• 한국자동차공학회논문집
• /
• 제11권1호
• /
• pp.128-136
• /
• 2003

In today's design trend of vehicle structure, crush zone is fiequently reinforced by adding a box-shaped sub-frame in order to avoid an excessive deformation against a high-speed offset barrier such as EU Directive 96/97 EC, IIHS offset test. That kind of vehicle structure design results in a relatively monotonic crash pulse for airbag ECU(Electronic Control Unit) located at non-crush zone. As for an angular crash event, the measured crash signal using a single-axis accelerometer in a longitudinal direction is usually weaker than that of frontal barrier crash. Therefore, it is not so easy task to achieve a satisfactory crash discrimination performance for offset and angular crash events. In this paper, we introduce a new crash discrimination algorithm using an electronic X-Y 2-axis accelerometer in order to improve crash discrimination performance especially for those crash events. The proposed method uses a crash signal in lateral direction(Y-axis) as well as in longitudinal direction(X-axis). A crash severity measure obtained from Y-axis acceleration is used to improve the discrimination between fire and no-fire events. The result obtained by the proposed measure is logically ORed with an existing algorithm block using X-axis crash signal. Simulation and pulse injection test have been conducted to verify the performance of proposed algorithm by using real crash data of a 2,000cc passenger vehicle.

• 한국자동차공학회논문집
• /
• 제20권1호
• /
• pp.106-111
• /
• 2012

Recently the usage of bicycle has increased steeply in Korea owing to traffic culture of well- being. In a car to bicycle accident investigation, the throw distance of bicycle is very important factor for reconstructing of the accident. The variables that influence on the throw distance of bicycle can be classified into the factors of vehicle and bicycle. Simulations and collision tests in actual car to bicycle accident were executed for obtaining throw distance of bicycle. The simulations were done by PC-$CRASH^{TM}$ and for actual crash tests sand bags were used for the behavior of bicyclist instead of dummy. Factors considered were vehicle velocity and the moving angles of bicycle, also the types of bicycle and vehicle were fairy cycle and automobile, respectively. From the results, the throw distances of a head-on tire collision of $0^{\circ}$ direction was longer than that of tire crash test of $45^{\circ}$ direction, and the throw distances of a head -on frame crash test of $90^{\circ}$ direction was longer than that of frame crash test of $45^{\circ}$ direction. In addition restitution coefficient between vehicle and bicycle was estimated as about 0.1 with based on actual crash tests. Finally the increaser vehicle velocity the longer the throw distances of bicycle, and the results of simulation were relatively good agreement to the experimental results.

• 한국자동차공학회논문집
• /
• 제14권5호
• /
• pp.79-83
• /
• 2006

The present low speed crash regulations and RCAR test for insurance estimate do not tend to reflect car crash occurred on a road. Therefore, car makers are trying to readjust test standard be similar to a real situation. Passenger cars and SUV vehicles on the market will be subject to this study for car to car crash. In addition, we will discuss improvement of test methods for a low speed crash and direction of bumper design by performing this impact analysis.

• 한국기계가공학회지
• /
• 제11권2호
• /
• pp.92-97
• /
• 2012

In the present the usage of bicycle has increased steeply due to well-being and convenient way of movement. In car to bicycle accident, the throw distance of bicycle is very important factor for estimating collision situation. In this study, simulations and collision tests in actual car to bicycle were executed for obtaining throw distance of bicycle. The simulations were executed by PC-CRASHTM s/w with vehicle of sedan type. Sand bags were used for the behavior of bicyclist instead of dummy and factors considered were vehicle velocity, the crashed angles and part of bicycle to vehicle, and bicycle was adult type. From the results, the throw distances of tire collision of 00 was longer than that of 450 tire crash, and the throw distances of 900 frame crash were longer than those of 450 frame crash. With based on actual crash tests and simulations, restitution coefficient of between vehicle and bicycle was estimated as 0.1. Finally the increaser vehicle velocity the longer the throw distances of bicycle and the simulation results were relatively good agreement to the results of experiment.

• 한국IT서비스학회지
• /
• 제21권6호
• /
• pp.127-145
• /
• 2022

Luna Coin, which ranked eighth in the global market capitalization and established itself as a super-large stablecoin, plunged overnight, shocking the market. Therefore, this study proposed the direction of Korea's stablecoin regulation, focusing on the Terra-Luna situation, starting with the question of whether the stable coin's value, 'stability', can be trusted. The whole story of the Terra-Luna incident was examined in depth and the problems were pointed out, and the direction of domestic stable coin regulation was described based on overseas cases. In the absence of any legal guidelines for stablecoin at the moment, we hope that this study will provide a minimum stabilizer in the virtual asset market and help protect investors.

