• 한국재료학회지
• /
• 제30권7호
• /
• pp.327-332
• /
• 2020

Laser induced surface activation (LISA) technology requires refined selection of process variables to fabricate conductive microcircuits on a general polymer material. Among the process variables, laser mode is one of the crucial factors to make a reliable conductor pattern. Here we compare the continuous wave (CW) laser mode with the pulse wave (PW) laser mode through determination of the surface roughness and circuit accuracy. In the CW laser mode, the surface roughness is pronounced during the implementation of the conductive circuit, which results in uneven plating. In the PW laser mode, the surface is relatively smooth and uniform, and the formed conductive circuit layer has few defects with excellent adhesion to the polymer material. As a result of a change of laser mode from CW to PW, the value of Ra of the polymer material decreases from 0.6 ㎛ to 0.2 ㎛; the value of Ra after the plating process decreases from 0.8 ㎛ to 0.4 ㎛, and a tight bonding force between the polymer source material and the conductive copper plating layer is achieved. In conclusion, this study shows that the PW laser process yields an excellent conductive circuit on a polymeric material.

• 대한의용생체공학회:의공학회지
• /
• 제37권4호
• /
• pp.134-139
• /
• 2016

US Food and Drug Administration (FDA) approved as a innovative cure for cancer, 1996. The effect is death of cancer cells through necrosis, apoptosis. Mainly the Continuous Wave mode (CW) use for PDT Laser. It sting, the question including itch, and etc. Reportedly, the increase of temperature with the perforated edema, ulcer, necrosis. The Thermal relaxation time and Oxygen recovery time is necessary. To give a normal oxygen recovery time of the cell, used Pulse mode. Progress, it was Burst Pulse mode when easing the thermal wake, the simplicity was secured, the PDT effect is good. Excepted in control group CW, Pulse, Burst pulse mode were incubated with various concentrations of 5-aminolevulinic acid hydrochloride (ALA-5). The tumor size reduction CW mode (44%), Pulse mode (48%), Burst pulse mode (53%) at 4 week after PDT with 0.3, 0.3, 0.3 mg/ml of ALA-5. After 4 hours, investigation of 100, 100, $100J/cm^2$ laser irradiation. The pulse mode was superior in expirimental data analysis. And it was the Burst pulse mode edge head of a family effect.

• 접착 및 계면
• /
• 제10권1호
• /
• pp.17-22
• /
• 2009

Polymer thin films were prepared by radio frequency (RF) plasma polymerization of phthalic anhydride (PA). First, monomer vaporization temperature ($100{\sim}160^{\circ}C$) was optimized by evaluating the thermal properties of thin films using differential scanning calorimeter (DSC) and measuring the root-mean-square (RMS) roughness with atomic force microscope (AFM) at the fixed plasma power of 10 W and time of 5 min in a continuous-wave (CW) mode. Plasma power (5~20 W) was then optimized by measuring the film solubility in solvents such as toluene, acetone, dimethylsulfoxide (DMSO) and 1 methylpyrrolidine (NMP). Next, pulsed mode plasma polymerization was also studied by varying the duty cycle of on-time (5, 20%) under optimized conditions of continuous-wave (CW) mode ($120^{\circ}C$, 10 W) in order to increase the anhydride functional groups. Finally, polymer thin films were characterized by Fourier transform infrared spectroscopy (FT-IR), thermogravimetric analyzer (TGA) and ${\alpha}$-step.

• 전기전자학회논문지
• /
• 제16권4호
• /
• pp.364-368
• /
• 2012

광 강도 및 위상변조 후에 단일 모드 광섬유로 첩을 보상함으로서 CW 광원으로부터 10 GHz 초단 펄스를 발생시켰다. 발생된 펄스는 0.64 nm의 스펙트럼 폭과 5.7 ps의 펄스폭을 보임으로서 시간대역 곱이 0.46인 준 변환제한된 펄스임을 보였다.

• 한국광학회지
• /
• 제32권2호
• /
• pp.62-67
• /
• 2021

본 연구에서는 모드 잠금된 ps-펄스 광섬유 레이저와 연속 발진하는 좁은 선폭의 반도체 레이저를 이용하여 주기적 분극반전된 LiNbO3(periodically poled lithium niobate; PPLN) 결정에서 합주파수 생성 연구를 수행하였다. 모드 잠금된 펄스 레이저는 중심 파장이 1560.7 nm이고 스펙트럼의 폭은 약 1.1 nm이며, 연속 발진 반도체 레이저는 중심 파장이 1551 nm이고 스펙트럼의 폭은 약 6 MHz로 동작한다. 합주파수 생성을 효과적으로 수행하기 위해서 하나의 단일 모드 광섬유를 이용하여 PPLN 결정 내부에서 두 펌프 광원을 공간적으로 완전히 중첩하였다. 모드 잠금된 펄스 레이저와 좁은 선폭의 연속발진 반도체 레이저에 의해서 모드 잠금된 펄스 형태의 778 nm인 합주파수 생성을 스펙트럼과 시간적인 변화로 확인하였다. 본 연구 결과는 주파수 제어가 가능한 광주파수 빗(optical frequency comb)을 이용한 광주파수 측정 및 고분해 레이저 분광 연구 등 다양하게 응용될 수 있을 것으로 기대된다.

