• Composites Research
• /
• 제35권3호
• /
• pp.182-187
• /
• 2022

본 논문은 다층 PCB에 사용되는 프리프레그의 물성을 파악하여 제시한 두께 실험식을 통해 PCB의 두께를 예측하기 위한 연구를 수행하였다. 프리프레그는 물성과 동박 잔존율에 의해서 PCB 제작시 두께가 감소하기 때문에 두께 실험식을 통한 정확한 PCB의 두께 예측이 필요하다. 두께 실험식에 사용되는 프리프레그의 밀도를 파악하기 위해 질량 및 두께를 측정하여 밀도를 도출하였다. 이후 CCL을 제작하기 위해 프리프레그와 동박을 적층하여 핫 프레스기를 사용하였고 광학현미경과 마이크로미터를 사용하여 두께를 측정하였다. 또한 동박 잔존율에 따른 두께 변화를 측정하기 위해 회로밀도를 다르게 구성하여 8층 PCB를 설계하였고 두께 측정 결과와 두께 실험식으로 도출된 두께를 비교하여 두께 실험식을 검증하였다. 비교 결과 CCL의 경우 2.56%, 다층 PCB의 경우 4.48%의 오차를 보였고 이를 통해 두께실험식의 신뢰성을 확인하였다.

• Tribology and Lubricants
• /
• 제21권2호
• /
• pp.71-76
• /
• 2005

This paper compares of mechanical tensile properties of 6 kinds of copper foil. The beam lead made with copper foil. Different from other package type such as plastic package, Chip Size Package has a reliability problem in beam lead rather than solder joint in board level. A new tensile loading system was developed using voice-coil actuator. The new tensile loading system has a load cell with maximum capacity of 20 N and a non-contact position measuring system based on the principle of capacitance micrometry with 0.1nm resolution for displacement measurement. Strain was calculated from the measured displacement using FE analysis. The comparison of mechanical properties helps designer of package to choose copper for ensuring reliability of beam lead in early stage of semiconductor development.

• Bulletin of the Korean Chemical Society
• /
• 제31권8호
• /
• pp.2283-2288
• /
• 2010

Nanostructured copper compounds were grown by electrochemical anodization of copper foil in aqueous NaOH under varying conditions including electrolyte concentration, reaction temperature, current density, and reaction time. Their morphology and atomic composition were investigated by using SEM, TEM, XRD, EDS and XPS. At the conditions ([NaOH] = 1 M, $20^{\circ}C$, $2\;mA\;cm^{-2}$), wire-like orthorhombic $Cu(OH)_2$ nanobundles with an average width of 100 - 300 nm and length of $10\;{\mu}m$ were synthesized with the preferential [100] growth direction. Furthermore, when the concentration decreased to 0.5 M NaOH, the 1D nanobundle structure became narrower and longer without any change in compositions or crystalline structure. Side reaction pathways appeared to compete with the 1D nanostructure formation channels: the formation of CuO nanoleaves at $50^{\circ}C$ via the sequential dehydration of $Cu(OH)_2$, CuO/$Cu_2O$ aggregates in 4 M NaOH, and $Cu_2O$ nanoparticles and CuO nanosheets at lower current density.

• 대한기계학회논문집A
• /
• 제30권2호
• /
• pp.157-163
• /
• 2006

Our research dealt with micro fabrication using micro forming process. The goal of the research was to establish the limit of forming process concerning the size of forming material and formed shape. Flat-rolled ultra thin metallic foils of pure copper(3.0 and $1.0{\mu}m$ in thickness)and stainless steel($2.5{\mu}m$ in thickness) were used for forming material. We obtained the various shapes of micro channels as using designed forming process. $12-14{\mu}m$ wide and $9{\mu}m$ deep channels were made on $3.0{\mu}m$ thick foil and $6{\mu}m$ wide and $3{\mu}m$deep channels were made on $1.0{\mu}m$ thick foil. Si wafer die for forming was fabricated by using etching technique. And the relation of etching time and die dimension was investigated for fabricating precisely die groove. For the forming, die and metal foil were vacuum packed and the forming was conducted with a cold isostatic press. The formed channels were examined in terms of their dimension, surface qualities and potential for defects. Base on the examinations, formability of ultra thin metallic foil was also discussed. Finally, we compared the forming result with simulation. The result of research showed that metal forming technology is promising to produce micro parts.

