• 한국정밀공학회지
• /
• 제16권8호
• /
• pp.38-45
• /
• 1999

The 2-trowel type concrete floor finishing robot can move in any direction by adjusting the posture or trowels without any wheels. Since the quality of the smoothed and polished concrete floor is determined by plastering speed, we need to control the velocity of the robot. However, we cannot use the typical motion control method because it is very difficult to measure the velocity of the robot, in contrast to the mobile robots with wheels. To overcome this difficulty, the following are studied in this paper: we found that the robot dynamics has the disturbance depending on its translational speed, and showed that there exists the saturated velocity of the robot which is set by the posture of the trowels, and obtained the relationship between the saturated velocity and the posture in the translation. The result enables us to control the motion of the robot only by adjusting the posture of trowels without measuring the velocity of the robot. Currently, we built the troweling robot and are experimenting its performance with the proposed motion control method.

• 대한기계학회논문집A
• /
• 제25권1호
• /
• pp.135-144
• /
• 2001

In this study, the time varying boundary control using the right boundary transverse motion is suggested to stabilize the transverse vibration of an axially moving string on the basis of the energy flux between the moving string and the boundaries. The effectiveness of the active velocity boundary control is showed through the FDM simulation results. Sliding mode control is adopted in order to achieve velocity tracking control of the time varying right boundary to dissipate vibration energy of the string effectively. Optical sensor system for measuring the transverse vibration of an axially moving string is developed, and the angle of the incident wave to the right boundary, which is the input of the velocity boundary controller, is obtained. Experimental research is carried out to examine the validity and the performance of the transverse vibration control using the suggested velocity right boundary control scheme.

• 제어로봇시스템학회논문지
• /
• 제22권11호
• /
• pp.937-943
• /
• 2016

Vertical velocity is critical in many areas, such as the control of unmanned aerial vehicles, fall detection, and virtual reality. Conventionally, the integration of GPS (Global Positioning System) with an IMU (Inertial Measurement Unit) was popular for the estimation of vertical components. However, GPS cannot work well indoors and, more importantly, has low accuracy in the vertical direction. In order to overcome these issues, IMU-barometer integration has been suggested instead of IMU-GPS integration. This paper proposes a new complementary filter for the estimation of vertical velocity based on IMU-barometer integration. The proposed complementary filter is designed to minimize drift error in the estimated velocity by adding PID control in addition to a zero velocity update technique.

• International Journal of Control, Automation, and Systems
• /
• 제5권3호
• /
• pp.243-250
• /
• 2007

This paper presents a systematic method of estimating a velocity disturbance occurring in the fine seek control system of an optical disk drive. A fine seek loop gain adjustment algorithm is introduced to accurately estimate the velocity disturbance in spite of the uncertainties of the fine actuator. The velocity disturbance can be estimated from a measurable velocity, a fine seek controller output, and a compensated fine actuator model. A robust fine seek controller can be designed by considering a minimum fine seek open-loop gain, calculated by the estimated velocity disturbance. The proposed controller design method is applied to the fine seek control system of a DVD rewritable drive and is evaluated through the experimental results.

• 대한기계학회논문집A
• /
• 제21권2호
• /
• pp.297-304
• /
• 1997

This paper presents a systematic design method of an anti-swing control law for overhead cranes. A velocity servo system for the trolley of a crane is designed based on the dynamics of the trolley and its load. The velocity servo system compensates for the effects of load swing on the trolley dynamics so that the velocity servo is independent of load swing. The velocity servo system is used for the design of a position servo system for the trolley via the loop shaping method. The position servo system and the swing dynamics of the load are then used to design an angle control system for load swing based on the root locus method. The combined position servo and the angle control systems constitute the overall control system. In the presence of low frequency disturbances, the proposed control law guarantees accurate position control for the trolley and fast damping for load swing. Furthermore, the performance of the proposed control law is independent of the mass of the load. Experimental results on a prototype crane show the effectiveness of the proposed anti-swing control law.

