect of fracture mode on the interlaminar fracture of composite laminate. Mode I critical strain energy release rate was found to be $133J/m^2$ from the DCB test and total strain energy release rate decreased from $1, 270J/m^2$ as thickness ratio(tl/t) varied from 0.333 to 0.667 from the crease from the CLS test. Crack length had no effect on the total strain energy release rate and load was almost constant during the crack growth of the specimen which had the specific thickness ratio. Crack initiated when the stress of the strap ply reached constant stress $42kgf/mm^2$ which was found to be independent of the thickness ratio.

• Geomechanics and Engineering
• /
• 제27권5호
• /
• pp.497-509
• /
• 2021

A large deformation FEM (Finite Element Method) based numerical analysis has been performed to study the behaviour of the bell-shaped anchor embedded in undrained saturated (cohesive) soil with the help of finite element based software ABAQUS. A typical model anchor with bell-diameter of 0.125 m, embedded in undrained saturated soil with varying cohesive strength (from 5 kN/m² to 200 kN/m²) has been chosen for studying the characteristic behaviour of the bell-shaped anchor installed in cohesive soil. Breakout factors have been evaluated for each case and verified with the results of experimental model tests for three different types of soil samples. The maximum value of breakout factor was found as about 8.5 within a range of critical embedment ratio of 2.5 to 3. An explicit model has been developed to estimate the breakout factor (F_c) for uplift capacity of bell-shaped anchor within clay mass in terms of H/D ratio (embedment ratio). It was also found that, the ultimate uplift capacity of the anchor increases with the increase of the value of cohesive strength of the soil and H/D ratio. The empirical equation developed in the present investigation is usable within the range of cohesion value and H/D ratio from 5 kN/m² to 200 kN /m² and 0.5 to 3.0 respectively. The proposed model has been validated against data obtained from a series of model tests carried out in the present investigation. From the stress-profile analysis of the soil mass surrounding the anchor, occurrence of stress concentration is found to be generated at the joint of anchor shaft and bell. It was also found that the vertical and horizontal stresses surrounding the anchor diminish at about a distance of 0.3 m and 0.15 m respectively.

• 드라이브 ㆍ 컨트롤
• /
• 제14권1호
• /
• pp.1-7
• /
• 2017

The power train of a concrete truck mixer reducer includes differential planetary gears to get a large reduction ratio for operating the mixer drum in a compact structure. These differential planetary gears are a very important part of the mixer reducer where strength problems are the main concern. Gear bending stress, gear compressive stress and scoring failure are the main concerns. Many failures in differential planetary gears are due to the insufficient gear strength and resonance problems caused by major excitation forces such as gear mating failure in the transmission. In the present study, where the excitation frequencies are the gear tooth passing frequencies of the mating gears, a Campbell diagram is used to calculate differential planetary gear critical speeds. Mode shapes and natural frequencies of the differential planetary gears are calculated by CATIA V5. These are used to predict gear resonance failures by comparing the working speed range with the critical speeds due to the gear transmission errors of the differential planetary gears.

• 한국지반공학회지:지반
• /
• 제8권2호
• /
• pp.45-58
• /
• 1992

지반재료의 탄소성 구성 모델은 유연성과 안정성을 동시에 만족하여야 공학적으로 의미를 가지며 실용적으로 사용될 수 있다. 본 연구에서는 안정성이 있는 계수를 사용하는 수정 Cam-clay 모델을 근간으로, 한계상태 간격비를 계수로 도입하여 더욱 유연성이 있는 모델을 제안하였다. 한계상태 간격비는 추가적인 실험없이 간편하게 구할 수 있으며 특히 비배수 전단거동에 대하여 실용적으로 사용될 수 있다. 제안된 모델은 비 배수전단 삼축압축시험에 대하여 응력경로 및 응 력-변형률관계를 수정 Cam-clay 모델에 비하여 매우 정확하게 예측할 수 있었다. 뿐만 아니라 전단변형률 속도, 크리프 및 응력이완의 영향을 고려할 수 있었다. 특히 실제의 상태경계면을 표현 탄성 -완전소성모델, 사용해야 삼축압축시험중 비 배수시험이 W W 삼축압축시험시 전단시험을 논문에서 해석한 점토질 지반의 거동에 대하여 관련유동칙을 따른다는 가정이 잘 적용되기 때문이라고 판단된다.

