• 한국세라믹학회지
• /
• 제13권2호
• /
• pp.8-16
• /
• 1976

The conductive transparent film is prepared by spraying thin salt solution. In stannic chloride solution as a base solution, various dopants such as Al, Co, Cu and Ni were dissolved respectively as a chloride state and then the films were made by spraying solutions on hot glass plates. The properties of them were compared with those of the stannic salt single component film. The films doped with copper oxide and nickle oxide were improved by decreasing their sheet resistivity and temperature coefficient of resistivity. In comparison with the sheet resistivity and temperature coefficient of resistivity of stannic oxide single component film, being 2.5 K ohm/$\textrm{cm}^2$ and -1650ppm/$^{\circ}C$ respectively, its values of the film containing 15 mol % of copper oxide and formed at 40$0^{\circ}C$ were 2.5K ohm/$\textrm{cm}^2$ and -920ppm/$^{\circ}C$ respectively. The film containing 15 mol % of nickel oxide and formed at 50$0^{\circ}C$ has shown its sheet resistivity and temperature coefficient 0.7 K ohm/$\textrm{cm}^2$ and -940ppm/$^{\circ}C$ respectively.

• 자원리싸이클링
• /
• 제9권1호
• /
• pp.70-75
• /
• 2000

산화제 제조시 초기 과정에서 $Fe_3O_4$ 가 피복되었고 2 단계에서는 $Fe_3O_4$ 보다 첨착능이 우수한 것으로 알려져 있는 $Fe_3O_4$가 생성되었다. 산화제 폐염삼 30g/l에 5Cu mg/l를 첨가하여 20분간 반응하였을 경우 구리이온 제거효율은 74.8%이었다. 연속실험에서 최종 배출수중의 구리농도가 1mg/l이하를 파괴점으로 보았을 때 파괴점 도달시간은 23시간이었고 흡착용량은 0.87$\cdot$Cu/g$\cdot$IOCS이었다.

• 한국세라믹학회지
• /
• 제54권5호
• /
• pp.438-442
• /
• 2017

This paper reports the facile synthesis of microlamella-structured porous copper (Cu)-oxide-based electrode and its potential application as an advanced anode material for lithium-ion batteries (LIBs). Nanowire-like Cu oxide, which is created by a simple thermal oxidation process, is radially and uniformly formed on the entire surface of Cu foam that has been fabricated using a combination of water-based slurry freezing and sintering (freeze casting). Compared to the Cu foil with a Cu oxide layer grown under the same processing conditions, the Cu foam anode with 63% porosity exhibits over twice as much capacity as the Cu foil (264.2 vs. 131.1 mAh/g at 0.2 C), confirming its potential for use as an anode electrode for LIBs.

• 한국분말재료학회지
• /
• 제12권6호
• /
• pp.441-446
• /
• 2005

The copper oxide nano powders were synthesized by levitational gas condensation (LGC) method, and were applied to catalyst to fabricate 3,4-dihydropyrimidin-2-(1H)-one. Processes of adsorption of Biginelli reaction reagents on the copper nanooxide surface $Cu_2O{\circ}CuO$ were studied by IR-spectroscopy. It was shown that benzaldehyde coordination, acetoacetic ether on the oxide surface is carried out with participation of carbonyl fragments, urea by N-H bonds which affects positively on the reagents reactivity.

• 반도체디스플레이기술학회지
• /
• 제19권2호
• /
• pp.55-59
• /
• 2020

Copper Oxide (CuO) films were deposited on the n-type silicon wafer by rf magnetron sputtering for heterojunction solar cells. And then the samples were treated as a function of the annealing temperature (300-600℃) in a vacuum. Their electrical, optical and structural properties of the fabricated heterojunction solar cells were then investigated and the power conversion efficiencies (PCE) of the fabricated p-type copper oxide/n-type Si heterojunction cells were measured using solar simulator. After being treated at temperature of 500℃, the solar cells with CuO film have PCE of 0.43%, Current density of 5.37mA/㎠, Fill Factor of 39.82%.

• 한국표면공학회지
• /
• 제34권2호
• /
• pp.142-150
• /
• 2001

Due to naturally formed copper oxides, the adhesion strength between copper and epoxy resin is often very poor. To improve the adhesion strength between copper and epoxy resin, Cu-based leadframe sheets were oxidized in a brown-oxide forming solution. Then the effect of brown-oxide formation on the adhesion strength of leadframe to epoxy molding compound (EMC) was studied using pull-out specimens. After the pull-out test, fracture surfaces were analyzed using SEM, AES and EDS to determine failure path. The results showed that the failure path lay over inside the CuO and inside the EMC irrespective of the pull strength.

