• Journal of Pharmaceutical Investigation
• /
• v.29 no.3
• /
• pp.193-203
• /
• 1999

In order to investigate systematically the steady shear flow properties of aqueous po1y(ethylene oxide) (PEO) solutions having various molecular weights and concentrations, the steady flow viscosity has been measured with a Rheometrics Fluids Spectrometer (RFS II) over a wide range of shear rates. The effects of shear rate, concentration, and molecular weight on the steady shear flow properties were reported in detail from the experimentally measured data, and then the results were interpreted using the concept of a material characteristic time. In addition, some flow models describing the non-Newtonian behavior (shear-thinning characteristics) of polymeric liquids were employed to make a quantitative evaluation of the steady flow behavior, and the applicability of these models was examined by calculating the various material parameters. Main results obtained from this study can be summarized as follows: (1) At low shear rates, aqueous PEO solutions show a Newtonian viscous behavior which is independent of shear rate. At shear rate region higher than a critical shear rate, however, they exhibit a shear-thinning behavior, demonstrating a decrease in steady flow viscosity with increasing shear rate. (2) As an increase in concentration and/or molecular weight, the zero-shear viscosity is increased while the Newtonian viscous region becomes narrower. Moreover, the critical shear rate at which the transition from the Newtonian to shear-thinning behavior occurs is decreased, and the shear-thinning nature becomes more remarkable. (3) Aqueous PEO solutions show a Newtonian viscous behavior at shear rate range lower than the inverse value of a characteristic time $1/{\lambda}_E$, while they exhibit a shear-thinning behavior at shear rate range higher than $1/{\lambda}_E$. For aqueous PEO solutions having a broad molecular weight distribution, the inverse value of a characteristic time is not quantitatively equivalent to the critical shear rate, but the power-law relationship holds between the two quantities. (4) The Cross, Carreau, and Carreau-Yasuda models are all applicable to describe the steady flow behavior of aqueous PEO solutions. Among these models, the Carreau-Yasuda model has the best validity.

• Applied Chemistry for Engineering
• /
• v.22 no.4
• /
• pp.384-389
• /
• 2011

We made suspension of fumed silica in polyethylene glycol (PEG), studied rheological behavior as functions of contents of silica, dispersion condition, PEG molecular weight, temperature and contents of humidity. Rheological behavior of suspension was determined critical shear rate and rise of viscosity using rheometer AR2000. Suspension were PEGs of molecular weight 200, 400, and 600. Fumed silica suspensions of which silica contents are 5, 7, 9, 13, and 18% were prepared by normal mixing, homogenization and bead milling process. We observed their rheological behaviors at 10, 20, 30, and $40^{\circ}C$. As the PEG molecular weight and contents of silica increase, the critical shear rate was lowered. As the temperature increased, the critical shear rate was increased. Humidity contents of dispersion don't influence on the critical shear rate, but dispersion processes greatly affect the critical shear rate. The critical shear rate of suspensions prepared by the mixing process was the lowest, and that of suspensions prepared by the bead milling process was the highest. The rise in the shear viscosity of suspensions prepared by the mixing process is higher than that of suspensions prepared by the bead milling process. This was dependent on the dispersion condition of silica particle by dispersion process.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2002.03a
• /
• pp.337-342
• /
• 2002

A new apparatus called the EFA (Erosion Function Apparatus) has been built and tested to measure the erodibility of fine-grained soils. The EFA is a simple test to predict the erosion rate of fine-grained soils along with the corresponding velocity and shear stress. In addition, it is advantageous in predicting the scour rate for actual soil samples from bridge sites. The plot of erosion rate versus shear stress is the result of an EFA test. It Indicates the critical shear stress at which erosion starts and the rate of erosion beyond that shear stress. In order to measure the erodibilities of various soils, 14 Shelby Tube soil samples are collected from the actual bridge sites and tested using the EFA. The results of the EFA tests which are the relationships between erosion rates and shear stresses are presented in this paper and research continues to develop the correlation between the erosion function and the soil properties.

• Journal of Advanced Marine Engineering and Technology
• /
• v.18 no.1
• /
• pp.101-113
• /
• 1994

This research has presented and experimental investigation on the characteristics of turbulent wake past a rectanular cylinder, according to various width/height ratio such as B/H=2.0, 2.79, 3.0, and 4.0 in a uniform shear flow. In order to perform this study, a special shear flow generator which produces the uniform shear flow has been designed and manufactured. It is found that the characteristics of the wake in a uniform shear flow are quite different from those of a uniform flow and vary with shear rate. And also, the formation of regular vortex structure is concerned with shear rate.

