• Transactions of the Korean Society of Automotive Engineers
• /
• v.21 no.5
• /
• pp.97-103
• /
• 2013

Crash performance of the straight member was studied by FE analysis. One end of model was fixed and the other end was impacted by 1,000kg rigid mass with velocity of 16.0m/sec. The maximum and mean load were discussed to compare crash performance. The members with various section shapes were analyzed and the flange location was changed. Also, spot weld points were added in the initial buckling region to investigate its effect. Final rectangular section model which has flanges at the center and reinforcement in initial buckling region showed high enhancement in crash performance.

• Journal of Auto-vehicle Safety Association
• /
• v.8 no.3
• /
• pp.33-38
• /
• 2016

Recently, development in vehicle safety could increase interest in children's safety in vehicle collisions. But the research of children safety in vehicle collisions is not being conducted as many as that of adult's. Especially the study for the vehicle crash was not much. This study focused on the comparison of child safety between test protocols to evaluate children's safety in crash test. Injuries of Q6 and Q10 dummy were evaluated using FFRB (Full frontal rigid barrier) test and 40% ODB (Offset deformable barrier) test with one model vehicle. Even though the limit number of test, the tendency of injury criteria of Q6 and Q10 dummy between the test protocols was not conformed but injury criteria of Q6 and Q10 were not same between FFRB and 40% ODB.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2007.04a
• /
• pp.613-618
• /
• 2007

The real vehicle crash experiment is the best way to evaluate the performance of a guardrail. However the experiment is very expensive because of high cost of vehicles and guardrail installation. Thus in this study, crash simulation of a vehicle against a steel guardrail is performed using LS-DYNA. There are many researches on the impact of a vehicle against a guardrail. However the friction between a vehicle and a guardrail is not considered, although it affects considerably the behavior of a guardrail. In this paper, the friction coefficient is applied to evaluate correctly the performance of a guardrail.

• Design & Manufacturing
• /
• v.14 no.4
• /
• pp.40-45
• /
• 2020

In a vehicle-to-vehicle accident, the impact posture, braking status, final stopping position, collision point and collision speed are important factors for accident reconstruction. In particular, the speed of collision is the most important issue. In this study, the collision speed and the final stopping position in the tunnel were estimated using PC-CRASH, a vehicle crash analysis program used for traffic accident analysis, and the final stopping position of the simulation and the final stopping position of the traffic accident report were compared. When the Pride speed was 0km/h or 30km/h and the Sorento speed was 100m/h, the simulation results and reports matched the final stopping positions and posture of the two vehicles. As a result of the simulation, it can be estimated that Pride was collided in an almost stationary state.

• Journal of Auto-vehicle Safety Association
• /
• v.14 no.4
• /
• pp.21-26
• /
• 2022

Commercial use of autonomous vehicles is to come soon. So far most of responsibility of the accident is on the human driver with conventional vehicles whereas that will be on the car OEM and transportation related organizations with autonomous vehicles, which asks car OEM's and government to do vast study of car crash in various conditions. Test protocols need amendment and to be newly enacted to reflect new findings from the study aforementioned. Rigid stationary barrier and moving or stationary deformable barrier as well as car to car test which is same as actual accident can be utilized to simulate the crash happening on the road. Among those 3 test methods, rigid stationary barrier is most economic and has good repeatability. Limitation as well as advantage of the rigid stationary barrier is studied through comparison between car to car crash and oblique rigid barrier crash.