• 한국표면공학회지
• /
• 제5권3호
• /
• pp.77-85
• /
• 1972

A method of preparation of synthetic ignorgaic coating on copper (patina) has been presented . An Eh--pH diagram was constructed for the present Cu-H2O-SO$_4$ system using the most recently available thermodynamic data. In the path of the patination at room temperature the general behaviour of copper in acidic copper sulfate solutions with potassium chlorate as an oxidizing agent appeared to follow those predictable in this Eh-pH diagram. In the presence 0.05 molar cupric sulfate at a temperature of about 28$^{\circ}C$ a green brochantite (CuSO$_4$$.$3Cu(OH)$_2$) layer was formed on copper sheet in 20 days. In a solution having an initial pH of 3.5 the development of a brochantite coating has been observed to take place in two stages. In the first, a layer of cuprous oxide formed on the copper at a relatively rapid rate. In the ensuing step the outer layer of cuptrite was oxidized at much slower rate to form brochantite. The syntetic coatings appeared to consist of crystal-lites of brochanitite growing perpendicular to the cuprose oxide surface. The outer tips of the -crystallites were reasily broken off and gave to the layer a rather chalky character. Underneath, at the brochantite Cu$_2$O interface, however, the green layers were firmely attached. The effect of reagent concentration , solution agitation , and moderate temperature increase were investigated to improve the quality of coating. So also in a qualitative way were the effect of light.

• Korean Chemical Engineering Research
• /
• 제59권4호
• /
• pp.632-638
• /
• 2021

반도체 공정에서 구리 배선 공정의 도입에 따라 플라즈마 식각에 의해 배선의 형성과정에서 구리 산화물, 불화물 및 불화탄소 등을 포함한 복합 잔류물을 형성하게 된다. 본 연구에서는 아민기(-NH₂)와 카르복실기(-COOH)를 갖는 성분으로 세정액을 제조하여 구리 배선 공정에서의 식각 잔류물 제거 특성을 분석하였다. 아민기를 포함한 세정액은 질소에 치환된 성분 및 탄소결합의 길이에 따라 세정효과에 차이를 보이며, 세정액의 pH가 증가함에 따라 구리 산화물의 식각 속도가 증가하는 경향성을 보였다. 아민기의 활성은 염기성 영역에서, 카르복실기의 활성은 산성 영역에서 이루어지며, 각각의 영역에서 구리 또는 구리 산화물과의 complex 형성을 통하여 세정공정이 진행되었다.

• Bulletin of the Korean Chemical Society
• /
• 제32권4호
• /
• pp.1331-1335
• /
• 2011

We report the results of the characterization of Cu oxide thin films deposited by radio frequency (r.f.) magnetron sputtering at different annealing temperatures. The deposited Cu oxide thin films were investigated by scanning electron microscopy, spectroscopic ellipsometry, X-ray diffraction, atomic force microscopy, Xray photoelectron spectroscopy, and contact angle measurements. The thickness of the films was about 180 nm and the monoclinic CuO phase was detected. The $CuO_2$ and $Cu(OH)_2$ phases were grown as amorphous phase and the ratio of the three phases were independent on the annealing temperature. The surface of Cu oxide films changed from hydrophilic to hydrophobic as the annealing temperature increased. This phenomenon is due to the increase of the surface roughness. The direct optical band gap was also obtained and laid in the range between 2.36 and 3.06 eV.

• Journal of Electrochemical Science and Technology
• /
• 제3권1호
• /
• pp.35-43
• /
• 2012

Highly ordered and perforated anodic aluminum oxide membranes were prepared by anodic oxidation and subsequent removal of the barrier layer. By using these homemade anodic aluminum oxide membranes as templates, metal selenide nanowires and nanotubes were synthesized. The structure and composition of these one-dimensional nanomaterials were studied by field emission scanning electron microscopy as well as transmission electron microscopy and energy dispersive X-ray spectroscopy. The growth process of metal selenide inside anodic aluminum oxide channel was traced by investigating the series of samples using scanning electron microscopy after reacting for different times. Straight and dense copper selenide and silver selenide nanowires with a uniform diameter were successfully prepared. In case of nickel selenide, nanotubes were preferentially formed. Phase and crystallinity of the nanostructured materials were also investigated.