• 자동차안전학회지
• /
• 제5권1호
• /
• pp.11-15
• /
• 2013

Small overlap crash caused fatal injury in real-world crash. IIHS(Insurance Institute for Highway Safety) proposed the small overlap test. The objective of this study is to analyze dummy injury criteria and dummy excursion on the sled reinforced body angle. Result of the comparisons of dummy injury criteria of a head, neck, and chest was best correlation between sled and vehicle test on base $angle+3^{\circ}$. However, lower extremity was not correlation because sled test could not copy of intrusion. There were a correlation between dummy movement and sled reinforced body angle. Sled reinforced body angle affects the lateral direction of excursion more than longitudinal excursion.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2007년도 춘계학술대회 논문집
• /
• pp.1564-1570
• /
• 2007

There are normally two types of the energy absorbers used in the crashworthiness of trains. The first is a structure type, which mainly used in not only the primary structures of the train but also the crash energy absorbers at the accident. The second is a module type, which just absorbs the crash energy independent of the primary structures and attached to the structures of the train. The expansion and inversion tube are widely used as the module type crash energy absorbers, especially in the train. The tubes should not be buckled under the load acting on the end of the tube in longitudinal direction during absorbing the crash energy. The buckling stability of the tubes is affected by the boundary conditions, thickness and length of tube. In this study, the effects of the length and thickness of the tubes on the buckling load are studied by using the ABAQUS, a commercial finite element analysis program, and then presents the guideline to design the tube. The analysis processes to compute the buckling load consist of a linear buckling analysis and a nonlinear post-buckling analysis. The buckling modes are evaluated by the linear buckling analysis, as using these modes, the buckling loads are computed by the nonlinear post-buckling analysis.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2007년도 춘계학술대회A
• /
• pp.774-779
• /
• 2007

The crash energy absorbers used in the trains normally are classified into two types. The first is the structure type, which mainly used in not only the primary structure of train but also the crash energy absorbers at the critical accidents. The second is the module type, which just absorbs the crash energy independently and attached onto the structures of the trains. The expansion tube is widely used as the module type of the crash energy absorbers, especially in the trains that have a heavy mass. Since the crash energy is absorbed by means of expanding the tube in the radial direction, the features of the expansion tube have the uniform load during the compression. As the uniform load remains in sudden impact, the expansion tube is effective to decrease acceleration of passengers when the train accident occur. The buckling instability of the expansion tubes is affected by the boundary conditions, thickness and length of tube. In this study, the effects of the length and thickness of the expansion tubes under the arbitrary load on the buckling are studied using the ABAQUS/standard and ABAQUS/explicit, a commercial finite element analysis program, and then presents the guideline to design the expansion tubes. The analysis processes to compute the buckling load consist of the linear buckling analysis and the nonlinear post-buckling analysis. To analysis the nonlinear post-buckling analysis, the geometry imperfections are introduced by applying the linear buckling modes to nonlinear post-buckling analysis.

• 한국전산구조공학회논문집
• /
• 제24권5호
• /
• pp.499-506
• /
• 2011

본 연구에서는 컴퓨터 시뮬레이션을 통해 복합소재 교량용 방호울타리의 성능을 분석하였다. 복합소재 방호울타리는 SB4등급을 선정하였다. 복합소재의 적층을 고려하기 위해 LS-DYNA에서 제공하는 재료모델 MAT58을 사용하였다. 복합소재는 섬유와 수지의 종류 및 섬유의 방향에 따라 성능이 상이하다. 수지는 폴리우레탄, 섬유는 유리섬유를 사용하였다. 본 논문에서는 섬유의 방향성이 다른 3가지 적층 설계안에 대해서 충돌 시뮬레이션을 수행하여 성능을 비교 평가하였다. 실차충돌 실무 업무편람에 따라 구조적 강도성능, 탑승자 보호성능, 충돌 후 차량의 거동, 가드레일의 비산에 대한 성능 평가를 실시하였다. 그 결과 적층 설계의 횡 방향 섬유의 양이 많아질수록 충돌 시뮬레이션에서 더 좋은 성능을 나타내었다.

• Journal of Ship and Ocean Technology
• /
• 제6권3호
• /
• pp.37-45
• /
• 2002

A series of detailed study was performed to identify the sources of the propeller blade failure and resolve the problem systematically, by use of the theoretical tools and by the direct measurement and observation in the full-scale sea trials. The selection of inexperienced propulsion control system with a reversible gear system is shown to cause the serious damage to the propeller blades in crash astern maneuver, when the rotational direction of the propeller is changed rapidly. Quasi-steady analysis for propeller blade strength using FEM code in bollard backing condition indicates that the safety factor should be order of 18∼20 to avoid the structural failure for the selected propeller geometry and reduction gear system.