• Journal of Auto-vehicle Safety Association
• /
• v.14 no.1
• /
• pp.62-67
• /
• 2022

This study is to construct the simple estimating model for the HIC15 of the driver dummy using the frontal impact test results. Test results of 9 vehicles of Hyundai Sonata from the MY2002~MY2020 USNCAP are utilized for constructing the linear regression model. The average accelerations extracted from the vehicle crash pulses are handled as the main factors. The average accelerations of 10 ms interval within 0~100 ms are calculated from the crash pulse data of 9 vehicles. The present estimating model of the HIC15 using the average accelerations of 10 ms interval in the 0~80 ms range shows good agreement with the tested value within 2.4% maximum error.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.14 no.6
• /
• pp.190-194
• /
• 2006

This research investigates vehicle structure acceleration and vehicle deformation with RCAR crash test. To investigate vehicle damage characteristics in an individual case, it is possible to RCAR low speed crash test. In this study, two tests were conducted to evaluate difference between RCAR new condition and RCAR old condition. A two large vehicles were subjected to a frontal crash test at a speed of 15km/h with an offset of 40% $10^{\circ}$ angle barrier and flat barrier. The results of the 15km/h with an offset of 40% $10^{\circ}$ angle barrier revealed high acceleration value on the vehicle structure and high repair cost compared to the RCAR 15km/h with an offset of 40% flat barrier. So in order to improve damage characteristics in low speed crash of vehicle structure and body component of the monocoque type passenger vehicles, the end of front side member and front back beam should be designed with optimum level and to supply the end of front side member as a partial condition approx 300mm.

• Journal of the Korean Society for Precision Engineering
• /
• v.17 no.4
• /
• pp.226-232
• /
• 2000

This paper develops a finite element model for studying the crashworthiness analysis of a mid-size truck. A simulation for a truck frontal crash to a rigid barrier using the model is performed with PAM-CRASH installed in super computer SP2. Full vehicle model is composed of 86467 shell elements, 165 beam elements and 98 bar elements, and 86769 nodes. The model uses four material model such as elastic, elastic-plastic(steel), rigid and elastic-plastic(rubber) material model which are in PAM-CRASH. Frame and suspension system are modeled with 28774 shell elements and 31412 nodes. Cab is modeled with 34680 shell elements and 57 beam elements, and 36254 nodes. Bumper is modeled with 2262 shell elements, and 2508 nodes. Axle, steering shaft, etc are modeled using beam or bar elements. Mounting parts are modeled using rigid bodies. Bodies are interconnected using nodal constrains or joint options. To verify the developed model, frontal crash test with 30mph velocity to a rigid barrier is carried out. In the crash test, vehicle pulse at lower part of b-pillar is measured, and deformed shapes of frame and driver seat area are photographed. Those measured vehicle pulse and photographed pictures are compared those from the simulation to verify the developed finite element model.

• KIPS Transactions on Computer and Communication Systems
• /
• v.2 no.9
• /
• pp.399-404
• /
• 2013

MSEC(Microsoft Security Engineering Center) performed fuzz testing Windows Vista with 350 million test cases for 14 months before launching it. They analyzed crashes resulted from the testing and developed crash analyzer !exploitable based on the data used to determine exploitability. In this paper, we describe how MS crash analyzer determines exploitability of crashes. Besides, we suggest an improvement to overcome the limitations found in the MS crash analyzer during the analysis.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.16 no.2
• /
• pp.106-113
• /
• 2008

The goal of crashworthiness is an optimized vehicle structure that can absorb the crash energy by controlled vehicle deformations while maintaining adequate space so that the residual crash energy can be managed by the restraint systems to minimize crash loads transfer to the vehicle occupants. Front side assembly is one of the most important energy absorbing components in relating to the crashworthiness design of vehicle. The structure and shape of the front side assemblies are different depending on auto-makers and size of vehicles. Thus, it is not easy to grab an insight on designer's intention when you glance at a new front side member without experiences. In this paper, we have performed the explicit nonlinear dynamic finite element analysis on the front side assembly of a passenger car to investigate the effect of thickness distribution of the front side assembly on the collapse shape, which is important in the aspect of controlling deformation to maintain adequate space, from the viewpoint of reverse engineering. To do this, we have performed crash FE analysis for the assembly by varying the thickness distribution of the assembly.