• ETRI Journal
• /
• 제38권4호
• /
• pp.665-674
• /
• 2016

We designed and fabricated a semiconductor optical amplifier-integrated dual-mode laser (SOA-DML) as a compact and widely tunable continuous-wave terahertz (CW THz) beat source, and a pin-photodiode (pin-PD) integrated with a log-periodic planar antenna as a CW THz emitter. The SOA-DML chip consists of two distributed feedback lasers, a phase section for a tunable beat source, an amplifier, and a tapered spot-size converter for high output power and fiber-coupling efficiency. The SOA-DML module exhibits an output power of more than 15 dBm and clear four-wave mixing throughout the entire tuning range. Using integrated micro-heaters, we were able to tune the optical beat frequency from 380 GHz to 1,120 GHz. In addition, the effect of benzocyclobutene polymer in the antenna design of a pin-PD was considered. Furthermore, a dual active photodiode (PD) for high output power was designed, resulting in a 1.7-fold increase in efficiency compared with a single active PD at 220 GHz. Finally, herein we successfully show the feasibility of the CW THz system by demonstrating THz frequency-domain spectroscopy of an ${\alpha}$-lactose pellet using the modularized SOA-DML and a PD emitter.

• 한국인터넷방송통신학회논문지
• /
• 제18권5호
• /
• pp.97-102
• /
• 2018

본 논문에서는 W-대역 소형 레이다용 파형발생부를 설계 및 제작하였다. 제작된 파형발생부는 DDS를 적용하여 CW 및 FMCW 등 시스템에서 요구되는 다양한 파형을 고속으로 정밀하게 생성한다. 시스템 자체 점검으로 거리 지연 및 거리 추적 시험 시 별도의 점검장비 없이 레이다 자체만으로 시험이 가능하도록 LO 경로를 두 개로 설계하여 스위치를 통해 선택 가능하도록 구현하였다. 제안된 파형발생부는 대역폭 125 MHz, 위상잡음 1 kHz 오프셋(offset)에서 -91 dBc/Hz, 불요파 -63.2 dBc가 측정되었다. 본 논문에서 제시한 파형발생부를 이용하여 W-대역 소형 레이다용 송수신모듈에 바로 적용이 가능할 것으로 예상한다.

• 한국생산제조학회지
• /
• 제21권4호
• /
• pp.644-650
• /
• 2012

This paper show the 2kW fiber laser cutting properties of SS400. The study was comparison of traditional 4kW $CO_2$ Laser cutting and 2kW Fiber laser cutting characteristics for the application of Industrial 2D Laser Cutting Machine. The laser used in this investigation was an IPG YLU-2000 multi-mode Ytterbium Fiber machine with a maximum power of 2000W and a wave length of 1070 nm. The laser was used in its Continuous Wave (CW) mode with an approximately top hat beam intensity distribution. Fiber laser high quality cuts at a large range of speeds (ranging from 2000 to 3800 mm/min) which has been obtained for the 2.3mm Sheet of SS400. 2kW power Fiber laser cut was able to max. 20mm sheets of SS400 (speed range from 650 to 850 mm/min). Fiber laser cutting used in conventional hole nozzle could cut 12mm SS400 but used in special dual cutting nozzle could cut 20mm SS400.

• 한국정밀공학회지
• /
• 제22권7호
• /
• pp.19-26
• /
• 2005

The objective of this study is to investigate the influence of process parameters, such as power of laser, cutting speed of laser and material thickness, on the practical cutting region and the kerfwidth fer the case of cutting of CSP IN sheet using high power Nd:YAC laser in continuous wave(CW) mode. In order to obtain the practical cutting region and the relationship between process parameters on the kerfwidth, several laser cutting experiments are carried out. The effective heat input is introduced to consider the influence of power and cutting speed of laser on the kerfwidth together. From the results of experiments, the allowable cutting region and the relationship between the effective heat input and kerfwidth fur the case of cutting of CSP 1N sheet using high power CW Nd:YAG laser have been obtained to improve the dimensionalaccuracyofthecutarea.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2016년도 제50회 동계 정기학술대회 초록집
• /
• pp.362.2-362.2
• /
• 2016

본 실험은 CW (Continuous wave) 주파수를 가진 교류 자기장을 발생시켜 자성나노입자를 가열시키는 것이 목적이다. 이를 위해 CW 주파수 및 SMPS (Switching Mode Power Supply)를 이용해 코일에서 교류 자기장을 발생시키는 평판형 자기장 발생 장치를 자체적으로 개발하였다. 이를 이용하여 인가전압을 변화시키면서 자기장 세기의 변화를 주었다. 평판형 코일 위에는 유리 등의 원형 평판 절연체를 덮고 그 절연체 표면에 웰(Well plate)를 위치시켰고 그 안에 자성나노입자가 포함된 수용액을 넣어 교류 자기장에 노출시켰다. 자기장 측정센서(Magnetic pick up coil, Gauss Meter)를 이용하여 자기장의 세기를 측정하였고, 자성나노입자의 농도, 크기 및 자기장 세기에 따른 자성나노입자의 온도상승효과를 접촉식 온도계를 이용하여 정량적으로 측정하였다.