• Composites Research
• /
• 제12권4호
• /
• pp.62-70
• /
• 1999

건축 구조물의 재령이 증가함에 따른 손상은 구조물의 안전성 및 신뢰성 확보에 매우 심각한 문제이다. 최근에는 이렇게 손상을 입은 콘크리트 구조물의 보수 보강을 위해 탄소섬유시트가 광범위하게 사용되고 있지만 탄소섬유시트를 보강한 콘크리트의 파괴기구가 명확하게 규명되지 않았다. 따라서 본 연구에서는 탄소섬유시트를 보강한 콘크리트의 손상거동 및 미시적 파손기구를 이해하기 위해 4가지 경우의 시험편, 즉 순수한 콘크리트, 철근 보강 콘크리트, 탄소섬유시트 보강 콘크리트, 철근과 탄소섬유시트 보강 콘크리트 시험편에 대하여 3점 굽힘 시험을 실시하였다. 이러한 시험편들의 파손기구를 명확히 하기 위해 음향방출기법이 사용되었으며 균열 발생, 성장을 모니터링하기 위해 2차원 AE 발생원 위치추정 기법이 적용되었다.

• 한국철도학회논문집
• /
• 제11권6호
• /
• pp.524-529
• /
• 2008

도시철도 차륜에서 손상된 차륜은 주행 중의 승차감 악화 및 보수비용의 증가로 이어질 수 있기 때문에 차륜답면 특성 변화에 대한 평가는 대단히 중요하다. 본 연구에서는 비파괴적 표면검사법을 이용하여 차륜답면의 손상 평가를 실시하였으며 접촉위치, 주행거리, 제동방식에 따라 차륜답면의 특성을 평가하였다. 그 결과 접촉위치에 따라 차륜답면이 현저히 다른 손상 특성을 나타남을 보여주고 있다.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 추계학술대회논문집A
• /
• pp.186-191
• /
• 2001

Tensile residual stress happen by difference of coefficients of thermal expansion between fiber and matrix is one of the serious problems in metal matrix composite(MMC). In this study, TiNi alloy fiber was used to solve the problem of the tensile residual stress as the reinforced material. TiNi alloy fiber improves the tensile strength of composite by occurring compressive residual stress in matrix using shape memory effect of it. Pre-strain was added to generate compressive residual stress inside TiNi/A16061 shape memory alloy(SMA) composite. It was also evaluated the effect of compressive residual stress corresponding to pre-strains variation and volume fraction of TiNi alloy. AE technique was used to clarify the microscopic damage behavior at high temperature and the effect of pre-strain difference of TiNi/A16061 SMA composite. In addition, two dimensional AE source location technique was applied to inspect the crack initiation and propagation in composite.

• 대한조선학회논문집
• /
• 제40권3호
• /
• pp.54-60
• /
• 2003

Fatigue strength of offshore structures or ship structures is significantly decreased due to corrosive environment condition such as sea water and/or coal, crude oil of cargoes, compared to that of on shore structures. In corrosive environment, fatigue strength of structures also depends on characteristics of weld material heat affected zone(HAZ). In this research work, rotary bending fatigue tests of parent material and HAZ of TMCP steel were performed in order to investigate the initiation and propagation of cracks both in air and in NaCl solution. Comparison of fatigue strength In relation with the salinity of NaCl were carried out as well. According to the test results weld material or HAZ of TMCP steel showed higher fatigue strength than that of the parent material. The fatigue strength of TMCP steel decreases drastically in NaCl solution compared to that of in air environment. In particular, more reduced fatigue strength is observed in 1% NaCl solution than in 3% NaCl solution.

• 토지주택연구
• /
• 제11권2호
• /
• pp.95-104
• /
• 2020

This study aims to explore a purely mechanistic pavement analysis approach where viscoelasticity and fracture of asphalt mixtures are considered to accurately predict deformation and damage behavior of flexible pavements. To do so, the viscoelastic and fracture properties of designated pavement materials are obtained through experiments and a fully mechanistic damage analysis is carried out using a finite element method (FEM). While modeling crack development can be done in various ways, this study uses the cohesive zone approach, which is a well-known fracture mechanics approach to efficiently model crack initiation and propagation. Different pavement configurations and traffic loads are considered based on three main functional classes of roads suggested by FHWA i.e., arterial, collector and local. For each road type, three different material combinations for asphalt concrete (AC) and base layers are considered to study damage behavior of pavement. A concept of the approach is presented and a case study where three different material combinations for AC and base layers are considered is exemplified to investigate progressive damage behavior of pavements when mixture properties and layer configurations were altered. Overall, it can be concluded that mechanistic pavement modeling attempted in this study could differentiate the performance of pavement sections due to varying design inputs. The promising results, although limited yet to be considered a fully practical method, infer that a few mixture tests can be integrated with the finite element modeling of the mixture tests and subsequent structural modeling of pavements to better design mixtures and pavements in a purely mechanistic manner.

• 열처리공학회지
• /
• 제35권4호
• /
• pp.185-192
• /
• 2022

Variations in the microstructure and mechanical properties of API X70 steel processed by piping, electrical resistance welding (ERW), and post seam annealing (PSA) are investigated in this study. In the welding zone, some elongated pearlites are formed and grains coarsening occurs due to extra heat caused by the ERW and PSA processes. After the piping, the base metal shows continuous yielding behavior and a decrease in yield and impact strengths because mobile dislocation and back stress are introduced during the piping process. On the other hand, the ERW and PSA processes additionally decreased the impact strength of welding zone at room and low temperatures because some elongated pearlites easily act as crack initiation site and coarse ferrite grains facilitate crack propagation. As a result, the fracture surface of the welding zone specimen tested at low temperature revealed mostly cleavage fracture unlike the base metal specimen.

