• Journal of Korean Society of Environmental Engineers
• /
• v.34 no.6
• /
• pp.406-413
• /
• 2012

Effect of three additives, chitosan, ferric chloride, and MPE50 on membrane fouling reduction was studied. They were introduced with various dosing rate into activated sludge, and changes in filtration resistance measured by the batch cell filtration test were evaluated. Both the filtration resistance and the specific cake resistance were minimized at 20 mg/g-MLSS with chitosan, 70 mg/g-MLSS with ferric chloride, and 20 mg/g-MLSS with MPE50 addition, respectively. Introduction of the additives into the activated sludge resulted in reduction of not only cake resistance, but also fouling resistance. However, the chitosan addition to three different activated sludge resulted in three different optimal dose of 10, 20, 30 mg/g-MLSS, respectively. This implies that the optimal dose is dependent on sludge characteristics rather than a constant value. Overdose above the optimal dosage always aggravated filterability in all cases. Zeta potential of sludge flocs, relative hydrophobicity, floc size distribution, soluble EPS concentration and supernatant turbidity were measured in order to analyze fouling reduction mechanism. Nearly neutral surface charge along with the largest particle size was observed at the optimal dose. This could be explained by particle destabilization and restabilization mechanism as positively charged additives were injected into sludge flocs of negative surface charge. Both soluble EPS concentration and supernatant turbidity also showed the lowest value at the optimal dose. These foulants are believed to be coagulated and entrapped in sludge flocs during flocculation. Chitosan and MPE50 which are cationic polymeric substances showed higher reduction in both soluble EPS and fine particles comparing with ferric chloride.

• Journal of Korean Society of Environmental Engineers
• /
• v.34 no.7
• /
• pp.445-453
• /
• 2012

An investigation for removal of 1-indanone (1-ID), which were commonly produced from the biological and/or chemical treatment and natural weathering of the PAHs-contaminated soils, via oxidative transformation mediated by birnessite in the presence of various phenolic mediators is described. This study also examines the potential effect of the natural occurring substance humic acid (HA) on the oxidative transformation. The experiment was carried out in aqueous phase as a batch test (10 mg/L 1-ID, 0.3 mM phenolic mediators, $1.0g/L\;{\delta}-MnO_2$, at pH 5). All of the 11 tested phenoilic mediators belong to the group of natural occurring phenols and are widely used as model constituents of humic substances. From the results of HPLC analysis, it is demonstrated that 1-ID was not reactive to birnessite itself, but it can be effectively removed in birnessite-mediated cross coupling reactions in the presence of the phenolic mediators. The percent removals of 1-ID after 2 day incubation were ranged from 9.2 to 71.2% depending on the phenolic mediators applied. The initial rate constant ($K_{int}$, $hr^{-1}$) values for the 1-ID removals obtained from the pseudo-first-order kinetic plots also widely ranged from 0.18 to 15.0. Results of the correlative analysis between the removal efficiencies and structural characteristics of phenolic mediators indicate that the transformation of the 1-ID was considerably enhanced by the addition of electron-donating substituents (e.g., -OH, $-OCH_3$) at the benzne ring, and much less enhanced by the addition of electron-withdrawing substituents (e.g., -COOH, -CHO). The presence of HA showed that removal efficiencies of 1-ID in the birnessite-phenolic mediator systems decreased with increasing HA concentrations. However at low concentration of HA (< 2 mg/L), it caused some enhancement in the removals of 1-ID as compared to the control.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.34 no.6
• /
• pp.643-651
• /
• 2001

Paddlewheel-driven circulation in a culture pond has been simulated based on the depth integrated 2 dimensional hydrodynamic model. Acceleration by paddlewheel is expressed as shaft force divided by water mass discharged by paddlewheel blades. The model has been calibrated and applied to culture ponds as following steps:- i) The model predicted velocities at every 10 m along longitudinal direction from the paddlewheel. The model was calibrated comparing the results with the measured values at mass correction factor $\alpha$ and dimensionless eddy viscosity constant $\gamma$, respectively, in a range $15\~20$ and 6. ii) Wind shear stress was simulated under conditions of direction $0^{\circ}C,\;90^{\circ}C\;and\;180^{\circ}C$ and speed 0.0, 2.5, 5.0 and 7.5 m/s. Change rate of current speed was <$1\%$ at wind in parallel or opposite direction to the paddlewheel-driven jet flow, while $4\%$ at orthogonal angle. iii) The model was then applied to 2 culture ponds located at the Western coast of Korea. The measured and predicted currents for the ponds were compared using the regression analysis. Analysis of flow direction and speed showed correlation coefficients 0.8928 and 0.6782 in pond A, 0.8539 and 0.7071 in pond B, respectively. Hence, the model is concluded to accurately predict circulation driven by paddlewheel such that it can be a useful tool to provide pond management strategy relating to paddlewheel operation and water quality.

