• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2007년도 제38회 하계학술대회
• /
• pp.812-813
• /
• 2007

The procurement of generation and transmission/Distribution capacity in vertically-integrated electric industry is sufficient by facility construction in suitable time. However, the introduction of competitive electricity market increase the efficiency of availability for facilities and fuels. As a result, long-term capacity procurement is required for stable demand-supply balance since it is expected to maintain their generation capacity at a minimum for profit maximization. In this paper, a new long-term capacity procurement mechanism is constructed, which is able to assure supplemental contribution in competitive electricity market.

• 한국지반공학회논문집
• /
• 제22권6호
• /
• pp.63-69
• /
• 2006

본 연구에서는 얕은 기초의 지지력을 평가할 수 있는 개별요소법에 근거한 해석기법이 제안되었다. 제안된 해석기법은 토체 간의 거동에 관한 적합조건을 탄소성 Winkler 스프링으로 모사함으로써 파괴면에서의 응력상태와 극한지지력을 함께 구할 수 있다. 기법의 적용성을 검토하기 위하여 단일층 및 이층지반에 설치된 얕은 기초의 지지력 해석을 수행하였다.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2022년도 봄 학술논문 발표대회
• /
• pp.113-114
• /
• 2022

The purpose of this study is to identify the rear energy transfer amount and time delay capability of the protection panel that has been impated by a projectile and the protection panel reinforced the foam polypropylene on the rear of the fiber reinforced cement itious composites, and compared and analyzed the load resistance capacity, energy dissipation capacity, and impact delay capacity when dynamic extreme load were applied to the specimen.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2020년도 가을 학술논문 발표대회
• /
• pp.65-66
• /
• 2020

When evacuation safety Design of buildings, the calculation of evacuation capacity is the most important factor that it directly impact of evacuation safety performance. However domestic standards is not consider about occupant characteristics. also the case of domestic, it has the problem that the law is partially applied when the fire safety design of buildings. Therefore, in this study we anlayze the evacuation capacity standards of each countries as basic study for development the Korean Life Safety Standards

• 한국전산구조공학회논문집
• /
• 제30권1호
• /
• pp.55-61
• /
• 2017

최근 콘크리트 궤도 슬래브 하면과 교량 바닥판 사이에 저마찰 슬라이드층을 형성하는 궤도 시스템인 슬라이딩 궤도와 관련된 연구가 활발히 진행되고 있다. 본 연구에서는 슬라이딩 궤도에서 열차 주행에 따른 횡방향 하중을 저항하기 위해 설치되는 횡방향 지지 콘크리트 블록의 전단 내하력에 대한 연구를 수행하였다. 횡방향 지지 콘크리트 블록의 전단 내하력 산정을 위해 타설경계면에서의 콘크리트 마찰 및 철근의 다월 거동을 고려한 산정 기법을 개발하다. 제안된 산정 기법은 기존의 실험에서 측정된 전단 내하력을 13~23% 정도 보수적으로 예측하는 것으로 나타났다. 이는 균열면 골재 맞물림 효과를 무시한 것에 따른 것으로, 현장에서의 타설경계면 상태가 불확실한 것을 고려할 때 횡방향 지지 콘크리트 블록에 대한 안전측 설계를 위해 제안된 산정 기법이 합리적인 것으로 판단된다. 제안된 전단 내하력 산정 기법을 토대로 횡방향 지지 콘크리트 블록에 대한 설계 방안을 마련하였다.

