• Bulletin of the Korean Chemical Society
• /
• v.33 no.11
• /
• pp.3745-3748
• /
• 2012

This study presents a rapid and simple ${\alpha}$ source preparation method for a radioactive waste sample. The recovery of $^{239}Pu$, $^{232}U$ and $^{243}Am$ using a micro-coprecipitation method was over 95%. The ${\alpha}$-peak resolution of Pu and Am isotopes through the micro-coprecipitation method is enough to discriminate the Pu and Am isotopes from other Pu and Am isotopes. The determination of the Pu and Am isotopes using the micro-coprecipitation method was applied to the radioactive waste sample, so that the activity concentrations of the Pu and Am isotopes using the micro-coprecipitation method in the radioactive waste sample were similar to those using the electrodeposition method.

• Journal of the Korean Ceramic Society
• /
• v.30 no.10
• /
• pp.829-837
• /
• 1993

Chemically and geometrically homogeneous mixing of Si3N4 powders with sintering additives(YAG, 3Y2O3$.$5Al2O3) was attempted via coprecipitation method. X-ray dot maps for the additive elements(Al and Y) showed that the additives are evenly distributed in the powder mixture prepared by coprecipitation method(CP). TEM observation of the coprecipittion-treated Si3N4 powders revealed that they are covered with extremely fine crystallites of additive. The shift in isoelectric point(IEP) of Si3N4 powders from pH 6.7 to pH 7.9 after coprecipitation mixing gave another evidence for coating of Si3N4 powders with YAG additives. SIMS analysis for composition on the surface and in the matrix of mixed powders showed that the YAG additives are highly enriched on the surface of coprecipitation-treated Si3N4 powders. Especially when a small amount of additive was used, the effect of homogeneous additive distribution on densification was preceptible: After pressureless-sintering of powder compacts containing 5 mol% YAG at 1800$^{\circ}C$ for 0.5h, a sintered density of 96.5% theoretical was obtained from the specimens prepared bycoprecipitation in comparison with 93.8% from the mechanically-mixed one.

• Journal of the Korean Ceramic Society
• /
• v.25 no.2
• /
• pp.168-172
• /
• 1988

In order to prevent the PbO vaporization during calcination and to produce the powder of good sinterability, a coprecipitation method for preparing homogeneous Lead-Zirconate-Titanate (PZT) powder from aqueous salt solution is described. In this method, the PZT-ceramics show low calcining and sintering temperature, and they have good sintering and electronic properties.

• Analytical Science and Technology
• /
• v.19 no.4
• /
• pp.280-284
• /
• 2006

The objective of this study is to investigate the removal of heavy metal by using the coprecipitation of barium sulfate. Several parameters governing the efficiency of the coprecipitation method were evaluated by the pH of sample solution, amount of coprecipitant, and addition of sulfide for the removal of As(V), Cd(II), Cr(III), Cr(VI), Cu(II), Hg(II) and Pb(II) metal ions ($10{\mu}g/ml$ each). The coprecipitation was about 80% - 95% only for lead at low pH but under 10% for other ions. The amount of removal was about 95% - 100% for Cd, Hg, Pb, Cu in the all pH range by the addition of sulfide with barium sulfate but As(V) and Cr(III, VI) ions were not affected by the same conditions.

• Archives of Pharmacal Research
• /
• v.18 no.1
• /
• pp.22-26
• /
• 1995

The solubility and dissolution rate of naproxen (NPX) complexed with 2-hydroxypropyl-.betha.-cyc-lodextrin (2-HP.betha.CD) using coprecipitation, evaporation, freeze-drying and kneading method were investigated. Solubility of NPX linearly increased (correlation cefficient, 0.995) as $2-HP\betaCD$ concentraction increased, resutling in $A_l$ type phase solubility curve. Inclusion complexes prepared by four different methods were compared by different methods were compared by dfferential scanning calorimetry(DSC). The NPX showed sharp endothemic peak around $156^{\circ}C$ but inclusion complexes by evaporation, freeze-drying and kneading method showed very broad peak without distinct phase transtion temperature. In contrast, inclusion complex prepared by coprecipitation method resulted in detectable peak around $156^{\circ}C$ which is similar to NPX, suggesting incoplete formation of indusion co plex. Dissolution rate of inclusion complexes prepared by evaporation, frezz-drying and kneding except coprecipitation method was largely enhanced in the simultaed gastric and intestinal fluid when compared to NPX powder and commercial $NA-XEN^\registered$tablet. However, about 65% of NPX in gstric fluid. in case of inclusion complex prepared by coprecipitation method, formation of inclusion complex appeared to be incoplete, resulting in no marked enhancement of dissolution rate. From these findings, inclusion complexes of poorly water-soluble NPX with $2-HP\betaCD$ were useful to increase soubility and dissolution rate, resting in enhancement of bioavailability and minimization of gastrointestinal toxicity of drug upon oral administration of inclusion complex.

