• Proceedings of the KIPE Conference
• /
• 1998.07a
• /
• pp.347-351
• /
• 1998

This paper describes the controller for the improving speed control the AC servo motor. The microprocessor provides an output to the difference in command. The servo system improves the characteristics of speed control. When the motor is running at the same speed as set by the reference signal, the speed encoder also provides a signal of the same frequency. Thus, the microprocessor controlled digital techniques enable to realize the flexible performance and control which was possible with time constant. We can know that optimal speed of machining center is 75msec in 30000mm/min and actually, 75msec is using on machining center. Finally experimental results prove excellent performance of this control system. This can be reduced error with more exact measure of actual speed. The system can be adaptable to CNC machine.

• Proceedings of the KSME Conference
• /
• 2007.05a
• /
• pp.1149-1154
• /
• 2007

Fluctuation of control rod was experienced when plant was operating in normal operation mode in WH type NPPs. In order to cope with increased control rod fluctuation, the lead-lag controller setpoint for rod control system was optimized and resulted in increasing the margin of operation and minimizing unnecessary control rod movement. By optimization of the time constant, the margin of operation was increased by $1.5^{\circ}F$ and the control rod movement was not occurred due to mitigation of temperature fluctuation in loop. According to the mitigation of time constant, the margin of operation was increased but safety margin can be affected badly, so that the influences to FSAR design reference was evaluated. As the result of this evaluation, it satisfied the design reference of the existing safety analysis and was applied to NPP after obtaining the approval.

• 전기의세계
• /
• v.26 no.6
• /
• pp.48-54
• /
• 1977

The object of this work is to study the optimal control strategy of constant speed characteristics for a D.C control motor under influence of disturbance. In the course of the analysis, the linearization and time invariance schemes on motor dynamics are presumed throughout under certain prescribed conditions and the performance measure for optimality is assumed to be quadratic in state and the control effort, with the initial and final time specified. When the motor speed is deviated from a stationary operating point by any external disturbance, the optimal continuous feedback control law is investigated by the application of the calculus of variation and realizability of the required control meachanism is suggested. Finally, the comparative study of the speed reasponses of the motor, with and without the optimal control effort is also presented to confirm the obtained results.

• Journal of Institute of Control, Robotics and Systems
• /
• v.6 no.1
• /
• pp.1-7
• /
• 2000

This paper studies the delay-characteristics using the singular values and vectors of Hankel operators for input delay systems. First, the computational method of Hankel singular values and their corresponding singular vectors are introduced, and then it is analytically provea that all the Hankel singular vlues have a monotone increasing properties as the length of delay time increases. Furthermore, through a simple numerical example, it is shown that the Hankel singular values are dependent only on the ratio of the time constant of a lumped parameter system to the length of delay , and in case that the time constant is relatively larger than the delay time, the lumped parameter characteristic has a great influence on the input delay systems.

• Proceedings of the KIEE Conference
• /
• 1997.07f
• /
• pp.1964-1967
• /
• 1997

The rotor time constant variation has a large effect on the vector controlled system of induction motor. In this paper, the algorithm which compensate the misalignment of the rotor flux vector as an error caused by incorrect rotor time constant are presented. The simulations show that the proposed algorithm suitably compensates the rotor time constant.

• Proceedings of the KIEE Conference
• /
• 1999.07f
• /
• pp.2543-2545
• /
• 1999

This Paper Presents the identification of rotor time constant using Neural Network. The difference between the rotor time constant of a controller and the actual one causes the degradation of motor performance in indirect vector control scheme. The actual value is varied by heating of motor, so on-line tuning method is necessary. Therefore, the identification using Neural Network is used in this paper. The simulation using Matlab/Simulink shows that the proposed method suitably identifies the rotor time constant in the steady state

• Proceedings of the KIPE Conference
• /
• 1997.07a
• /
• pp.336-340
• /
• 1997

This paper is a study about motor technic of motion and feedforward control in order to shape cutting control on the machine tool. The shape error caused by delay of the servo system in the direction of radius at the time of circular cutting is reduced by feedforward control, shape error generated by the position command delay is minimized by using the acceleration/deceleration time constant after the interpolation. The study was verified to optimization of motion control on experiments of a vertical machining center of the machine tool.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2000.11a
• /
• pp.110-113
• /
• 2000

In general, speed control method of the elevator system has used motor pole change type or motor primary voltage control type. But it will change to vector control type in order to increase it's reliability, riding comfort and decrease material cost. It is the conception of vector control type in order to increase it's reliability, riding comfort and decrease material cost. It is the conception of vector control that primary current of the induction motor be controlled independently with magnetizing current(field current of DC motor) and torque current(armature current of DC motor). In this paper, by analyzing the effect of the time constant variation of rotor of the induction motor on the slip frequency type indirect vector control, a drive system for the motor will be constructed using a fuzzy slip frequency type indirect vector controller with fuzzy control method for estimating the vector time constant in the slip frequency type indirect vector control. The goal of this study is to enabling even more efficient speed control by constructing on elevator driver based on the newly developed drive system.

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 1998.11a
• /
• pp.162-165
• /
• 1998

A certain degree of energy saving can be possible by controlling the delay time of occupancy sensor. In this paper a control circuit is designed for automatic control of delay time setting appropriate to different situations using a digital counter, two latches and an adder. The delay time is controlled by adjusting the time constant of RC circuit through on-off control of switching devices according to adder output, which determines the base current level of switching devices. And from PSpice simulation it is verified to function properly.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.14 no.1
• /
• pp.10-20
• /
• 2002

A dynamic model of a water heater system heated by a heat pump was developed. The water heater system was composed of heat pump and hot water reservoirs. Finite volume method (FVM) was applied to describe the heat exchangers. A new constraint on electronic expansion valve (EEV) or thermostatic expansion valve (TXV) that can control superheat after the evaporator was developed. Dynamic performances were evaluated for various sizes of the reservoir. In order to compare those performances, time scale was normalized by time constant representing the characteristics of reservoir size. Time constant was determined from quasi steady-state simulation of the system. From the simulation, the size of the water heater reservoir was found to have a large influence on the transient performance of the sys- tem. Therefore, the optimization of the reservoir size is needed in a design process.