• Korean journal of applied entomology
• /
• v.59 no.2
• /
• pp.153-163
• /
• 2020

This study was conducted to evaluate the fitness of Tetranychus kanzawai Kishida on different host plants: young and old leaves of the mandarin orange 'shiranuhi' ((Citrus unshiu × C. sinensis) × C. reticulata), Japanese violet (Viola japonica Langsd.) and kidney bean (Phaseolus vulgaris L.). The development and oviposition experiments were conducted at constant temperatures (20, 25 and 30℃) and a life table parameters were estimated. T. kanzawai could complete it's development on 'shiranuhi' young leaves, japanese violet and kidney bean, while all died during the immature period on 'shiranuhi' old leaves. The total developmental period of T. kanzawai feeding on 'shiranuhi' young leaves was 17.4, 13.4 and 10.2 days at each temperature, respectively, which was longer than 16.1, 9.5 and 7.0 days of kidney bean. The female longevity of T. kanzawai on young leaves of 'shiranuhi' were 19.1, 15.0 and 12.3 days at each temperature, respectively, and there was no significant difference from 22.1, 14.1 and 10.9 days investigated from kidney bean. The fecundity was 18.1, 23.9 and 17.8 eggs per female, which was less than them of japanese violet and kidney bean at each temperature, respectively. As a result of estimating the life table parameters based on the experimental data, intrinsic rate of increase (r_m) were significantly different from each other, and appeared in the following order: kidney (0.1542, 0.2563 and 0.3251), japanese violet (0.1087, 0.2007 and 0.2673) and 'shiranuhi' young leaves (0.0868, 0.1002 and 0.1217) at each temperature, respectively. Finally, the management strategy against T. kanzawai in citrus orchards was discussed based on the results.

• Journal of Bio-Environment Control
• /
• v.27 no.4
• /
• pp.312-318
• /
• 2018

We investigated the effect of postharvest treatments of calcium chloride, lysophosphatidyl ethanolamine (LPE) or 1-methylcyclopropene (1-MCP) on fruit quality during simulated marketing in Asian pear (Pyrus pyrifolia Nakai). 'Whangkeumbae' pear fruits were immersed in 0.25, 0.5 or 1.0% $CaCl_2$ solution with or without ultrasound (40kHz) at $25^{\circ}C$ for 3min followed by storage at $1^{\circ}C$ for 30 days simulated as abroad exportation. After simulated marketing at $25^{\circ}C$ and 80% relative humidity (RH) up for 10 days, quality parameters were evaluated. Results indicated that the ultrasound and $CaCl_2$ treatment had a synergic effect on keeping the green skin color which showed lower $a^*$ value. The combination treatment of ultrasound and 0.5% and 1.0% $CaCl_2$ significantly reduced internal browning disorders, although severe skin blemish disorder (20-23%) occurred in 1.0% $CaCl_2$ treatment. 'Wonhwang' pears were immersed in 1,000ppm LPE for 3 minutes or were fumigated in 1,000 ppb 1-MCP for 12 hours, respectively. The results of the fruit quality survey during the 21 days of distribution period are as follows. The 1-MCP treatment was maintained at a constant flesh firmness of 33N or higher during the distribution period. The LPE treated fruits had a lower physiological disorder index than the untreated group, but showed a relatively higher value than the 1-MCP treated group. In the case of 1-MCP treatment, the fruit respiration rate was significantly lower than of untreated control ($6.0mL{\cdot}kg^{-1}{\cdot}hr^{-1}$) during the simulaed marketing period. Consequently, it was expected that the postharvest treatments of 0.5% calcium chloride in pararell with ultrasound and 1-MCP fumigation can help to maintain Asian pear quality during distribution period.

