• 한국생산제조학회지
• /
• 제7권3호
• /
• pp.68-78
• /
• 1998

Welding structure contains residual stress due to thermal-plastic strain during welding process, and its magnitude and distribution depend on welding conditions. Cracks initiate from various defects of the weldment, propagate and lead to final fracture, The crack initiation and propagation processes are affected by the magnitude and distribution. Therefore, the magnitude and distribution of weldment residual stress should be considered for safety design and service of welding structures. Also it is very important that more accurate assessment method of fatigue crack growth must take into account the redistributing the residual stress quantitively. because the residual stress in weldment has characteristics of its redistribution with loading magnitude, number of cycles and fatigue crack propagation. In this study fatigue crack behavior of STS-304 weldment was investigated during crack propagation into tensile residual stress region or compressive residual stress region. Crack growth rates were predicted and compared with experimental results.

• Geomechanics and Engineering
• /
• 제30권5호
• /
• pp.401-411
• /
• 2022

To obtain the dynamic mechanical properties, fracture modes, energy and brittleness characteristics of Furong Baijiao coal rock, the dynamic impact compression tests under 0, 4, 8 and 12 MPa confining pressure were carried out using the split Hopkinson pressure bar. The results show that failure mode of coal rock in uniaxial state is axial splitting failure, while it is mainly compression-shear failure with tensile failure in triaxial state. With strain rate and confining pressure increasing, compressive strength and peak strain increase, average fragmentation increases and fractal dimension decreases. Based on energy dissipation theory, the dissipated energy density of coal rock increases gradually with growing confining pressure, but it has little correlation with strain rate. Considering progressive destruction process of coal rock, damage variable was defined as the ratio of dissipated energy density to total absorbed energy density. The maximum damage rate was obtained by deriving damage variable to reflect its maximum failure severity, then a brittleness index BD was established based on the maximum damage rate. BD value declined gradually as confining pressure and strain rate increase, indicating the decrease of brittleness and destruction degree. When confining pressure rises to 12 MPa, brittleness index and average fragmentation gradually stabilize, which shows confining pressure growing cannot cause continuous damage. Finally, integrating dynamic deformation and destruction process of coal rock and according to its final failure characteristics under different confining pressures, BD value is used to classify the brittleness into four grades.

• Geomechanics and Engineering
• /
• 제30권1호
• /
• pp.93-105
• /
• 2022

With the exploitation of natural resources in China, underground resource extraction and underground space development, as well as other engineering activities are increasing, resulting in the creation of many defective rocks. In this paper, uniaxial compression tests were performed on rocks with double holes and fractures at different angles using particle flow code (PFC2D) numerical simulations and laboratory experiments. The failure behavior and mechanical properties of rock samples with holes and fractures at different angles were analyzed. The failure modes of rock with defects at different angles were identified. The fracture propagation and stress evolution characteristics of rock with fractures at different angles were determined. The results reveal that compared to intact rocks, the peak stress, elastic modulus, peak strain, initiation stress, and damage stress of fractured rocks with different fracture angles around holes are lower. As the fracture angle increases, the gap in mechanical properties between the defective rock and the intact rock gradually decreased. In the force chain diagram, the compressive stress concentration range of the combined defect of cracks and holes starts to decrease, and the model is gradually destroyed as the tensile stress range gradually increases. When the peak stress is reached, the acoustic emission energy is highest and the rock undergoes brittle damage. Through a comparative study using laboratory tests, the results of laboratory real rocks and numerical simulation experiments were verified and the macroscopic failure characteristics of the real and simulated rocks were determined to be similar. This study can help us correctly understand the mechanical properties of rocks with defects and provide theoretical guidance for practical rock engineering.

