• Journal of Electrochemical Science and Technology
• /
• 제8권2호
• /
• pp.146-154
• /
• 2017

In this study, copper (II) oxide was prepared for use in a copper electroplating solution. Copper chloride powder and copper (II) oxide are widely used as raw materials for electroplating. Copper (II) oxide was synthesized in this study using a two-step chemical reaction. Herein, we developed a method for the preparation of copper (II) oxide without the use of sintering. In the first step, copper carbonate was prepared without sintering, and then copper (II) oxide was synthesized without sintering using sodium hydroxide. The optimum amount of sodium hydroxide used for this process was 120 g and the optimum reaction temperature was $120^{\circ}C$ regardless of the starting material.

• Journal of Electrochemical Science and Technology
• /
• 제11권1호
• /
• pp.60-67
• /
• 2020

In this study, copper (II) oxide powder for electroplating was prepared by recovering CuCl₂ from NaClO₃ type etching wastes via recovered non-sintering two step chemical reaction. In case of alkali copper carbonate [mCuCo₃·nCu(OH)₂], first reaction product, CuCo₃ is produced more than Cu(OH)₂ when the reaction molar ratio of sodium carbonate is low, since m is larger than n. As the reaction molar ratio of sodium carbonate increased, m is larger than n and Cu(OH)₂ was produced more than CuCO₃. In the case of m has same values as n, the optimum reaction mole ratio was 1.44 at the reaction temperature of 80℃ based on the theoretical copper content of 57.5 wt. %. The optimum amount of sodium hydroxide was 120 g at 80℃ for production of copper (II) oxide prepared by using basic copper carbonate product of first reaction. At this time, the yield of copper (II) oxide was 96.6 wt.%. Also, the chloride ion concentration was 9.7 mg/L. The properties of produced copper (II) oxide such as mean particle size, dissolution time for sulfuric acid, and repose angle were 19.5 mm, 64 second, and 34.8°, respectively. As a result of the hole filling test, it was found that the copper oxide (II) prepared with 120 g of sodium hydroxide, the optimum amount of basic hydroxide for copper carbonate, has a hole filling of 11.0 mm, which satisfies the general hole filling management range of 15 mm or less.

• 한국군사과학기술학회지
• /
• 제21권5호
• /
• pp.591-598
• /
• 2018

The reaction characteristics of aluminum-copper(II) oxide composites initiated by the electrostatic discharge were studied as changing the aluminum particle size. Three different sizes of aluminum particles with nano-size copper(II)-oxide particle were used in the study. These composites were manufactured by two methods i.e. a shock-gel method and a self-assembly method. The larger aluminum particle size was, the less sensitive and less violent these composites were based on the electrostatic test. On the analysis of high speed camera about ignition appearances and burning time, the burning speed was faster when aluminum particle size was smaller.

• 문화기술의 융합
• /
• 제9권6호
• /
• pp.855-859
• /
• 2023

질산구리삼수화물염(copper(II) nitrate trihydrate) 수용액을 공업용 전분(starch)에 함침 시킨 전구체를 이용하여 산화구리(CuO) 나노 입자를 합성하였다. 주사전자현미경(SEM)을 통하여 질산구리삼수화물염 수용액이 함침된 전구체에 대한 구조를 분석하였고, 전구체에 대한 열처리 온도를 증가 시킴에 따라 생성되는 산화구리 입자의 입자 크기와 결정 구조를 X선회절분석법(XRD)과 주사전자현미경(SEM)으로 분석하였다. 분석 결과에 따르면, 전구체에서 유기물질이 완전히 열분해 되어지는 온도는 450-490℃이며, 열처리하는 온도가 증가함에 따라 생성되는 산화구리 입자의 크기와 결정성이 증가하는 것을 확인할 수 있었고, 또한 500-800℃에서 1시간씩 열처리하여 얻은 산화구리 입자의 크기는 100nm-2㎛인 것으로 나타났다. 하소 온도 400℃에서 산화구리 결정상이 형성되고, 800℃까지는 산화구리 단일상만 존재하며, 하소 온도의 증가에 따라 생성되는 입자의 크기가 커지는 것을 확인하였다.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2014년도 제46회 동계 정기학술대회 초록집
• /
• pp.176.1-176.1
• /
• 2014

Graphene has attracted an increasing attention due to its extraordinary electronic, mechanical, and thermal properties. Especially, the two dimensional (2D) sheet of graphene with an extremely high surface to volume ratio has a great potential in the preparation of multifunctional nanomaterials, as 2D supports to host metal nanoparticles (NPs). Copper oxide is widely used in various areas as antifouling paint, p-type semiconductor, dry cell batteries, and catalysts. Although the copper oxide(II) has been well known for efficient catalyst in C-N cross-coupling reaction, copper oxide(I) has not been highlighted. In this research, CuO and Cu2O nanoparticles (NPs) dispersed on the surface of grapehene oxide (GO) have been synthesized by impregnation method and their morphological and electronic structures have been systemically investigated using TEM, XRD, and XAFS. We demonstrate that both CuO and Cu2O on graphene presents efficient catalytic performance toward C-N cross coupling reaction. The detailed structural difference between CuO and Cu2O NPs and their effect on catalytic performance are discussed.