• Korean journal of applied entomology
• /
• v.50 no.4
• /
• pp.373-378
• /
• 2011

The striped fruit fly, Bactrocera scutellata, damages pumpkin and other cucurbitaceous plants. The developmental period of each stage was measured at seven constant temperatures (15, 18, 21, 24, 27, 30, and $33{\pm}1.0^{\circ}C$). The developmental time of eggs ranged from 4.2 days at $15^{\circ}C$ to 0.9 days at $33^{\circ}C$. The developmental period of larvae was 4.2 days at $15^{\circ}C$, and slowed in temperatures above $27^{\circ}C$. The developmental period of pupa was 21.5 days at $15^{\circ}C$ and 7.6 days at $33^{\circ}C$. The mortality of eggs was 17.1% at $15^{\circ}C$ and 22.9% at $33^{\circ}C$, Larval mortalities (1st, 2nd, 3rd) were 24.1, 27.3 and 18.2%, respectively, at $15^{\circ}C$, Pupal mortalities were 18.2% at $15^{\circ}C$ and 23.1% at $33^{\circ}C$. The relationship between developmental rate and temperature fit both a linear model and a nonlinear model. The lower threshold temperatures of eggs, larvae, and pupae were 12.5, 10.7, and $6.3^{\circ}C$, respectively, and threshold temperature of the total immature period was $8.5^{\circ}C$. The thermal constants required to complete the egg, larval, and pupal stages were 33.2, 118.3, and 181.2 DD, respectively. The distribution of each development stages was described by a 3-parameter Weibull function.

• Tuberculosis and Respiratory Diseases
• /
• v.45 no.5
• /
• pp.1022-1030
• /
• 1998

Background : In volume-controlled ventilation, the use of inspiratory pause increases the inspiratory time and thus increases mean airway pressure and improves ventilation. But under the same I : E ratio, the effects of inspiratory pause on mean airway pressure and gas exchange are not certain. Moreover, the effects may be different according to the resistance of respiratory system. So we studied the effects of inspiratory pause on airway pressure and gas exchange under the same I : E ratio in volume-controlled ventilation. Methods: Airway pressure and arterial blood gases were evaluated in 12 patients under volume-controlled mechanical ventilation with and without inspiratory pause time 5%. The I : E ratio of 1 : 3, $FiO_2$, tidal volume, respiratory rate, and PEEP were kept constant. Results: $PaCO_2$ with inspiratory pause was lower than without inspiratory pause ($38.6{\pm}7.4$ mmHg vs. $41.0{\pm}7.7$ mmHg. p<0.01). P(A-a)$O_2$ was not different between ventilation with and without inspiratory pause $185.3{\pm}86.5$ mmHg vs. $184.9{\pm}84.9$ mmHg, p=0.766). Mean airway pressure with inspiratory pause was higher than without inspiratory pause ($9.7{\pm}4.0\;cmH_2O$ vs. $8.8{\pm}4.0\;cmH_2O$, p<0.01). The resistance of respiratory system inversely correlated with the pressure difference between plateau pressure with pause and peak inspiratory pressure without pause (r=-0.777, p<0.l), but positively correlated with the pressure difference between peak inspiratory pressure with pause and peak inspiratory pressure without pause (r=0.811, p<0.01). Thus the amount of increase in mean airway pressure with pause positively correlated with the resistance of respiratory system (r=0.681, p<0.05). However, the change of mean airway pressure did not correlated with the change of $PaCO_2$. Conclusion: In volume-controlled ventilation under the same I : E ratio of 1 : 3, inspiratory pause time of 5% increases mean airway pressure and improves ventilation. Although the higher resistance of respiratory system, the more increased mean airway pressure, the increase in mean airway pressure did not correlated with the change in $PaCO_2$.

• Journal of the Korean Chemical Society
• /
• v.33 no.1
• /
• pp.97-105
• /
• 1989

This study deals with micellar effects on hydrolyses of p-nitrophenyl carboxylic esters(p-NPCE) mediated by 2-alkylbenzimidazole(R-BI) and sodium 2-alkylbenzimidazole-5-sulfonate(R-BISO$_3$Na) in aqueous and CTABr solutions. The reactions mediated by R-BI and R-BISO$_3$Na in micellar solutions are obviously slower than those by benzimidazole(BI) and sodium benzimidazole-5-sulfonate(BISO$_3$Na) respectively, and the reaction rates were decreased with increase of lengths of alkyl groups. This prestents a striking contrast to the reactions in aqueous solutions without added CTABr, of which the reaction rates are on approximately same levels. It seems due to steric effect of alkyl groups for R-BI and R-BISO$_3$Na in the Stern layer of micelle, and it is supported by measured activation parameters(${\Delta}H^{\neq},\;{\Delta}G^{\neq}\;and\;{\Delta}S^{\neq}$) of the reactions in aqueous and micellar solutions. In addition to nucleophilic ability of benzimidazole(BI) moiety of R-BISO$_3$Na on the reactions, these compounds with long alkyl groups(nonyl to pentadecyl) which form a micelle of themselves increase the reaction rates due to their micellar catalyses in aqueous solutions, not including CTABr. We measured the isotope effects to elucidate the mechanism of hydrolyses of p-nitrophenyl carboxylic esters, and the relative first order rate constant($k'_{H_2O}/k'_{D_2O}$) are on range of 2.5∼3.2. This range is too high to conclude that the hydrolyses of p-NPA mediated by various R-BISO$_3$Na proceed by nucleophilic mechanism. In other words, the reactions are assumed to proceed in part by general basic one, as compared with the reaction catalyzed by imidazole(IM) in aqueous solution.

