• 한국방재학회 논문집
• /
• 제8권5호
• /
• pp.7-13
• /
• 2008

본 논문은 염해에 의한 부착성능 저하에 따른 철근-콘크리트 국부 비부착 구간 변화에 따른 보의 휨 실험 및 해석적 연구이다. RC보의 휨 실험 및 해석적 연구를 통하여 부착강도 및 부식정도에 대한 휨 강성을 평가, 분석하였다. 철근부식에 따른 국부적 부착손상 구간을 표현하기위하여 본 연구에서는 고무호스를 이용한 비부착 구간 모사 시험체를 제작, 염해에 의한 철근콘크리트 보의 국부 부식구간을 표현하였고 이에 대한 휨 성능을 평가하였다. 해석적 연구에서는 상용해석프로그램을 이용한 성능평가와 균열해석을 수행하여 국부적 부착구간 변화에 따른 균열 폭, 균열깊이, 위치를 파악함으로써 실제 실험결과와의 균열 확산을 예측, 비교하였다. 본 연구의 부식정도 및 국부적 비부착 구간 확대에 따른 실험적, 해석적 철근부식-강성변화율은 향후 노후 철근콘크리트 구조물의 국부적 손상 모델의 개발 및 평가에 있어 기초자료로 활용될 수 있을 것이다.

• 설비공학논문집
• /
• 제3권4호
• /
• pp.256-262
• /
• 1991

The corrosion effects on thermal contact resistance were experimentally studied for a given contact interface of a couple of metals. 2 cylindrically shaped test pieces, the one was carbon steel whose surface was machined by lathe and the other was stainless steel, ground, were come into contact under pressure, and then submerged to $HNO_3$ gas environment. While the corrosion process was going on, the thermal contact resistance was measured with time. The experiment was performed for 2 cases; 1) Highly compress the test pieces and then bring them to $HNO_3$ gas environment. 2) Anteriorly corrode the interface under low contact pressure and then increase the contact pressure. The results were as follows; In 1st. case of experiment, the thermal contact resistance seemed to be very stable, and showed low values with a tendancy of small decrease with time. But in 2nd. case the resistance was unstable and jumped to a value of 200-250% more then that expected for uncontaminated interface. More over it demonstrated some increase with time.

• 한국구조물진단유지관리공학회 논문집
• /
• 제27권1호
• /
• pp.54-63
• /
• 2023

본 논문에서는 부식된 철근과 콘크리트 계면의 부착강도-슬립거동에 있어 부식수준 및 균열폭의 영향에 대한 연구를 수행하였다. 기존의 연구는 주로 부식수준에 따른 부착강도 저하에 초점을 맞추고 있으나 부식에 의한 콘크리트 표면 균열폭에 따른 부착강도 저하에 관한 연구는 매우 적다. 따라서 본 연구에서는 부식된 철근과 콘크리트 접합부의 부착강도, 슬립 거동 및 철근의 질량손실 등을 평가하고 균열폭 대비 접합성능을 확인하기 인발시험을 실시하였다. 그 결과로 표면 균열폭에 따른 접착강도 저하의 경향성이 부식수준에 따른 경향성보다 균등하게 나타났다. 따라서 부식수준에 비해 콘크리트 표면 균열 발생 여부가 부착강도-슬립거동 관계의 성능저하를 판단하기에 적합한 것으로 판단된다.

• 한국재료학회지
• /
• 제9권2호
• /
• pp.205-210
• /
• 1999

The 250ppm hydrogen-charged Zircaloy-4 sheets, homogenized at $400^{\circ}C$ for 72hrs in vacuum, were corroded under the autoclave conditions of $350^{\circ}C$, 2350psi. The corrosion behavior of the Zircaloy-4 sheets was evaluated by measuring their weight gains with the exposure time. The electrical characteristics were investigated in the ranges of 5000~1x10\ulcornerHz using AC impedance technique in 1N $H_2$$SO_4$aqueous solution. The corrosion rate of the hydrogen charged specimen was more rapid than the normal specimen at the early stage of the corrosion. With a longer corrosion time, however, the normal specimen corroded faster than the hydrogen-charged specimen. At the same time the hydrogen pickup in the hydrogen-charged specimen was more suppressed compared with the normal specimen. Such appears to be occurred because the impedance for the movement of the hydrogen ion into the metal was higher in the hydrogen-charged specimen compared to normal specimen at the interface between the oxide layer and the uncorroded metal. Thus the corrosion rate of the hydrogen-charged specimen was likely to be decreased with a longer corrosion time.

• 대한금속재료학회지
• /
• 제50권3호
• /
• pp.218-223
• /
• 2012

Fe-(8.5, 18.5, 28.3, 36.9) wt% Cr alloys were corroded between 600 and $800^{\circ}C$ for up to 70 h in a 1 atm gas mixture that consisted of 0.0242 atm of $H_2S$, 0.031 atm of water vapor, and 0.9448 atm of nitrogen gas. Their corrosion resistance increased with an increment in the Cr content. The Fe-8.5%Cr alloy corroded fast, forming thick, fragile, nonadherent scales that consisted primarily of an outer FeS layer and an inner (Fe, Cr, O, S)-mixed layer. The outer FeS layer grew into the air by the outward diffusion of $Fe^{2+}$ ions, whereas the inner mixed layer grew by the inward diffusion of oxygen and sulfur ions. At the interface of the outer and inner scales, voids developed and cracking occurred. The Fe-(18.5, 28.3, 36.9)% Cr alloys displayed much better corrosion resistance than the Fe-8.5Cr alloy, because thin $Cr_2O_3$ or $Cr_2S_3$ scales formed.