• Journal of Welding and Joining
• /
• 제31권6호
• /
• pp.50-57
• /
• 2013

Characterization of microstructures and cryogenic mechanical properties of electro beam (EB) welds between cast and forged Inconel 718 superalloys has been investigated. Optimal EBW condition was found in the beam current range of 36~39 mA with the constant travel speed of 12 mm/s and arc voltage of 120 kV for 10 mm-thick specimens. Electron beam current lower than 25 mA caused to occur the liquation microfissuring in cast-side heat affected zone (HAZ) of EB welds. The HAZ liquation microfissure was found on the liquated grain boundaries with resolidified ${\gamma}/Laves$ and ${\gamma}/NbC$ eutectic constituents. EBW produced welds showing a fine dendritic structure with relatively discrete Laves phase due to fast cooling rate. After post weld aging treatment, blocky Laves phase and formation of ${\gamma}^{\prime}+{\gamma}^{{\prime}{\prime}}$ strengtheners were observed. Presence of primary strengthener and coarse Laves particles in PWHT weld may cause to reduce micro-plastic zone ahead of a crack, leading to a significant decrease in Charpy impact toughness at $-196^{\circ}C$. Fracture initiation and propagation induced by Charpy impact testing were discussed in terms of the dislocation structures ahead of crack arisen from the fractured Laves phase.

• 한국전산구조공학회논문집
• /
• 제30권2호
• /
• pp.145-151
• /
• 2017

콘크리트 구조물 또는 암석의 해체 공정에서 소음, 진동, 분진 등의 발생을 초래하는 기존의 발파공법을 대신하여 비폭성 파쇄제의 이용을 고려할 수 있다. 본 연구는 유한한 정사각형 콘크리트 구조물을 대상으로 하여 비폭성 파쇄제의 팽창이 준정적으로 균열을 발생, 진전시키는 과정을 유한요소해석으로 예측하고 기존 문헌에 보고된 실험결과와 비교함으로써 해석결과의 정확성을 검증하였다. 또한 비폭성 파쇄제 및 천공 홀의 배치에 따른 영향을 최소요구팽창압 관점에서 분석하였다. 더 나아가서 비폭성 파쇄제가 채워지지 않은 천공 홀이 비폭성 파쇄 공정에 미치는 영향을 분석하고, 분리 조각의 수를 증가시켜 파쇄도를 향상시키기 위한 비폭성 파쇄제 및 천공 홀의 효과적인 배치에 대하여 고찰하였다.

• Geomechanics and Engineering
• /
• 제14권3호
• /
• pp.271-281
• /
• 2018

A jointed rock slope stability evaluation was simulated by a discontinuous deformation analysis numerical method to investigate the process and safety factors for different crack distributions and different overloading situations. An optimized method using Discontinuous Deformation Analysis for Rock Failure (DDARF) is presented to perform numerical investigations on the jointed rock slope stability evaluation of the Dagangshan hydropower station. During the pre-processing of establishing the numerical model, an integrated software system including AutoCAD, Screen Capture, and Excel is adopted to facilitate the implementation of the numerical model with random joint network. These optimizations during the pre-processing stage of DDARF can remarkably improve the simulation efficiency, making it possible for complex model calculation. In the numerical investigations on the jointed rock slope stability evaluations using the optimized DDARF, three calculation schemes have been taken into account in the numerical model: (I) no joint; (II) two sets of regular parallel joints; and (III) multiple sets of random joints. This model is capable of replicating the entire processes including crack initiation, propagation, formation of shear zones, and local failures, and thus is able to provide constructive suggestions to supporting schemes for the slope. Meanwhile, the overloading numerical simulations under the same three schemes have also been performed. Overloading safety factors of the three schemes are 5.68, 2.42 and 1.39, respectively, which are obtained by analyzing the displacement evolutions of key monitoring points during overloading.

• 풍력에너지저널
• /
• 제14권3호
• /
• pp.83-90
• /
• 2023

The purpose of this study is to evaluate the inter-laminar fracture toughness characteristics of CFRP pultrusion spar cap materials reinforced with non-woven glass fabric. Test specimens were fabricated by the infusion technique. A non-woven glass fabric and artificial defects were embedded on the middle surface between two pultruded CFRP panels. Double cantilever beam (DCB) and End Notched Flexure (ENF) tests were performed according to ASTM standards. Fracture toughness and crack propagation characteristics were evaluated with load-displacement curves and delamination resistance curves (R-Curve). The fracture toughness results were calculated by compliance calibration (CC) method. The initiation and propagation values of Mode-I critical strain energy release rate value G_Ic were 1.357 kJ/m2 and 1.397 kJ/m2, respectively, and Mode-II critical strain energy release rate values G_IIc were 4.053 kJ/m2 for non-precracked test and 4.547 kJ/m2 for precracked test. It was found that the fracture toughness properties of the CFRP pultrusion spar-cap are influenced by the interface between the layers of CFRP and glass fiber non-woven.