• Korea-Australia Rheology Journal
• /
• v.15 no.2
• /
• pp.63-73
• /
• 2003

An experimental technique was developed to determine the strain-rate in a tensile specimen. Then one can calculate the transient isothermal elongational viscosity. Both shear and elongational viscosities were measured to study the effect of shear and elongational fields on the flow properties. The comparison between these viscosities shows that the onset of rapid viscosity growth as crystallization solidification proceeds occurs at about the same value of time at very small deformation rates (0.0028 and 0.0047 $s^{-1}$). The comparison of these measured viscosities as functions of shear and elongational Hencky strains also reveals that the onset of rapid viscosity growths starts at critical Hencky strain values. The behaviour of steady shear viscosity as function of temperature sweep was also explored at three different low shear rates. Finally, the influence of changing oscillatory frequencies and strain rates was also investigated.

• Proceedings of the Membrane Society of Korea Conference
• /
• 2008.05a
• /
• pp.33-47
• /
• 2008

Non-equilibrium (irreversible) themodynamics is used to investigate colloidal back-diffusion during crossflow membrane filtration. The chemical potential is generalized as a superposition of equilibrium and irreversible contributions, originating from Brownian and shear-induced diffusion, respectively. As a result, an effective drag force is derived using the irreversible thermodynamics for a particle undergoing both Brownian and shear-induced diffusion in a sheared concentrated suspension. Using the drag force, a hydrodynamic force bias Monte Carlo method is developed for crossflow membrane filtration to determine the critical flux of hard sphere suspensions. Effects of shear rate and particle size on the critical flux are studied, and results show a good agreement with experimental observations reported in the literature.

• Korea-Australia Rheology Journal
• /
• v.20 no.2
• /
• pp.51-58
• /
• 2008

This paper describes a two-step Tikhonov regularization procedure for converting the steady shear data generated by parallel-disk viscometers, in the presence of wall slip, into a shear stress-shear rate function and a wall shear stress-slip velocity functions. If the material under test has a yield stress or a critical wall shear stress below which no slip is observed the method will also provide an estimate of these stresses. Amplification of measurement noise is kept under control by the introduction of two separate regularization parameters and Generalized Cross Validation is used to guide the selection of these parameters. The performance of this procedure is demonstrated by applying it to the parallel disk data of an oil-in-water emulsion, of a foam and of a mayonnaise.

• Journal of Korea Foundry Society
• /
• v.14 no.5
• /
• pp.438-446
• /
• 1994

The effect of various thermomechanical treatments on the structure and rheological behaviour of Al-6.2wt%Si alloy in its solidification range were investigated using a Searle type high temperature viscometer. During continuous cooling, the viscosity increases gradually with increasing fraction of solidified alloy, until a critical fraction of solidified alloy is reached above which the viscosity sharply increases. The viscosity of the slurry, at a given volume fraction wolid, decreased with increasing shear rate. The size and morphology of primary solid particles during stirring is influenced strongly by shear rates, cooling rates, volume fraction and stirring time of solid. Morphological changes during stirring as a function of solid volume fractions, shear rate and processing time were also reported. In this study, the size of primary solid particles in these alloys consistently increases and the it`s aspect ratio decrease with the increase in fraction solid and decrease in shear rate. Crystal morphology changes from rosette type to spheroid type with the increase in shear rate and solid fraction.

• Korea-Australia Rheology Journal
• /
• v.12 no.3_4
• /
• pp.175-179
• /
• 2000

Rheological properties of chitosan solutions were investigated as a function of polymer concentration. The viscosity curves for chitosan solutions consisted of two distinct viscosity regions, the Newtonian zero-shear viscosity (η$_{0}$) region and the shear rate dependent apparent viscosity (η$_{app}$) region. The shear rate dependence of viscosity was more clearly observed at higher chitosan concentrations. The critical coil overlap parameter (C＊〔η〕) was determined to be approximately 3.2 from a plot of zero-shear specific viscosity η$_{sp,0}$ vs coil overlap parameter (C〔η〕), which was lower than C〔η〕4.0 reported for other random coil polysaccharides. It was also found that the slope of η$_{sp,0}$ vs C〔η〕 was 3.9 at concentrated C〔η〕>C＊〔η〕domain, while 1.2 at dilute C〔η〕$_{0}$ ${\gamma}$/${\gamma}$$_{0.8}$ relation.ion.n.n.

• Journal of the Korean Society for Precision Engineering
• /
• v.8 no.4
• /
• pp.107-117
• /
• 1991

The dynamic stability problem of nonconservative system is one of the important problems. In this study, flexible missile with mass variation is regarded as a free Timoshenko beam subjected to a controlled follower force. The stability was studied numerically through the finite element method. Through the study, the obtained results are as follows: [1] Without force direction control (1) In the case of no mass reduction, the existence of concentrated mass increases critical follower force. (2) Mass reduction rate of the beam slightly effects on the change of critical follower force. [2] With force direction control (1) Shear deformation parameter S contributes insignificantly to the force at instability when $S{\geq}10^4$. (2) With mass variation, increase of concentrated mass increases critical follower force at instbility. (3) The type of promary instability is determined by the sensor location.