• 한국해양공학회지
• /
• 제18권5호
• /
• pp.43-49
• /
• 2004

The lightness of components required in the automobile and machine industry necessitates the use of high strength components. In particular, the fatigue failure phenomena, which occurs when using metal, increases the danger to human life and property. Therefore, antifatigue failure technology is an integral part of current industries. Currently, the shot peening is used for removing the defect from the surface of steel, while improving the fatigue strength on surface. Therefore, in this paper, the effect of compressive residual stress of spring steel(JISG SUP-9) by shot-peening on fatigue crack growth characteristics in a stress ratio(R=0.1, R=0.3, R=0.6) was investigated, giving consideration to fracture mechanics. By using the methods mentioned above, following conclusions are drawn: (1) The fatigue crack growth rate(da/dN) of the shot-peening material was lower than that of the un-peening material and in stage I, ΔKth, the threshold stress intensity factor of the shot-peen processed material is high in critical parts, unlike the un-peening material. Also m, fatigue crack growth exponent and number of cycle of the shot-peening material, was higher than that of the un-peening material, as concluded from effect of da/dN. (2) Fatigue life shows more improvement in the shot-peening material than in the un-peening material, and the compressive residual stress of surface on the shot-peen processed operate resistance of fatigue crack propagation.

• 대한기계학회논문집A
• /
• 제27권6호
• /
• pp.946-953
• /
• 2003

A FEM-based analytical approach was used to evaluate the multiaxial high cycle fatigue damage of an automotive sub-frame. Elastic Multi Body Simulation (MBS) has been applied in order to determine the multiaxial load histories. The stresses due to these loads have been given by FE computation. These results have been used as the input for the multiaxial fatigue analysis. For the assessment of multiaxial high cycle fatigue damage, the signed von Mises, the signed Tresca, the absolute maximum principal stress and critical plane methods have been employed. In addition, the biaxiality ratio, a$\sub$e/, the absolute maximum principal stress, $\sigma$$\sub$p/ and the angle, $\phi$$\sub$P/, between $\sigma$$\sub$1/ and the local x-axis, have been calculated to evaluate the stress state at each node.

• Steel and Composite Structures
• /
• 제35권4호
• /
• pp.555-566
• /
• 2020

This paper aims to present an analytical methodology to investigate influences of nanoscale and surface energy on buckling stability behavior of perforated nanobeam structural element, for the first time. The surface energy effect is exploited to consider the free energy on the surface of nanobeam by using Gurtin-Murdoch surface elasticity theory. Thin and thick beams are considered by using both classical beam of Euler and first order shear deformation of Timoshenko theories, respectively. Equivalent geometrical constant of regularly squared perforated beam are presented in simplified form. Problem formulation of nanostructure beam including surface energies is derived in detail. Explicit analytical solution for nanoscale beams are developed for both beam theories to evaluate the surface stress effects and size-dependent nanoscale on the critical buckling loads. The closed form solution is confirmed and proven by comparing the obtained results with previous works. Parametric studies are achieved to demonstrate impacts of beam filling ratio, the number of hole rows, surface material characteristics, beam slenderness ratio, boundary conditions as well as loading conditions on the non-classical buckling of perforated nanobeams in incidence of surface effects. It is found that, the surface residual stress has more significant effect on the critical buckling loads with the corresponding effect of the surface elasticity. The proposed model can be used as benchmarks in designing, analysis and manufacturing of perforated nanobeams.