• Journal of the Korean Ceramic Society
• /
• v.54 no.6
• /
• pp.511-517
• /
• 2017

With different working pressures and substrate biases, Cr-Al-N coatings were deposited by hybrid physical vapor deposition (PVD) method, consisting of unbalanced magnetron (UBM) sputtering and arc ion plating (AIP) processes. Cr and Al targets were used for the arc ion plating and the sputtering process, respectively. Phase analysis, and composition, binding energy, and microstructural analyses were performed using X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), and field emission scanning electron microscopy (FESEM), respectively. Surface droplet size of Cr-Al-N coatings was found to decrease with increasing substrate bias. A decrease of the deposition rate of Cr-Al-N films was expected due to the increase of substrate bias. The coatings were grown with textured CrN phase and (111), (200), and (220) planes. X-ray diffraction data show that all Cr-Al-N coatings shifted to lower diffraction angles due to the addition of Al. The XPS results were used to determine the $Cr_2N$, CrN, and (Cr,Al)N binding energies. The compositions of the Cr-Al-N films were measured by XPS to be Cr 23.2~36.9 at%, Al 30.1~40.3 at%, and N 31.3~38.6 at%.

• Corrosion Science and Technology
• /
• v.2 no.6
• /
• pp.289-295
• /
• 2003

The corrosion behavior of Cr-N coated steels with different phases (${\alpha}-Cr$, CrN and $Cr_2N$) deposited by cathodic arc deposition on Hl3 steel was investigated in 3.5% NaCl solution at ambient temperature. Potentiodynamic polarization test, electrochemical impedance spectroscopy (EIS) and scanning electron microscopy (SEM) were the techniques applied to characterize the corrosion behavior. It was found that the CrN coating had a lower current density from potentiodynamic polarization test than others. The porosity, corresponding to the ratio of the polarization resistance of the uncoated and the coated substrate, was higher in the $Cr_2N$ coating than in the other Cr-N coated steels. EIS measurements showed, for the most of Cr-N coated steels, that the Bode plot presented two time constants. Also, the $Cr_2N$ coating represents the characteristic of Warburg behavior after 72hr of immersion. The coating morphologies were examined in planar view and cross-section by SEM analyses and the results were compared with those of the electrochemical measurement. The CrN coating had a dense, columnar grain-sized microstructure with minor intergranular porosity. From the above results, the CrN coating provided a better corrosion protection than the other Cr-N coated steels.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2007.11a
• /
• pp.130-131
• /
• 2007

초고경도 박막을 얻기 위해 질화물을 이용한 CrN / CrAlN 초격자 박막을 CFUBM 시스템을 통해 합성하였다. 초격자 박막의 각층의 두께 (${\lambda}$)는 기판의 회전 속도를 이용하여 제어하여 4.4 에서 44.1 nm 까지 합성하였다. 박막의 결정구조 및 미세구조를 분석하기 위하여 고분해능 X선 회절 분석기 (HR-XRD)를 이용하였으며, 박막의 기계적 성질은 나노 인덴터와 ball on disk tester를 통해 분석하였다. CrN / CrAlN 초격자 박막은 각층의 두께 (${\lambda}$)에 따라 28.77 GPa에서 31.97 GPa의 경도 값을 나타내었으며, 미세구조와 기계적 특성이 변화를 관찰할 수 있었다.

• Journal of the Korean institute of surface engineering
• /
• v.44 no.6
• /
• pp.269-276
• /
• 2011

Phase evolution and tribological behavior of Cr-Mo-N multi compositional films with different interlayer were investigated. The films were deposited by hybrid PVD (Physical Vapor Deposition) system consisted of dc unbalanced magnetron (UBM) sputtering and arc ion plating (AIP) sources. A pure molybdenum (Mo) was used as sputtering target and also a pure Cr was used as AIP target to form the Cr-Mo-N films. Various growth planes were found, no textured surface, in all of the multi composition films. Maximum value of microhardness was measured in Cr-Mo-N film with Mo interlayer as 29 GPa. Composition film was mainly showed the aspect of the adhesive wear than CrN film. The friction coefficient was decreased from 0.6 for pure CrN coating to 0.35 for Cr-Mo-N film with Mo interlayer. This result may come from the formation of metal oxide tribo-layer which is known as solid lubricant during the wear test.