• Journal of the Korean Chemical Society
• /
• v.36 no.2
• /
• pp.261-272
• /
• 1992

Tetradentate Schiff base Cobalt(II)(3MeOSED)$(H_2O)_2$ complexe was synthesized and allowed to react with dry oxygen to form oxygen adducts of Cobalt(III) complexes such as ${\mu}$-peroxo type [Co(III)(3MeOSED)(DMF)]$_2O_2$ and [Co(III)(3MeOSED)(DMSO)]$_2O_2$in DMF and DMSO or superoxo type [Co(III)(3MeOSED)(Py)]$O_2$ in pyridine. The oxygen adducted complex was investigated by cyclic voltammetry and DPP method with glassy carbon electrode in 0.1M TEAP-DMF (-DMSO,-Py) as supporting electrolyte solution. As a result the reduction reaction process occurred to four steps including prewave Of $O_2^-$in 1 : 1 oxygen adducted superoxo type [Co(III)(3MeOSED)(Py)]$O_2$complex and three steps not including prewave of $O_2^-$ in 1 : 2 oxygen adducted ${\mu}$-peroxo type [Co(III)-(3MeOSED)(DMF)]$_2O_2$ and [Co(III)(3MeOSED)(DMSO)]$_2O_2$. A superoxo type [Co(III)(3MeOSED)(L)]$O_2\;(L: CH_3OH)$ was generated with oxygen in methanol. Selectively oxidized hydrazobenzene $(H_2AB)$ to trans-azobenzene(t-AB) and the rate constant k for oxidation reaction of the following equation is $(2.96 {\pm} 0.2)$${\times}$ $10^{-1}$M/sec. $H_2AB$ + Co (II)(3MeOSED)$(L_2)+O_2\;{\rightleftarrow^K}$ [Co(III)(3MeOSED)(L)]$O_2{\cdot}H_2AB{\longrightarrow^K}$ Co(II(3MeOSED)$(L)_2$+t-AB+$H_2O_2 $.

• KEPCO Journal on Electric Power and Energy
• /
• v.5 no.3
• /
• pp.209-213
• /
• 2019

Recently, demand for high energy density and long cycling stability of energy storage system has increased for application using with frequency regulation (F/R) in power grid. Supercapacitor have long lifetime and high charge and discharge rate, it is very adaptable to apply a frequency regulation in power grid. Supercapacitor can complement batteries to reduce the size and installation of batteries. Because their utilization in a system can potentially eliminate the need for short-term frequent replacement as required by batteries, hence, saving the resources invested in the upkeep of the whole system or extension of lifecycle of batteries in the long run of power grid. However, low energy density in supercapacitor is critical weakness to utilization for huge energy storage system of power grid. So, it is still far from being able to replace batteries and struggle in meeting the demand for a high energy density. But, today, LIC (Lithium Ion Capacitor) considered as an attractive structure to improve energy density much more than EDLC (Electric double layer capacitor) because LIC has high voltage range up to 3.8 V. But, many aspects of the electrochemical performance of LIC still need to be examined closely in order to apply for commercial use. In this study, in order to improve the capacitance of LIC related with energy density, we designed new method of pre-doping in anode electrode. The electrode in cathode were fabricated in dry room which has a relative humidity under 0.1% and constant electrode thickness over $100{\mu}m$ was manufactured for stable mechanical strength and anode doping. To minimize of contact resistance, fabricated electrode was conducted hot compression process from room temperature to $65^{\circ}C$. We designed various pre-doping method for LIC structure and analyzing the doping mechanism issues. Finally, we suggest new pre-doping method to improve the capacitance and electrochemical stability for LIC.