• 한국재료학회지
• /
• 제16권5호
• /
• pp.297-301
• /
• 2006

Si/Mo multilayer anode consisting of active/inactive material was prepared using rf/dc magnetron sputtering. Molybdenum acts as a buffer against the volume change of the Silicon. Multilayer deposited on RT (reversible treatment) copper foil current collector to enhance adhesion between Silicon and copper foil. Deposited Silicon was identified as an amorphous. Amorphous has a relatively open structure than crystal structure, thus prevents the lattice expansion and has many diffusion paths of Li ion. When deposited time of Silicon and Molybdenum is 30 second and 2 second respectably, electrode has more capacity and good cycle stability. A 3000 nm thick multilayer was maintained 99% of the initial capacity (1624 $mAhg^{-1}$) after 100 cycles. As the increase of the multilayer thickness (4500 nm, 6000 nm), Si/Mo mutilayer anodes show aggravation cycle stability.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2005년도 추계학술발표대회 개요집
• /
• pp.213-215
• /
• 2005

• 한국세라믹학회지
• /
• 제54권5호
• /
• pp.438-442
• /
• 2017

This paper reports the facile synthesis of microlamella-structured porous copper (Cu)-oxide-based electrode and its potential application as an advanced anode material for lithium-ion batteries (LIBs). Nanowire-like Cu oxide, which is created by a simple thermal oxidation process, is radially and uniformly formed on the entire surface of Cu foam that has been fabricated using a combination of water-based slurry freezing and sintering (freeze casting). Compared to the Cu foil with a Cu oxide layer grown under the same processing conditions, the Cu foam anode with 63% porosity exhibits over twice as much capacity as the Cu foil (264.2 vs. 131.1 mAh/g at 0.2 C), confirming its potential for use as an anode electrode for LIBs.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2006년도 춘계학술대회
• /
• pp.166-169
• /
• 2006

We fabricated hexagonal copper sulfide $Cu_2S$ nanowires to obtain a larger contact area of $Cu_2S/CdS$ solar cell. Copper sulfide nanowires were grown on Cu foil at room temperature by gas-sol id reaction. The size, density and shape of nanowires seemed to be affected by the change or reaction time temperature, crystallographic orientation of Cu foil, and molar ratio of the mixed gas. We controled the length and the diameter of the nanowires and we obtained suitable nanowire arrays which has fitting size for uniform deposition with n-type CdS. CdS layer was deposited on the nanowire array by electrodeposition and it seemed to be uniform. The $Cu_2S/CdS$ nanowires/CdS junction showed diode characteristics, A large contact area is expected with the $Cu_2S/CdS$ nanowire structure as compared with the $Cu_2S/CdS$ thin film.

• 대한금속재료학회지
• /
• 제47권11호
• /
• pp.740-747
• /
• 2009

The purpose of this study is to identify the effect of electrolyte compositions on electrodeposited copper foil. First of all, the polyimide substrate was pretreated with plasma. Finally, copper foil was deposited on a Cu/Ni/Polyimide substrate using the electroplating technique. As the quantity of Cu increased, preferred orientations changed into (111). Increasing sulfuric acid, on the other hand, brought down the preferred orientation of (111). The lowest sheet resistance, surface roughness, and fine adhesion were detected when the ratio of $Cu^{2+}$ and $H_2SO_4$ is 50:50(g/l).

• 한국정보과학회논문지:컴퓨팅의 실제 및 레터
• /
• 제10권6호
• /
• pp.499-506
• /
• 2004

제안된 동판 표면 검사 시스템은 PC-기반으로 다중 스레드 기법과 다중 CPU를 이용해 동판 표면의 결함을 실시간으로 검사하는 시스템이다. 초고속 라인 스캔 카메라로 영상 취득 보드에 영상을 실시간으로 취득하여 처리할 때, 더블 버퍼링 방법으로 입출력과 처리가 동시에 수행되어 처리 속도를 높인다. 다중 스레드 기법에서는 시스템 자원 활용과 다중 스레드로 CPU의 사용을 최대화하여 실시간 처리하며, 다중 스레드 구조로도 실시간 처리가 어려운 경우에는 다중 CPU를 사용하여 이를 해결한다. 또한 동판 표면 영상에서 결함 검출하여 분류할 때, 실시간 처리를 만족시키기 위해서 결함영상의 공분산 행렬의 고유치 비율, 명암차 등의 연산으로 분류할 수 있는 방법을 제시한다. 결함의 검출은 조명 불균형에 대한 보상 처리가 적용된 다음 임계치에 의해 검출된다. 검출된 결함은 제안된 분류 방법으로 특징을 분석한 뒤 결함의 형태를 분류한다. 특징은 결함 너비와 고유치 비율, 명암차 등이 사용되었다. 제시된 방법을 검증하기 위해서 총 141개의 결함을 분류하는 실험이 진행되었고, 결과로는 89.4% 성공률을 보였다.