• Proceedings of the KIPE Conference
• /
• 2017.11a
• /
• pp.43-44
• /
• 2017

This paper presents design of auxiliary circuit to reduce loss of ZVT interleaved flyback converter. The ZVT interleaved converter using the conventional auxiliary circuit has a large conduction loss due to the constant circulating current in the auxiliary circuit. The auxiliary circuit proposed in this paper, which consists of the coupled inductor and DC-link capacitor, has linearly increasing or decreasing auxiliary current. Then, the conduction loss occurring in the auxiliary circuit is reduced. The validity of the proposed auxiliary circuit is verified with the prototype of 500W.

• Proceedings of the KIPE Conference
• /
• 2004.07b
• /
• pp.713-717
• /
• 2004

This is a thesis that a quarter-brick size of 100W class open-frame type on board power module comprising telecommunication application is reported. The input voltage is established between 36 and 75 in range in order for power module to be utilized for the telecommunication application, and output were set at 3.3V and 30A. A number of parts used for transformer, inductor, and hit sink are composed of PCB in order for DC-DC converter to be lowered below 8 mm. A constant current control circuit was annexed to the system as well as basic protection prototypes such as over-voltage, over-current, and over-temperature were well considered to enhance more credibility, and were tested. As a result, high circuit performance and credibility turned out to be significant.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.54 no.2
• /
• pp.133-138
• /
• 2017

This paper presents a jitter characteristic improved phase locked loop (PLL) with an RC time constant circuit. In the RC time constant circuit, LPF's voltage is inputted to a comparator through small and large RC time constant circuits. The signal through a small RC time constant circuit has almost same loop filter output voltage. The signal through a large RC time constant circuit has the average value of loop filter output voltage and does as a role of reference voltage to the comparator. The output of the comparator controls the sub-charge pump which provide a current to LPF. When the loop filter output voltage increases, the sub-charge pump discharges the loop filter and decreases loop filter output voltage. When the loop filter output voltage decreases, the sub-charge pump charges the loop filter and increases loop filter output voltage. The negative feedback loop reduces the variation of loop filter output voltage resulting in jitter characteristic improvement.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.56 no.12
• /
• pp.2150-2156
• /
• 2007

According as level of industry develops day after day, electricity load system of industry requires high level control, effectiveness and high efficiency. Among supply and control unit of suitable power supply in these load characteristic, inverter systems of constant current regulate is used widely control of lighting and electric heating system. But, problems that power factor deterioration and fast response of control, efficiency, harmonics and etc are still remain. Therefore, in this paper proposed an inverter systems with constant current regulation and power factor correction (PFC) circuit for lighting and beaconing of aerodromes. The effectiveness of the proposed system confirmed through experimental results of 10[kW] power supply system.

• IEMEK Journal of Embedded Systems and Applications
• /
• v.18 no.1
• /
• pp.9-17
• /
• 2023

This paper relates to the development of a device for measuring the efficiency of a solar panel based on a variable constant current, and proposed a standard for reuse of the solar panel. By applying a variable constant current circuit to a solar panel efficiency measuring device, it was easy to apply a maximum power point tracking (MPPT) algorithm. In addition, a load dispersion method was applied to measure the efficiency of a high-capacity solar panel. and it is possible to solve a problematic thermal runaway during a MOSFET parallel operation by applying the load dispersion method. As a result of the experiment, the solar panel efficiency measuring device was able to accommodate a large solar panel of 350W, which is the maximum measurement goal. In this paper, the validity was confirmed through the 310W solar panel efficiency measurement experiment collected after removal.

• Progress in Superconductivity and Cryogenics
• /
• v.25 no.1
• /
• pp.16-20
• /
• 2023

The International Electrotechnical Commission (IEC) 61788-26:2020 provides guidelines for measuring the critical current of Rare-earth barium copper oxide (REBCO) tapes using two methods: linear ramp and step-hold methods. The critical current measurement criterion, 1 or 0.1 μV/cm of electric field from IEC 61788-26 has been normally applied to REBCO coils or magnets. No-insulation (NI) winding technique has many advantages in aspects of electrical and thermal stability and mechanical integrity. However, the leak current from the NI REBCO coil can cause distortion in critical current measurement due to the characteristic resistance which causes the radial current flow paths. In this paper, we simulated the NI REBCO coil by applying both linear ramp and step-hold methods based on a simplified equivalent circuit model. Using the circuit analysis, we analyzed and evaluated both methods. By using the equivalent circuit model, we can evaluate the critical current of the NI REBCO coil, resulting in an estimation error within 0.1%. We also evaluate the accuracy of critical current measurement using both the linear ramp and step-hold methods. The accuracy of the linear ramp method is influenced by the inductive voltage, whereas the accuracy of the step-hold method depends on the duration of the hold-time. An adequate hold time, typically 5 to 10 times the time constant (τ), makes the step-hold method more accurate than the linear ramp method.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.23 no.7
• /
• pp.20-28
• /
• 2009

This paper presents the design of zero current switching ZCS pulse frequency modulation type DC-DC converter for magnetron power supply. A magnetron serving as the microwave source in a microwave oven is driven by a switch mode power supply (SMPS). SMPSs have the advantages of improved efficiency, reduced size and weight, regulation and the ability to operate directly from the converter DC bus. The demands of the load system and the design of the power supply required to produce constant power at 4[kV]. A magnetron power supply requires the ability to limit the load current under short circuit conditions. The current source series resonant converter is a circuit configuration which can achieve this. The main features of the proposed converter are an inherent protection against a short circuit at the output, a high voltage gain and zero current switching over a large range of output power. These characteristics make it a viable choice for the implementation of a high voltage magnetron power supply.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.40 no.4
• /
• pp.42-50
• /
• 2003

This paper presents an embedded RC oscillator which has temperature compensation circuits. The conventional RC oscillator has frequency deviation about 15%, which is caused by variation of resistors and the reference voltage of schmitt trigger from the temperature condition. In this paper, the proposed circuit use a CMOS bandgap reference having balanced current temperature coefficients as a triggering voltage of schmitt trigger. The constant current sources consist of current mirror circuit with the positive and negative temperature coefficient. The proposed circuit shows less 3% frequency deviation for variation of temperature, supply voltage and process parameters.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.20 no.2
• /
• pp.160-166
• /
• 2015

This study proposes an improved cell balancing circuit for fast equalization among lithium-ion (Li-ion) batteries. A simple voltage sensorless charge balancing circuit has been proposed in the past. This cell balancing circuit automatically transfers energy from high-to low-voltage battery cells. However, the circuit requires a switch with low on-resistance because the balancing speed is limited by the on-resistance of the switch. Balancing speed decreases as the voltage difference among the battery cells decrease. In this study, the balancing speed of the cell balancing circuit is enhanced by using the auxiliary circuit, which boosts the balancing current. The charging current is determined by the nominal battery cell voltage and thus, the balancing speed is almost constant despite the very small voltage differences among the batteries. Simulation results are provided to verify the validity of the proposed cell balancing circuit.

• 전기의세계
• /
• v.23 no.6
• /
• pp.56-59
• /
• 1974

It is well-known that the anode circuit of SCR has the current controlled negative resistance characteristic. Recently the present auther has shown that the gate circuit of SCR has the voltage controlled negative resistance characteristic for the constant anode voltage. It is shown of the equivalent model to SCR(when conducting) the voltage controlled negative resistance characteristic for gate circuit. And it is possible to make SCR gate oscillators with their desired characteristic for illustration.