• 복합신소재구조학회 논문집
• /
• 제2권1호
• /
• pp.15-22
• /
• 2011

펄트루젼 FRP 구조용 부재는 많은 유용한 역학적, 물리적 성질 때문에 토목분야에서 구조부재의 매력적인 대체부재로 고려될 수 있다. 그러나 펄트루젼 FRP는 탄성계수가 상대적으로 낮고, 부재의 단면이 복부와 플렌지 등의 얇은 판요소로 구성되어 있기 때문에 압축재로 설계할 때 구조적인 안정성은 매우 중요한 고려사항이 된다. 따라서, 압축을 받는 구조용 부재의 설계를 위해, 판요소의 좌굴 및 후좌굴강도를 고려해야 한다. AISC/LRFD의 강구조 설계기준에서는, 후좌굴강도에 추가적인 단면 내 일정하지 않은 응력분포의 영향을 형상계수(form factor)를 사용하여 고려하고 있다. 이 논문에서는 압축력을 받는 펄트루젼 FRP 구조용 부재의 형상계수를 해석적으로 연구하였으며, 형상계수를 설정하는 과정에 대하여 제안하였다.

• 한국강구조학회 논문집
• /
• 제18권5호
• /
• pp.615-624
• /
• 2006

본 논문에서는 부재의 lay-up에 상관없이 사용할 수 있으며 복합재료 부재의 거동에 중요한 영향을 미치는 포아송 효과를 고려할 수 있는 확장된 복합재료 보이론을 제시하고, 확장된 보이론을 바탕으로 축방향 압축력을 받는 복합재료 박판부재의 좌굴식을 유도하였다. 유도된 좌굴식을 검증하기 위해서 기존에 발표된 인발성형 vinylester/E-glass 및 polyester/E-glass T형 부재의 휨-비틀림 좌굴실험결과와 vinylester/E-glass H형 부재의 휨 좌굴실험결과를 수치예제로 사용하였다. 이론적 좌굴하중과 실험적 좌굴하중 및 유한요소해석 결과와의 비교를 통하여 본 연구에서 제안된 좌굴식이 인발성형부재의 좌굴하중을 7% 정도 안전측으로 예측하는 것을 알 수 있었다.

• 한국공간구조학회논문집
• /
• 제16권2호
• /
• pp.89-96
• /
• 2016

Cable structures are lightweight structures of flexible type, cable members have only axial stiffness related to tension, they can carry neither bending nor compression. This study is the analysis of cable truss systems are composed of upper and low cables by connecting bracing cables, the structural principle is based on a tensegrity system by using bracing tension members, discontinuous compression members and continuous tension members. A hanging roof of cable truss system is too flexible against vertical loads, most cable members are stabilized by connecting the prestressed upper and lower cable by bracing cables. A cable truss roof system is formed by adding a set of cables with reverse curvature to the suspension cables. With the sets of cables having opposite curvature to each other, cable truss is able to carry vertical load in both upward and downward direction with equal effectiveness, and then a cable truss acts as load bearing elements by the assemble of ridge cables, valley cables and bracing cables. This paper will be shown the geometric non-linear analysis result of cable truss systems with various sag ratio for deflections and tensile forces, the analytical results are compared with the results of other researchers.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1999년도 학회창립 10주년 기념 1999년도 가을 학술발표회 논문집
• /
• pp.705-708
• /
• 1999

Advanced composite materials such as carbon fiber, aramid, and glass fiber sheet, are widely used recently to strengthening existing reinforced concrete structures. The purpose of this paper was to investigate the mechanical characteristics of concrete compressive members confined with carbon fiber sheet and evaluate the efficiency of the strengthening under load actions. Uniaxal compression tests of concrete compressive members confined with carbon fiber sheet were experimentally used to develop a relationship between the axial stresses and the lateral stresses. The resulting axial and lateral strains were used to determine the confinement effect of concrete compressive members.

• Steel and Composite Structures
• /
• 제3권4호
• /
• pp.261-275
• /
• 2003

Truss members built-up with double angles back-to-back have monosymmetric cross-section and twisting always accompanies flexion upon the onset of buckling about the axis of symmetry. Approximate formulae for calculating the buckling capacity are presented in this paper for routine design purpose. For a member susceptible only to flexural buckling, its optimal cross-section should consist of slender plate elements so as to get larger radius of gyration. But, occurrence of twisting changes the situation owing to the weakness of thin plates in resisting torsion. Criteria for limiting the leg slenderness are discussed herein. Truss web members in compression are usually considered as hinged at both ends for out-of-plane buckling. In case one (or both) end of member is not supported laterally by bracing member, its adjoining members have to provide an elastic support of adequate stiffness in order not to underdesign the member. The stiffness provided by either compression or tension chords in different cases is analyzed, and the effect of initial crookedness of compression chord is taken into account. Formulae are presented to compute the required stiffness of chord member and to determine the effective length factor for inadequately constrained compressive diagonals.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2004년도 춘계학술발표대회 논문집
• /
• pp.223-227
• /
• 2004

The pultruded structural shapes are usually composed of thin-walled plate elements. Because the composite material has relatively low elastic moduli, the design of pultruded compression members may not be governed by the material strength limit state but by the stability limit state such as the local buckling or the global buckling. Therefore, the stability limit state must be checked to design pultruded columns. In this research, the local buckling analysis of pultruded I-shape column was conducted for various composite materials using the closed-form solution. To establish the design guidelines for the local buckling of pultruded I-shape compression members, the simplified form of equation to find the local buckling coefficient of pultruded I-shape column was proposed as a function of mechanical properties and the width ratio of plate components using the results obtainde by the closed-form solution. In order to verify the validity of proposed solution, the results obtained by the proposed approximate solution were compared with those of the closed-form solution and the experimental results.