• Structural Engineering and Mechanics
• /
• 제41권5호
• /
• pp.645-662
• /
• 2012

Deteriorative effects of steel corrosion on the structural response of reinforced concrete are simulated for varying degrees of corrosion. The simulation approach is based on a three-dimensional irregular lattice model of the bulk concrete, in which fracture is modeled using a crack band approach that conserves fracture energy. Frame elements and bond link elements represent the reinforcing steel and its interface with the concrete, respectively. Polylinear stress-slip properties of the link elements are determined, for several degrees of corrosion, through comparisons with direct pullout tests reported in the literature. The link properties are then used for the lattice modeling of reinforced concrete beams with similar degrees of corrosion of the main reinforcing steel. The model is successful in simulating several important effects of steel corrosion, including increased deflections, changes in flexural cracking behavior, and reduced yield load of the beam specimens.

• 한국세라믹학회지
• /
• 제28권8호
• /
• pp.626-634
• /
• 1991

The specimens for the corrosion test were made by hot-pressing of SiC power with 2 wt% Nl2O3 and 10wt% Al2O3 additions at 200$0^{\circ}C$ and 205$0^{\circ}C$. The specimens were corroded in 37 mole% NaCl and 63 mole% Na2SO4 salt mixture at 100$0^{\circ}C$ up to 60 min. SiO2 layer was formed on SiC and then this oxide layer was dissolved by Na2O ion in the salt mixture. The rate of corrosion of the specimen containing 10 wt% Al2O3 was slower than that of the specimen containing 2 wt% Al2O3. This is due to the presence of continuous grain boundary phase in the specimen containing 10 wt% Al2O3. The oxidation of SiC produced gas bubbles at the SiC-SiO2 interface. The rate of corrosion follows a linear rate law up to 50 min. and then was accelerated. This acceleration is due to the disruption oxide layer by the gas evolution at SiC-SiO2 interface. Pitting corrosion has found at open pores and grain boundaries.

• 한국산학기술학회논문지
• /
• 제15권5호
• /
• pp.3251-3259
• /
• 2014

본 논문에서는 철근의 부식을 고려한 철근콘크리트(RC)보의 휨파괴거동을 규명하기 위하여 수행한 일련의 3점휨 파괴시험 및 해석적 연구 결과를 제시하였다. 실험적 연구를 위하여 총12개의 시편보를 제작하였으며, 염수분무시험 챔버를 이용하여 10개월간 촉진부식토록 하였다. 철근부식에 미치는 균열의 영향을 분석하기 위하여 일부 시험체를 공칭휨강도의 30% 와 60%에 해당하는 최대하중으로 미리 하중을 가한 후 염소분무 시험챔버에 보관하였다. 재령 5개월 및 10월에 각각 휨파괴시험을 실시하였으며 최대하중과 하중-처짐곡선을 측정하였다. 실험결과 철근의 부식정도에 따라 철근과 콘크리트간의 부착력 손실이 발생하고 그에 기인하여 휨강도는 최대 5.4%, 연성도는 최대 43%의 저하가 발생하여 철근의 부식이 최대 하중 보다 연성도에 미치는 영향이 큰 것으로 나타났다. 한편, Maaddawy의 해석적 모델을 이용한 수치해석결과 철근의 부식을 고려한 RC보의 휨파괴거동을 상당부분 잘 묘사할 수 있는 것으로 나타났다.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2002년도 봄 학술발표회 논문집
• /
• pp.361-366
• /
• 2002

The deterioration of concrete structure due to corrosion of the reinforcement has created big financial losses on the overall industries. The volume expansion of the corrosion products causes internal pressure to concrete wall around reinforcing bar. If the maximum principal stress induced by internal pressure exceeds the tensile strength of the concrete at any point of time, a crack forms at any point of material. Therefore, in terms of life assessment of concrete structure, it is very important to predict the amount of corrosion products which induces initial concrete cracking. With this objective, this paper proposes the critical amount of corrosion products at interface between reinforcement and concrete using finite element analysis. If an actual survey of corrosion rates could be made, the model might supply information for condition assessment of existing concrete structure. As the mechanical properties of corrosion product and instantaneous geometry of corroded steel are considered in the analysis, the value obtained will be more realistic.

• 비파괴검사학회지
• /
• 제25권3호
• /
• pp.157-162
• /
• 2005

In order to evaluate the corrosion of reinforcing steel-bars (rebar) in concrete, a nondestructive evaluation by the half-cell potential method is currently applied. In this study, potentials measured on a concrete surface are compensated into those on the concrete-rebar interface by the inverse boundary element method (IBEM). Because these potentials are obtained three-dimensionally (3-D), 3-D visualization is desirable. To this end, a visualization system has been developed by using VRML (Virtual Reality Modeling Language). As an application, results of a reinforced concrete (RC) slab with corroded rebars are visualized and discussed.