• Journal of the Korean Ceramic Society
• /
• v.22 no.5
• /
• pp.17-22
• /
• 1985

This study was to make powder by coprecipitation method and spray dispersion precipitation method in $(1-x)ZrO_2-xMgO$ system to improve sinterability. As the result the specific surface area of powder prepared by spray dispersion precipitation method and coprecipitation method was above $110m^2/g$ and $10-20m^2/g$ respectively. Spray dispersion precipitation method was more effective than coprecipitation method in powder preparation.

• Analytical Science and Technology
• /
• v.6 no.2
• /
• pp.207-215
• /
• 1993

$Si_3N_4$ powders were mixed with sintering additives($3Y_2O_3{\cdot}5Al_2O_3$, YAG) by coprecipitation method. Mixing homogeneity, sintered and mechanical properties of coprecipitation-mixed powder compacts were compared with those of mechanically-mixed ones. SIMS-analysis for composition on the surface and in the matrix of prepared powder mixtures showed that the added YAG exists mainly on the $Si_3N_4$ powder surfaces in a form of coating. From this result it could be concluded that coprecipitation method is superior to mechanical mixing in the mixing homogeneity. This mixing homogeneity can accompany an improvement in sintered density, microstructure and consequently the mechanical properties of sintered bodys.

• Proceedings of the KIEE Conference
• /
• 1991.07a
• /
• pp.213-216
• /
• 1991

In this study, PZT powder was synthesized by coprecipitation method us ing $Pb(NO_3)2$, $ZrOCl_2{\cdot}8H_2O$ and $TiCl_4$ as starting raw materials. Homogeneous and fine-grained PZT powder was obtained by the coprecipitation method. PZT powder was characterized by DTA, SEM and XRD analysis. The XRD peaks were observed at $600(^{\circ}C)$ and over.

• Journal of the Korean Ceramic Society
• /
• v.34 no.10
• /
• pp.1045-1052
• /
• 1997

Barium ferrites (BaFe12O19) were synthesized at the various temperature by the coprecipitation-oxidation method. X-ray diffraction Rietveld analysis for barium ferrites were performed, their microstructures were observed and their magnetic properties were measured, in order to analyze the crystal structures and determine the optimal temperature of heat-treatment. The barium ferrite, its average particle size 80 nm, was formed at 600℃ through the hematite (α-Fe2O3), but the site occupations of the Fe's in tetrahedral and bipyramidal sites and of the Ba relatively low. Increasing the heating temperature, these occupations and the magnetization increased, and the crystal c-axis decreased. These changes were very small at the heat treatment of above 800℃, but the particles were rapidly grown. It is suggested that the optimal temperature of heat-treatment is 800℃, at which temperature crystal structure is relatively stable and the particles hardly ever grow.

• Journal of the Korean Ceramic Society
• /
• v.25 no.6
• /
• pp.671-676
• /
• 1988

Preparation of high purity ultrafine Ba2Ti9O20 powder was investigated by coprecipitation method. Formation of Ba2Ti9O20 powder from precipitate of coprecipitation takes place at 120$0^{\circ}C$, which is 20$0^{\circ}C$ lower than that from mechanical mixtures of BaCO3 and TiO2. This is apparently due to the nature of the compounds formed by the reaction of mixtures of aqueous solutions of BaCl2 and TiCl4 with an ammoniacal solution of ammonium carbonate and ammouium hydroxide. In this method, the Ba2Ti9O20 powders show low callcining and sintering temperature and it has good sintering and dielectric constant at room temperature.