• 한국산업보건학회지
• /
• 제3권2호
• /
• pp.204-212
• /
• 1993

This study was conducted to evaluate ventilation efficiency of 4-stage slot hood by variation of slot width, flow rate, hood size and baffle size. The slot velocity, control velocity and plenum velocity were related to slot width and the distance between source of contamination and hood. The results obtained from laboratory experiment for local exhaust ventilation systems were as follows ; 1. When slot widths were constant(equally changed) and the velocity was 6-10 m/s, the slot velocity from 1st slot to 4th slot gradually decreased. As the slot width-to-slot length ratio(WLR) decreased, the slot velocity of each stage increased. But if WLR value was less than 0.04, the slot velocity decreased. 2. When slot velocity exceeded 10 m/s with constant slot widths, the slot velocity of each stage was uniform. 3. When the slot velocity was uniform within 10 m/s and the first slot width was 14-20 mm, the slot width ratio between 1st slot and each of three other slots were 1, 1.25, 1.5 and 3.0, respectively. 4. The slot and plenum velocity were uniform when exhaust flow rate changed from 14 to $19m^3/min$ and there were no hood splitter vanes. 5. When the slot velocity at each stage was uniform, the control velocity at site 30 cm away from hood No.2 increased from 0.15-0.30 to 0.25-0.45 m/s and the control distance from 20 to 30 cm(about 1.5 times).

• 한국자동차공학회논문집
• /
• 제10권6호
• /
• pp.227-233
• /
• 2002

A vehicle longitudinal control strategy with guaranteed string stability for vehicle stop-and-go(SG) cruise control is presented in this paper. The SG cruise control systems should be designed such that string stability can be guaranteed in addition to that every vehicle in a string of SG cruise control vehicles must track any bounded acceleration and velocity profile of its preceding vehicle with a bounded spacing and velocity error. An optimal vehicle following control law based on the information of the 1311owing distance (clearance) and its velocity relative to the vehicle ahead (relative velocity) has been used and string stability analysis has been done based on the control law and constant time gap spacing policy, A validated multi-vehicle simulation package has been shown that the string stability analysis using the approximate model of the vehicle servo-loop which includes vehicle powertrain and brake control system dynamics is valid in the design of the SG cruise control law with guaranteed string stability.

• ETRI Journal
• /
• 제37권2호
• /
• pp.328-337
• /
• 2015

This paper applies acceleration/deceleration control-based velocity profiles to an infeed control algorithm for a cross-belt-type sorting system to improve the accuracy and performance of the system's infeed. The velocity profiles are of a trapezoidal shape and often have to be modified to ensure that parcels correctly synchronize with their intended carriers. Under the proposed method, an infeed line can handle up to 5,600 items/h, which indicates a 40% increase in performance in comparison with its existing handling rate of 4,000 items/h. This improvement in performance may lead to a reduction in the number of infeed lines required in a sorting system. The proposed infeed control algorithm is applied to a cross-belt-type sorting system (model name: SCS 1500) manufactured by Vanderlande Industries.

• 전자공학회논문지S
• /
• 제34S권11호
• /
• pp.63-72
• /
• 1997

The design and implementation of a drive wheel position, orientation, and velocity feedback control algorithm for a differential-drive mobile robot is described here. A new concept, the most significant error, is introduced as the control design objective. Drive wheel position, orientation, and velocity feedback control directly minimize the most siginificant error by coordinating the motion of the two drive wheels. The drive wheel position, orientation, and velocity feedback control algorithm is analyzed and experiments are conducted to evaluate its performance. The experimental results are shown that drive wheel position, orientation and velocity feedback control algorithm yields substantially smaller position and orientation errors than those of conventional methods.

• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제49권6호
• /
• pp.395-402
• /
• 2000

This paper presents the improvement for speed characteristics of a Brushless DC Motor (BLDCM), it was applied to digital PI control for this. The practical PID control has been widely used to velocity control of DC motors. In this paper, a digital PI controller is used in order to decrease the speed error in constant velocity control of BLDCM. A TMS320C31 DSP is used for the microprocessor of digital PI control. The method using the DSP carry out the real-time control. The DSP has the rapid calculation ability and sampling time used lms. Driving BLDCM used 50W, motor input DC 150V and rotation speed 3000rpm. When BLDCM is to approval for discretion velocity at the acceleration and deceleration driving with any load, it was a feasible for stabilization control. Therefore, the experimental results indicate the superiority and validity of the velocity control by digital PI control.