• Steel and Composite Structures
• /
• 제34권2호
• /
• pp.171-188
• /
• 2020

The past research on cold-formed steel (CFS) flexural members have proved that rectangular hollow flanged sections perform better than conventional I-sections due to their higher torsional rigidity over the later ones. However, CFS members are vulnerable to local buckling, substantially due to their thin-walled features. The use of packing, such as firmly connected timber planks, to the flanges of conventional CFS lipped I-sections can drastically improve their flexural performance as well as structural efficiency. Whilst several CFS composites have been developed so far, only limited packing materials have been tried. This paper presents a series of tests carried out on different rectangular hollow compression flanged sections with innovative packing materials. Four-point flexural tests were carried out to assess the flexural capacity, failure modes and deformed shapes of the CFS composite beam specimens. The geometric imperfections were measured and reported. The North American Specifications and Indian Standard for cold-formed steel structures were used to compare the design strengths of the experimental specimen. The test results indicate clearly that CFS rectangular 'compression' flanged composite beams perform significantly better than the conventional rectangular hollow flanged CFS sections.

• Steel and Composite Structures
• /
• 제32권1호
• /
• pp.59-66
• /
• 2019

Hollow steel-reinforced concrete-filled GFRP tubular member is a new kind of composite members. Firstly set the mold in the GFRP tube (non-bearing component), then set the longitudinal reinforcements with stirrups (steel reinforcement cage) between the GFRP tube and the mold, and filled the concrete between them. Through the axial compression test of the hollow steel-reinforced concrete-filled GFRP tubular member, the working mechanism and failure modes of composite members were obtained. Based on the experiment, when the load reached the ranges of $55-70%P_u$ ($P_u-ultimate$ load), white cracks appeared on the surface of the GFRP tubes of specimens. At that time, the confinement effects of the GFRP tubes on core concrete were obvious. Keep loading, the ranges of white cracks were expanding, and the confinement effects increased proportionally. In addition, the damages of specimens, which were accompanied with great noise, were marked by fiber breaking and resin cracking on the surface of GFRP tubes, also accompanied with concrete crushing. The bearing capacity of the axially compressed components increased with the increase of reinforcement ratio, and decreased with the increase of hollow ratio. When the reinforcement ratio was increased from 0 to 4.30%, the bearing capacity was increased by about 23%. When the diameter of hollow part was decreased from 55mm to 0, the bearing capacity was increased by about 32%.

• 대한토목학회논문집
• /
• 제32권4A호
• /
• pp.217-225
• /
• 2012

본 연구에서는 비대칭 연결재를 갖는 조립식 압축부재의 연결재 종류에 따른 좌굴 거동을 알아보기 위한 실 대형 실험을 실시하였다. 압축부재인 H-300 형강 10 m 부재 3개를 볼트 연결하여 총 길이 30 m가 되도록 2 m 간격으로 2열 배치한 후 연결재 종류가 띠판, ㄷ형강, 복 ㄷ형강인 경우에 대하여 압축 실험을 실시하였다. 본 논문에서는 연결재 종류에 따른 실험 좌굴 하중을 평가하고 이를 유한요소해석 결과인 좌굴하중과 Timoshenko 식에 의한 좌굴하중과 비교 분석 하였으며, 연결재 종류에 따른 조립식 압축부재의 좌굴 거동으로 인한 종방향 변위, 횡방향 변위, 변형률 등을 분석하였다. 실험 결과 비대칭 연결재를 갖는 조립식 압축부재의 연결재가 띠판일 때 보다 복 ㄷ형강일 때의 좌굴 하중은 4.2%, ㄷ형강일 때는 36.6% 감소하는 것으로 나타났다.

• 산업경영시스템학회지
• /
• 제20권44호
• /
• pp.323-332
• /
• 1997

This study evaluated the compression force at the L5/S1 disc using EMG(Electromyography). EMG signals were analyzed under the condition of fixed vertical factor (20Cm∼80Cm), two horizontal factors (35Cm, 55Cm), and two weight factors (10Kg, 25Kg) 2 times per minute for each posture. Also, the result was compared with the compression force of each posture which computated by the equation of NIOSH(National Institute for Occupational Safety and Health) guide to manual lifting(1991). The experimental result show that EMG signals have more an effect on the Weight than the Horizontal factors. Also, there are not significant differences on the analysis result of EMG signals between Health members and not, because the body buildings which doing Health members are not enhanced the motor unit due to the MMH(Manual Material Handing).