• 한국전산구조공학회논문집
• /
• 제23권1호
• /
• pp.81-94
• /
• 2010

본 연구는 선형 상보법으로 초고강도 섬유보강 콘크리트 I형보의 파괴역학적 해석을 수치해석으로 수행하였다. 기존의 보통강도 콘크리트에 대한 유사 취성 파괴역학적 수치해석을 기반으로 초고강도 섬유보강 콘크리트 재료역학적 구성모델파괴 면에 인장경화 관계를 도입함으로써 초고강도 섬유보강 콘크리트 I형 거더 해석을 개선시켰다. 상수변형률 삼각형 요소에 꼭지점 또는 요소의 중앙점 절점을 배제하고 요소의 변에 절점을 배치한 결합된 삼각형 요소를 사용하였다. 인장영역에서는 경화/연화 파괴역학적 구성모델을, 전단영역에서는 연화 파괴역학적 구성모델을, 경계절점의 압축에 대해서는 연화파괴역학적 구성모델을 사용하여 파괴역학적 해석을 수행하였다. Non-holonomic rate 형태로 경로에 의존적인 경화연화거동을 LCP로 방정식을 구성하였으며, 그 해는 PATH를 사용해서 구하였다. Piece-wise 비탄성 항복-파괴면은 두 개의 압축 caps, 두 개의 Mohr-Coulomb 파괴면, 인장항복면과 인장파괴면 등으로 구성하였다. 초고강도 섬유보강 콘크리트 거더의 변형거동과 파괴 상태와 비교하여 이 수치해석 방법에 대한 유효성을 검증하였다.

• 콘크리트학회논문집
• /
• 제26권2호
• /
• pp.159-169
• /
• 2014

이 연구에서는 철근콘크리트 전단벽의 횡하중 거동과 연성을 합리적으로 평가하기 위해서 모멘트-곡률관계를 정립하고 이로부터 단순화된 횡하중-횡변위관계를 제시하였다. 최초 휨 균열, 인장철근 항복, 최대내력, 최대내력의 80% 및 인장철근파단시점에서 모멘트와 곡률은 힘의 평형조건과 변형적합조건으로부터 정립되었다. 최대내력 이후의 곡률평가를 위한 압축측연단 콘크리트 변형률은 Razvi and Saatcioglu의 구속된 콘크리트의 응력-변형률 관계를 이용하여 최대응력의 감소계수와 횡보강근 체적지수의 함수로 제시하였다. 모멘트 평가모델은 변수연구를 통하여 인장철근지수, 수직철근지수 및 축력지수의 함수로 일반화하였다. 횡변위는 전단벽의 높이에 따라 분포된 이상화된 곡률로부터 모멘트 면적법을 이용하여 환산하였다. 제시된 횡하중-횡변위관계는 기존 실험 결과와 잘 일치하였으며, 특히 최대내력 이후의 거동을 잘 평가하였다.

• 한국지반신소재학회논문집
• /
• 제21권4호
• /
• pp.69-78
• /
• 2022

지오튜브 공법은 해안지역 해안선 침식방지와 준설토 매립 호안사면의 뒤채움 필터석 대체용으로도 널리 활용되고 있다. 본 연구는 지오텍스타일에 의해 보강되어 제작된 공시체를 현장 상태를 고려하여 등방 구속압력 10kPa, 50kPa, 100kPa 이하로 최소화하여 연직응력 재하 시 변형 거동을 파악하였다. 시험결과 공시체의 연직 변형율 7%까지는 구속압(≤100kPa)에 관계없이 지오텍스타일 조직의 이완에 따른 인장력이 발휘되는 초기 Strain Hardening 영향으로 응력-변위 거동은 동일하였다. 변형율 7%이상부터는 구속압력이 작은 공시체는 재하 시 변형이 커서 보강 지오텍스타일의 인장 저항력을 증가시키므로 Strain Hardening에 의해 파괴 시 축차응력은 상대적으로 증가하였다. 파괴 후는 급격하게 Strain Softening에 의해 취성파괴형태를 나타내면서 저하되었다. 이는 일반적인 삼축압축시험에서 셀 압이 증가되면서 전단응력도 크게 증가되는 현상과 다르다. 지오텍스타일 등방구속시험에서는 지오텍스타일의 인장변위가 일차적으로 영향을 받기 때문에 탄성계수를 급격하게 증가시키는 탄성 거동을 나타내고 있다.