• Structural Engineering and Mechanics
• /
• 제75권5호
• /
• pp.529-540
• /
• 2020

The mechanical properties of timber construction have drawn more attention after the 2013 Lushan earthquake. A strong desire to preserve this ancient architectural styles has sprung up in recent years, especially for residential buildings of the mountainous areas. In the column-and-tie timber construction, continuous-tenon joints are the most common structural form to connect the chuanfang (similar to the beam in conventional structures) and the column. To study the cyclic performance of the continuous-tenon joints in column-and-tie timber construction, the reversed lateral cyclic loading tests were carried out on three 3/4 scale specimens with different section heights of the chuanfang. The mechanical behavior was assessed by studying the ultimate bending capacity, deformation ductility and energy dissipation capacity. Test results showed that the slippage of chuanfang occurred when the specimens entered the plastic stage, and the slippage degree increased with the increase of the section height of chuanfang. An obvious plastic deformation of the chuanfang occurred due to the mutual squeezing between the column and chuanfang. A significant pinching was observed on the bending moment-rotation curves, and it was more pronounced as the section height of chuanfang increased. The further numerical investigations showed that the flexural capacity and initial stiffness of the continuous-tenon joints increased with the increase of friction coefficient between the chuanfang and the column, and a more obvious increasing of bending moment occurred after the material yielding. The compressive strength perpendicular to grain of the material played a more significant role in the ultimate bending capacity of continuous-tenon joints than the compressive strength parallel to grain.

• 한국지반신소재학회논문집
• /
• 제9권3호
• /
• pp.67-75
• /
• 2010

본 연구에서는 생분해성 수지를 이용한 연직배수재에 대해 다양한 성능 평가방법을 적용하여 생분해성 플라스틱배수재의 공학적 특성을 분석하였다. 생분해성 플라스틱으로 제작한 연직배수재는 기존 합성수지 연직배수재에 비해 낮은 인장변형률을 가지며 상대적으로 낮은 인장강도를 갖지만, 연직배수재로서 가져야 할 최소한의 인장강도는 발휘하는 것으로 나타났다. 생분해성 플라스틱으로 제작한 필터는 투수성이 좋고 유효구멍크기가 작아 필터의 성능으로 매우 적합한 것으로 나타났다. 또한 생분해성플라스틱 배수재의 통수능은 필터의 강성을 개선하는 경우 국내 시방기준에도 만족할 수 있는 성능을 갖는 것으로 나타났다.

• 한국공간구조학회논문집
• /
• 제24권3호
• /
• pp.87-93
• /
• 2024

Recently, the floor construction method of buildings is rapidly being replaced by the steel deck construction method of factory products from the past cast-in-place formwork method in order to shorten construction period, reduce labor costs, and improve constructability. In this study, the bending capacity of a newly developed lattice integrated rib-type deck plate that is economical and constructible was evaluated through a simple beam test. As a result of the experiment, the lattice integrated rib-type deck installed by adding rib to the existing flat deck had excellent initial rigidity and maximum load-bearing ability, confirming the feasibility of practical use. In addition, the test specimen in which the tensile rebar is not integrated with the lattice and deck has very low initial stiffness, which is insufficient to support the load at the construction stage, and new details need to be developed to overcome this.

• 한국안전학회지
• /
• 제22권3호
• /
• pp.65-73
• /
• 2007

This paper presents the safety performance of Korean domestic construction companies including the characteristic and current status of safety management actions of the firms. Safety performance both at the head office and job sites of each construction companies, which are divided four groups by construction capacity ranking, are investigated. General recognition that there is a wide difference of safety performance among domestic construction companies by construction capacity ranking was confirmed by comparing the safety performance at the head office and the job sites of the companies under the study. Data analysis shows that the safety performance of the group I and II has the largest difference, and this difference of the group II and III and group III and IV are gradually decreased, respectively. This paper presents the safety performance improvement measures, which is applicable to safety management components consisting of both the head office and job sites safety management systems of each group (e.g., I, II, III and IV) suffering the lack of safety performance.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2018년도 춘계 학술논문 발표대회
• /
• pp.288-289
• /
• 2018

The purpose of this study is to provide the basic data of government policy by evaluating the capacity of construction companies by country. As a result, Korea ranked 7th in construction competitiveness, 13th in design competitiveness, and 7th in price competitiveness among the 20 countries to be compared. As a result of evaluating the competitiveness of construction companies by country, Korea ranked 7th overall.