• 한국전기전자재료학회논문지
• /
• 제16권7호
• /
• pp.622-626
• /
• 2003

We report the electrical properties of organic light emitting diodes (OLEDs) depending on the crystal structure of hole injection layer of copper(II)-phthalocyanine(CuPc) and the light irradiation the carrier mobility of copper(II)-phthalocyanine(CuPc) of light source. OLEDs were constructed with indium tin oxide(ITO)/CuPc/triphenyl-diamin(TPD)/tris-(8-hydroxyquinoline)aluminum(Alq$_3$)/Al.Photocurrent multiplication of OLEDs was varied by the heat-treatment condition of CuPc thin film and the light irradiation.

• Bulletin of the Korean Chemical Society
• /
• 제29권8호
• /
• pp.1561-1564
• /
• 2008

Although the use of Cu(II) salts as catalysts without reductants is limited in the cycloaddition of acetylenes with azides, the catalytic system employing average 10 nm CuO(II) nanoparticles in the absence of reductants shows good catalytic activity to form 1,4-disubstituted 1,2,3-triazoles even in wet THF as well as water. It is also noticeable that CuO(II) nanoparticle catalysts can be recycled with consistent activity. A range of alkynes and azides were subject to the optimized CuO(II) nanoparticle-catalyzed cycloaddition reaction conditions to afford the desired products in good yields.

• Carbon letters
• /
• 제11권2호
• /
• pp.117-121
• /
• 2010

The composites of alginate, carbon nanotube, and iron(III) oxide were prepared for the removal of heavy metal in aqueous pollutant. Both alginate and carbon nanotube were used as an adsorbent material and iron oxide was introduced for the easy recovery after removal of heavy metal to eliminate the secondary pollution. The morphology of composites was investigated by FE-SEM showing the carbon nanotubes coated with alginate and the iron oxide dispersed in the alginate matrix. The ferromagnetic properties of composites were shown by including iron(III) oxide additive. The copper ion removal was investigated with ICP AES. The copper ion removal efficiency increased greatly over 60% by using alginate-carbon nanotube composites.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2013년도 제44회 동계 정기학술대회 초록집
• /
• pp.453-453
• /
• 2013

유기 태양전지는 저비용으로 제작이 가능하고 제작이 용이한 장점을 가지고 있으므로 많은 그룹에서 관심을 가지고 있다. 정공 수송층으로 사용되는 PEDOT:PSS는 많이 사용되지만 강한 산성 특성 때문에 ITO 전극에 식각이 되므로 문제가 있다. 그러므로 산화물 반도체 $WO_3$, $MoO_3$, 그리고 $V_2O_3$ 등이 태양전지에 많이 만들어지고 있다. 특히 copper oxide는 높은 광흡수율을 가지고 있으므로 태양전지에 사용하는 데 많은 기대되는 물질이다. Copper oxide 박막은 열증착 법, 스프레이 필로시스, 전기화학 증착, 화학증착법, 그리고 솔-젤법 등 다양한 증착 방법이 있다. 넓은 면적의 소자를 제작할 경우 솔-젤 방법은 기존의 증착법에 비해 낮은 비용으로 제작, 높은 성장율, 그리고 높은 기계적 탄력성의 장점이 있다. 솔-젤법으로 만든 copper oxide는 P3HT의 HOMO (high occupied molecular orbital)와 비슷한 위치에 접하고 있으므로 정공수송층으로 적합하다. 본 연구에서 제작된 태양전지의 구조는 ITO/P3HT:PCBM/CuxO로 구성되어 있다. ITO가 $10{\Omega}$/sq의비저항을 가지고 있었고 UV 처리를 하였다. 그 위에 P3HT:PCBM (1:0.8 weight)를 스핀 코팅하였다. 마지막으로 0.1 M $Cu_xO$용액은 Cu (II) acetate monohydrate를 소스로 2-methoxyethanol ($C_3H_8O_2$)의 용제와 안정제로 monoethanolamine ($C_2H_7NO$)을 섞어서 만들었다. 그리고 P3HT:PCBM 위에 스핀 코팅하였고 열증착 방법으로 전극인 Ag 을 증착하여 최종 소자를 만들었다. Cu(II) acetate의 소스로 제작된 박막의 투과율 측정을 통해 에너지 밴드갭을 구할 수 있었다. Copper oxide 박막은 다결정구조 이므로 다중 밴드갭으로 구성되어지는 것을 알 수 있었다. 최종적으로 만들어진 소자를 열처리를 통해 소자 특성을 조사했더니 250도에서 가장 좋은 결과를 얻을 수 있었다.

• Journal of Electrochemical Science and Technology
• /
• 제2권4호
• /
• pp.204-210
• /
• 2011

Thin film electrodes have been intensively studied for active materials and current collectors to enhance the electrochemical performance. Here, porous structures of nickel-based oxide films, consisting of nickel oxide and copper (II) oxide, which was derived from the copper substrate during the annealing process, were deposited on metallic copper foils. The half-cell tests revealed excellent capacity retention after $80^{th}$ charge/discharge cycles. Some films showed an excess of the theoretical capacity of nickel oxides, which mainly originate from partially oxidized copper substrates during annealing. These results exhibit that both a preparation method of an active materials and partially oxidized current collectors could be important roles to apply thin film electrodes.