• 수산해양기술연구
• /
• 제21권1호
• /
• pp.75-81
• /
• 1985

직교이방향 이층 유리섬유 강화 Epoxy 수지를 사용하여 인장축에 대해 섬유방향이 0$^{\circ}$, 15$^{\circ}$, 25$^{\circ}$ 및 45$^{\circ}$인 시료로 인장시험 및 전기절연 강도시험을 통하여 얻은 결과는 다음과 같다. 1) 섬유방향이 인장축에 대해 0$^{\circ}$에서 45$^{\circ}$로 증가함에 따라 항복응력 및 파단응력은 감소하는 경향이고 특히 0$^{\circ}$와 15$^{\circ}$ 사이에서 급격한 변화율을 보인다. 2) 파단시 변화율은 인장방향에 대한 섬유방향이 45$^{\circ}$인 경우 최대치를 나타냈고 15$^{\circ}$~45$^{\circ}$ 범위에서 급격한 변화율을 보인다. 3)섬유의 방향이 동일할 경우 인장력을 많이 받은 시료일수록 최대절연강도 값은 낮아졌고 인장방향과 섬유방향의 교각이 증가할수록 최대절연강도 값을 나타내는 압축응력의 값은 낮은 점으로 이동하는 경향을 보였다. 4) 기계적 특성과 같이 섬유방향이 45$^{\circ}$인 경우의 시료가 가장 나쁜 전기적 절연강도 특성을 나타냈다.

• 대한기계학회논문집A
• /
• 제27권7호
• /
• pp.1159-1169
• /
• 2003

This paper investigates the effects of T-stress and plastic hardening mismatch on the interfacial crack-tip stress field via finite element analyses. Plane strain elastic-plastic crack-tip fields are modeled with both MBL formulation and a full SEC specimen under pure bending. Modified Prandtl slip line fields illustrate the effects of T-stress on crack-tip constraint in homogeneous material. Compressive T-stress substantially reduces the interfacial crack-tip constraint, but increases the J-contribution by lower hardening material, J$\_$L/. For bimaterials with two elastic-plastic materials, increasing plastic hardening mismatch increases both crack-tip stress constraint in the lower hardening material and J$\_$L/. The fracture toughness for bimaterial joints would consequently be much lower than that of lower hardening homogeneous material. The implication of unbalanced J-integral in bimaterials is also discussed.

• Corrosion Science and Technology
• /
• 제20권6호
• /
• pp.466-474
• /
• 2021

A wet type scrubber for merchant vessel uses super austenitic stainless steels with pitting resistance equivalent number (PREN) of 40 or higher for operation in a harsh corrosive environment. However, it is expensive due to a high nickel content. Thus, electrochemical behavior and cavitation erosion characteristics of UNS S32750 as an alternative material were investigated. Microstructure analysis revealed fractions of ferritic and austenitic phases of 48% and 52%, respectively, confirming the existence of ferritic matrix and austenitic island. Potentiodynamic polarization test revealed damage at the interface of the two phases because of galvanic corrosion due to different chemical compositions of ferritic and austenitic phases. After a cavitation test, a compressive residual stress was formed on the material surface due to impact pressure of cavity. Surface hardness was improved by water cavitation peening effect. Hardness value was the highest at 30 ㎛ amplitude. Scanning electron microscopy revealed wave patterns due to plastic deformation caused by impact pressure of the cavity. The depth of surface damage increased with amplitude. Cavitation test revealed larger damage caused by erosion in the ferritic phase due to brittle fracture derived from different strain rate sensitivity index of FCC and BCC structures.

• Clinical Pain
• /
• 제18권2호
• /
• pp.107-110
• /
• 2019

Flexor carpi radialis (FCR) muscle is located in the forearm anteriorly that runs through a synovial fibro-osseous tunnel in the forearm. We described a case of FCR tendon rupture due to repetitive overuse injury. A 55-year-old man, right-hand dominant, presented with right forearm pain and swelling which started 3 days ago while playing amateur golf. Focal tenderness and bruising over volo-ulnar region of the right forearm were examined. Plain radiographs showed soft tissue edema around lesion area and no detectable fracture. Ultrasonography showed multiple hypoechoic lesions suspected as hematoma of the flexor muscle group. After done magnetic resonance imaging, he was diagnosed with rupture of FCR tendon at proximal origin and strain of flexor digitorum superficialis and palmaris longus muscle. He received compressive dressing and restriction of wrist range of motion for three weeks. Two months later, remaining traces of lesions were observed at the follow-up ultrasonography and the pain disappeared.