• Proceedings of the KIEE Conference
• /
• 2001.07c
• /
• pp.1399-1401
• /
• 2001

We studied on structure and resistivity, temperature coefficient of resistance (TCR) of NiCr and NiCr-N thin resistor films prepared by do reactive magnetron sputtering of NiCr target. It is found that while pure NiCr films are polycrystalline, an addition of nitrogen (N2/(Ar+N2) ratios are between 10% and 70%) into the film is changed into amorphous structure and sheet resistance of films is increased. Measurement temperatures of TCR are ratios of $5^{\circ}C$ per 15min from $25^{\circ}C$ to $130^{\circ}C$. TCR for an as-deposited NiCr-N thin film is varied from positive to negative.

• Journal of the Korean institute of surface engineering
• /
• v.38 no.6
• /
• pp.207-211
• /
• 2005

In this work a multi-layered nanostructured TiAIN/CrN superlattice coatings was synthesized using closed-field unbalanced magnetron sputtering method and the relationships between their superlattice period (1), micro-structure, hardness and elastic modulus were investigated. In addition, wear test at $500^{\circ}C$ and oxidation resistance test at $900^{\circ}C$ were performed to investigate high temperature properties of these thin films. The coatings were characterized in terms of microstructure and mechanical properties by transmission electron microscopy (TEM) and nano-indentation test. Results from TEM analysis showed that superlattice periods was inversely proportional to the jig rotation speed. The maximum hardness and elastic modulus of 37 GPa and 375 GPa were observed at superalttice period of 6.1 nm and 4.4 nm, respectively. An higher value of microhardness from TiAIN/CrN thin films than either TiAIN (30 GPa) or CrN (26 GPa) was noted while the elastic modulus was approximately an average of TiAIN and CrN films. These enhancement effects in superlattice films could be attributed to the resistance to dislocation glide across interface between the CrN and TiAIN layers. Much improved plastic deformation resistance ($H^3/E^2$) of 0.36 from TiAIN/CrN coatings was observed, compared with 0.15 and 0.16 from TiAIN and CrN, respectively. Also the wear resistance at $500^{\circ}C$ was largely increased than those of single TiAIN and CrN coatings and TiAIN/CrN coatings showed much reduced weight gain after exposure at $900^{\circ}C$ for 20 hours.

• Korean Journal of Materials Research
• /
• v.14 no.8
• /
• pp.558-564
• /
• 2004

In order to improve the low hardness and low wear resistance of Ti-6Al-4V alloy, plasma carburization treatment and CrN film coating were carried out. Effects of the plasma carburization and CrN coating were analyzed and compared with the non-treated alloy by mechanical and creep tests. After plasma carburization and CrN coating treatments, the carburized layer was about 150 ${\mu}m$ in depth and CrN coated layer was about 7.5 ${\mu}m$ in thickness. Hardness value of about $H_{v}$ 402 of the non-treated alloy was improved to $H_{v}$ 1600 and 1390 by plasma carburization and CrN thin film coating, respectively. Stress exponent(n) was decreased from 9.10 in CrN coating specimen to 8.95 in carburized specimen. However, the activation energy(Q) was increased from 242 to 250 kJ/mol. It can be concluded that the static creep deformation for Ti-6Al-4V alloy is controlled by the dislocation climb over the ranges of the experimental conditions.

• Communications of the Korean Mathematical Society
• /
• v.16 no.2
• /
• pp.265-275
• /
• 2001

In the previous paper we studied n-dimensional CR-submanifolds of (n-1) CR-dimension immersed in a complex projective space CP(sup)(n+p)/2, and especially determined such submanifolds under curvature conditions related to vertical direction; In the present article we determine such submanifolds under curvature conditions related to horizontal directions.

• Bulletin of the Korean Mathematical Society
• /
• v.38 no.3
• /
• pp.575-586
• /
• 2001

The purpose of this paper is to study n-dimensional CR-submanifolds of (n-1) CR-dimension immersed in a complex projective space $CP^{(n+p)/2}$, and especially to determine such submanifolds under some curvature conditions.

• Communications of the Korean Mathematical Society
• /
• v.17 no.3
• /
• pp.519-529
• /
• 2002

In this paper. We Study (n + 1)-dimensional Contact CR-submanifolds of (n - 1) contact CR-dimension immersed in a Sasakian space form M$\^$2m+1/(c) (2m=n+p, p>0), and especially determine such submanifolds under additional condition concerning with shape operator.